AXIOMTEK SHB101 Series User manual

SHB101
lntel®Core™2 Quad/Core™2 Duo
Celeron®Processor
PICMG 1.3 Full-Size Single Board
Computer
User’s Manual

ii
Disclaimers
This manual has been carefully checked and believed to contain accurate information.
Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third
party’s rights, and any liability arising from such use.
Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy,
completeness or usefulness of any information in this document. Axiomtek does not make any
commitment to update the information in this manual.
Axiomtek reserves the right to change or revise this document and/or product at any time
without notice.
No part of this document may be reproduced, stored in a retrieval system, or transmitted, in
any form or by any means, electronic, mechanical, photocopying, recording, or otherwise,
without the prior written permission of Axiomtek Co., Ltd.
CAUTION
If you replace wrong batteries, it causes the danger of explosion. It is recommended by the
manufacturer that you follow the manufacturer’s instructions to only replace the same or
equivalent type of battery, and dispose of used ones.
Copyright 2013 Axiomtek Co., Ltd.
All Rights Reserved
April 2013, Version A4
Printed in Taiwan

iii
ESD Precautions
Computer boards have integrated circuits sensitive to static electricity. To prevent chipsets
from electrostatic discharge damage, please take care of the following jobs with precautions:
Do not remove boards or integrated circuits from their anti-static packaging until you are
ready to install them.
Before holding the board or integrated circuit, touch an unpainted portion of the system
unit chassis for a few seconds. It discharges static electricity from your body.
Wear a wrist-grounding strap, available from most electronic component stores, when
handling boards and components.
Trademarks Acknowledgments
Axiomtek is a trademark of Axiomtek Co., Ltd.
Windows®is a trademark of Microsoft Corporation.
AMI is a trademark of American Megatrend Inc.
IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation.
Intel®CoreTM i7 / CoreTM i5 / CoreTM i3 are trademarks of Intel Corporation.
Winbond is a trademark of Winbond Electronics Corp.
Realtek is a trademark of Realtek Semi-Conductor Co., Ltd.
Other brand names and trademarks are the properties and registered brands of their
respective owners.

iv
Table of Contents
Disclaimers.....................................................................................................ii
ESD Precautions...........................................................................................iii
Chapter 1 Introduction............................................. 1
1.1 Specifications......................................................................................1
1.2 Utilities Supported ..............................................................................3
1.3 I/O Bracket...........................................................................................3
Chapter 2 Board and Pin Assignments.................... 5
2.1 Board Dimensions ..............................................................................5
2.2 Board Layout.......................................................................................6
2.3 Jumper Settings..................................................................................7
2.3.1 COM2 Mode Select Jumpers (JP1, JP2, JP3)............................................ 7
2.3.2 CMOS Clear Jumper (JP6) ......................................................................... 7
2.3.3 ATX Auto Power On/Off (JP7)..................................................................... 8
2.4 Connectors ..........................................................................................9
2.4.1 ATX 4 Pin 12V In Connector (CN2)........................................................... 10
2.4.2 Front Panel Connector (CN3) ................................................................... 10
2.4.3 LAN1, LAN2 Link/Active LED Connectors (CN4, CN7) .............................11
2.4.4 LAN1, LAN2 Speed LED Connectors (CN5, CN6).....................................11
2.4.5 COM Port RS-232 Pin Assignment (COM1, COM2)..................................11
2.4.6 COM2 RS-422/485 Pin Assignment...........................................................11
2.4.7 CPU Fan Connector (FAN1) ..................................................................... 12
2.4.8 System Fan Connectors (FAN2, FAN3).................................................... 12
2.4.9 Floppy Disk Port Connector (FDD1) ......................................................... 12
2.4.10 Intel® HD Audio Digital Header (HDA1).................................................... 13
2.4.11 PS/2 Keyboard, Mouse Connector (KB1, MS1)........................................ 13
2.4.12 Ethernet RJ-45 Connectors (LAN1, LAN2)............................................... 13
2.4.13 Parallel Port Connector (PRN1)................................................................ 14
2.4.14 SATA Connectors (SATA1~6).................................................................... 14
2.4.15 USB Connectors (USB1, USB2)............................................................... 15
2.4.16 USB Port Connector (USB3, USB4) ......................................................... 15
2.4.17 DB15 CRT Connector (VGA1) .................................................................. 15
Chapter 3 Hardware Installation ........................... 17
3.1 Installing the Processor....................................................................18
3.2 Installing the Memory .......................................................................21

v
Chapter 4 Hardware Description ........................... 23
4.1 Microprocessors ...............................................................................23
4.2 BIOS ...................................................................................................23
4.3 System Memory.................................................................................23
4.4 I/O Port Address Map........................................................................24
4.5 Interrupt Controller (IRQ) Map .........................................................25
Chapter 5 PHOENIX-AWARD BIOS Utility .............. 27
5.1 Entering Setup...................................................................................27
5.2 Control Keys......................................................................................28
5.3 Getting Help.......................................................................................29
5.4 Main Menu..........................................................................................29
5.5 Standard CMOS Setup Menu............................................................30
5.6 Advanced BIOS Features .................................................................32
5.7 Advanced Chipset Features.............................................................37
5.8 Integrated Peripherals ......................................................................39
5.9 Power Management Setup................................................................43
5.10 PnP/PCI Configuration Setup...........................................................46
5.11 PC Health Status ...............................................................................48
5.12 Frequency/Voltage Control...............................................................49
5.13 Load Fail-Safe Defaults.....................................................................50
5.14 Load Optimized Defaults ..................................................................51
5.15 Set Supervisor/User Password........................................................52
5.16 Save & Exit Setup..............................................................................53
5.17 Exit Without Saving...........................................................................54
Chapter 6 Installation of Drivers ........................... 55
6.1 Installing Chipset Driver...................................................................55
6.2 Installing VGA Driver.........................................................................57
6.3 Installing LAN Driver.........................................................................59
Appendix A Watchdog Timer .................................... 63
Watchdog Timer Setting..............................................................................63
Using the Watchdog Function ....................................................................63
Appendix B PCI IRQ Routing..................................... 65

vi
Appendix C Configuring SATA for RAID Function..... 67
Configuring SATA Hard Drive(s) for RAID Function (Controller: Intel®
ICH9R/DO DH only)......................................................................................67
Appendix D PICMG V1.3 Interface Definition........... 76

SHB101 LGA775 SBC User’s Manual
Introduction 1
Chapter 1
Introduction
The SHB101 PICMG 1.3 full-size Single Board Computer supports LGA775 socket for Intel®
Core™2 Quad / Core™2 Duo/Celeron®processors with 45/65nm technology and FSB
800/1066/1333 MHz. The board integrates Intel®Q35 and ICH9R chipset that delivers
outstanding system performance through high-bandwidth interfaces, multiple I/O functions for
interactive applications and various embedded computing solutions. There are four 240-pin
DDR2 DIMM sockets for dual channel DDR2 667/800, maximum memory capacity up to 8GB.
The board also features dual Gigabit Ethernet, six serial ATAports at maximum transfer rate up
to 3Gbs, and SATA RAID 0/1/5/10 by ICH9R. Ten USB 2.0 high speed compliant ports and
built-in Intel®HD Audio Digital Header (optional) can achieve the best stability and reliability
for industrial applications.
1.1 Specifications
CPU
Intel®Core™2 Quad / Core™2 Duo/Celeron®processors
System Chipset
Intel®Q35 and ICH9R
CPU Socket
LGA775 Socket
Front-Side Bus
800/1066/1333 MHz
BIOS
Phoenix-Award BIOS via SPI interface with socket

SHB101 LGA775 SBC User’s Manual
2 Introduction
System Memory
Four 240-pin DDR2 DIMM sockets
Maximum up to 8GB DDR2 memory
Support DDR2 667/800 memory
L2 Cache
Integrated in CPU
Onboard Multi-I/O
Parallel Port: one 26-pin 2.54 pitch box-header, SPP/EPP/ECP supported
Serial Port: one for RS-232 (COM1) and one port for RS-232/422/485 (COM2)
Floppy controller: supports two drives (1.44MB for each)
USB Interface
Ten USB ports compliant with USB Spec. Rev. 2.0 (Six ports on SHB101, four ports
to SHB connector-C golden fingers)
VGA Controller
Chipset -- Intel®integrated Graphics Gen3.5 on Intel®Q35 supports 3D, 2D, video
capabilities
Memory Size -- Intel®DVMT 128/256MB supported; preallocated memory for frame
buffer option as 8MB
Resolution -- Analog output -- the analog port utilizes an integrated 350MHz 24-bit
RAMDAC that can directly drive a standard progressive scan analog monitor up to a
resolution of 2048x1536 pixels with 32-bit color at 75Hz
Analog Output Interface -- CRT from DAC output via 15-pin D-Sub connector on the
edge; CRT always ON supported
Ethernet
The LAN1/LAN2 is 82573L Ethernet controller support 10/100/1000 Mb/s
Dual PCI-Express x1 LAN
Serial ATA
Support Serial ATA/Serial ATA II
Six Serial ATA-II ports, 3GB/s performance and SATA RAID 0/1/5/10 by ICH9R
Audio
16-pin 2.54 pin-header (Intel®HD Audio Digital Header)
This header can be for Audio kitAX93242 (optional)
Hardware Monitoring
Monitoring temperatures, voltages, and cooling fan status
Watchdog Timer
Reset Supported (1-255 level)
Dimensions
338mm x 126mm
Note
All specifications and images are subject to change without notice.

SHB101 LGA775 SBC User’s Manual
Introduction 3
1.2 Utilities Supported
Intel®Q35 Utility and Drivers
VGA Drivers
Ethernet Utility and Drivers
RAID Utility
1.3 I/O Bracket

SHB101 LGA775 SBC User’s Manual
4 Introduction
This page is intentionally left blank.

SHB101 LGA775 SBC User’s Manual
Board and Pin Assignments 5
Chapter 2
Board and Pin Assignments
2.1 Board Dimensions

SHB101 LGA775 SBC User’s Manual
6 Board and Pin Assignments
2.2 Board Layout

SHB101 LGA775 SBC User’s Manual
Board and Pin Assignments 7
2.3 Jumper Settings
Proper jumper settings configure the SHB101 to meet your application purpose.
2.3.1 COM2 Mode Select Jumpers (JP1, JP2, JP3)
These jumpers select the COM2 port’s communication mode to operate RS-232 or
RS-422/485.
Description
Function
Jumper Setting
COM2
RS-232
(Default)
JP1
JP2
JP3
RS-422
JP1
JP2
JP3
RS-485
JP1
JP2
JP3
2.3.2 CMOS Clear Jumper (JP6)
You may need to use this jumper is to clear the CMOS memory if incorrect BIOS
settings.
Description
Function
Jumper Setting
CMOS Clear
Normal
(Default)
Clear CMOS

SHB101 LGA775 SBC User’s Manual
8 Board and Pin Assignments
2.3.3 ATX Auto Power On/Off (JP7)
When Jumper JP7 is set OPEN for AC power input, the system will be automatically
power ON without pressing soft power button; when JP7 is SHORT for AC power input, it
is necessary to manually press soft power button to make the system power ON.
Note
This function is similar to the feature of Power On after Power Failed,
which is controlled by hardware circuitry instead of BIOS.
Description
Function
Jumper Setting
ATX Auto Power
On/Off
Disable
(Default)
Enable

SHB101 LGA775 SBC User’s Manual
Board and Pin Assignments 9
2.4 Connectors
Connectors connect this board with other parts of the system. Loose or improper connection
might cause problems. Make sure all connectors are properly and firmly connected.
Here is a summary table shows you all connectors on the board.
Connectors
Label
Connectors
Label
ATX 4 Pin 12V In
CN2
Floppy Connector
FDD1
Front Panel Connector
CN3
Parallel Port
PRN1
LAN2 Link / Active LED
CN4
Serial ATA Connectors
SATA1~6
LAN2 Speed LED
CN5
USB Connector
USB1~4
LAN1 Speed LED
CN6
DB15 CRT Connector
VGA1
LAN1 Link / Active LED
CN7
DDRII DIMM Sockets
DDR1~4
Serial Port1 Connector
COM1
PS/2 Mouse Connector
MS1
Serial Port2 Connector
COM2
PS/2 Keyboard Connector
KB1
CPU FAN Connector
FAN1
Intel HD Audio Digital Header
HDA1
System FAN Connector
FAN2
LAN1 Connector
LAN1
System FAN Connector
FAN3
LAN2 Connector
LAN2

SHB101 LGA775 SBC User’s Manual
10 Board and Pin Assignments
2.4.1 ATX 4 Pin 12V In Connector (CN2)
You can connect it to the ATX12V power supply for CPU Core Voltage.
Pin
Signal
1
GND
2
GND
3
+12V
4
+12V
2.4.2 Front Panel Connector (CN3)
Power LED
This 3-pin connector denoted as Pin 1 and Pin 5 connects the system power LED
indicator to such a switch on the case. Pin 1 is assigned as +, and Pin 5 as -. The Power
LED lights up when the system is powered ON. Pin 3 is defined as GND.
External Speaker and Internal Buzzer Connector
Pin 2, 4, 6 and 8 can be connected to the case-mounted speaker unit or internal buzzer.
While connecting the CPU card to an internal buzzer, please short pins 2-4; while
connecting to an external speaker, you need to set pins 2-4 to Open and connect the
speaker cable to pin 8 (+) and pin 2 (-).
ATX Power On/Off Button
This 2-pin connector denoted as Pin 9 and 10 connects the front panel’s ATX power
button to the CPU card, which allows users to control ATX power supply to be power
on/off.
System Reset Switch
Pin 11 and 12 can be connected to the case-mounted reset switch that reboots your
computer instead of turning OFF the power switch. It is a better way to reboot your
system for a longer life of the system’s power supply.
1. HDD Activity LED
This connection is linked to hard drive activity LED on the control panel. LED flashes
when HDD is being accessed. Pin 13 and 14 connect the hard disk drive to the front
panel HDD LED, Pin 13 assigned as -, and Pin 14 as +.

SHB101 LGA775 SBC User’s Manual
Board and Pin Assignments 11
2.4.3 LAN1, LAN2 Link/Active LED Connectors (CN4, CN7)
Pin
Signal
1
LED (+)
2
LED (-)
2.4.4 LAN1, LAN2 Speed LED Connectors (CN5, CN6)
Pin
Signal
1
100, Low Active
2
+ 3.3V
3
1000, Low Active
2.4.5 COM Port RS-232 Pin Assignment (COM1, COM2)
The serial interface for the board consists of COM1 port (COM1) support for RS-232,
and COM2 (COM2) for RS-232/RS422/RS485.
Pin
Signal
Pin
Signal
2
4
6
1
3
5
78
910
1
Data Carrier Detect
(DCD)
2
Data Set Ready (DSR)
3
Receive Data (RXD)
4
Request to Send (RTS)
5
Transmit Data (TXD)
6
Clear to Send (CTS)
7
Data Terminal Ready
(DTR)
8
Ring Indicator (RI)
9
Ground (GND)
10
Ground (GND)
2.4.6 COM2 RS-422/485 Pin Assignment
COM2 Serial Port 10-pin (Box-header) Connector Pin Assignment list
Pin
Signal
RS-422
RS-485
1
TX-
DATA-
2
No connector
No connector
3
TX+
DATA+
4
No connector
No connector
5
RX+
No connector
6
No connector
No connector
7
RX-
No connector
8
No connector
No connector
9
GND
GND
10
GND
GND

SHB101 LGA775 SBC User’s Manual
12 Board and Pin Assignments
2.4.7 CPU Fan Connector (FAN1)
A CPU fan is always needed for cooling CPU heat. The CPU fan connector FAN1
provides power to the CPU fan.
Pin
Signal
1
Ground
2
+12V
3
Rotation Detection
4
Speed Control
2.4.8 System Fan Connectors (FAN2, FAN3)
You can connect the system cooling fan cable to FAN2/FAN3 for system cooling fan
power.
Pin
Signal
1
GND
2
+12V
3
Rotation Detection
2.4.9 Floppy Disk Port Connector (FDD1)
The board provides a 34-pin header type connector, FDD1, supporting up to two floppy
drives. The floppy drives may be any one of the following types: 5.25" 360KB/1.2MB and
3.5" 720KB/1.44MB/2.88MB.
Pin
Signal
Pin
Signal
Pin
Signal
1
GND
2
Drive Density Select
3
GND
4
No connector
5
GND
6
No connector
7
GND
8
Index#
9
GND
10
Motor enable A#
11
GND
12
No connector
13
GND
14
Drive select A#
15
GND
16
No connector
17
GND
18
Direction#
19
GND
20
STEP#
21
GND
22
Write data#
23
GND
24
Write gate#
25
GND
26
Track 0 #
27
GND
28
Write protect#
29
No connector
30
Read data#
31
GND
32
Head selection#
33
No connector
34
Disk change#

SHB101 LGA775 SBC User’s Manual
Board and Pin Assignments 13
2.4.10 Intel® HD Audio Digital Header (HDA1)
Pin
Signal
Pin
Signal
1
BCLK
2
GND
3
RST#
4
VCC3
5
SYNC
6
GND
7
SDOUT
8
VCC3
9
SDI0
10
+12V
11
No connector
13
No connector
14
3VDUAL
15
No connector
16
GND
2.4.11 PS/2 Keyboard, Mouse Connector (KB1, MS1)
The board provides the Keyboard (KB1)/ Mouse (MS1) interface with a 5-pin connector.
Pin
Signal
1
Clock
2
DATA
3
No connector
4
GND
5
VCC
2.4.12 Ethernet RJ-45 Connectors (LAN1, LAN2)
The RJ-45 connectors LAN1 and LAN2 are for Ethernet. To connect the board to
100-Base-T or 1000-Base-T hub, just plug one end of the cable into LAN1 and connect
the other end (phone jack) to a 100-Base-T hub or 1000-Base-T hub.
Pin
Signal
12345678
A B
1
Tx+ (Data transmission positive)
2
Tx- (Data transmission negative)
3
Rx+(Data reception positive)
4
RJ-1(For 1000 base T-Only)
5
RJ-1(For 1000 base T-Only)
6
Rx- (Data reception negative)
7
RJ-1(For 1000 base T-Only)
8
RJ-1(For 1000 base T-Only)
A
Active LED
B
Speed LED

SHB101 LGA775 SBC User’s Manual
14 Board and Pin Assignments
2.4.13 Parallel Port Connector (PRN1)
Print Port Connector [Default]
This board has a multi-mode parallel port to support:
1. Standard Mode:
IBM PC/XT, PC/AT and PS/2are compatible with bi-directional parallel port.
2. Enhanced Mode:
Enhance parallel port (EPP) is compatible with EPP 1.7 and EPP 1.9 (IEEE 1284
compliant).
3. High Speed Mode:
Microsoft and Hewlett Packard extended capabilities port (ECP) is IEEE 1284 compliant.
Pin
Signal
Pin
Signal
2
4
6
1
3
5
7 8
9
11
13
15
10
12
14
16
17
19
21
23
25
18
20
22
24
26
1
Strobe#
2
Auto Form Feed#
3
Data 0
4
Error#
5
Data 1
6
Initialize#
7
Data 2
8
Printer Select In#
9
Data 3
10
GND
11
Data 4
12
GND
13
Data 5
14
GND
15
Data 6
16
GND
17
Data 7
18
GND
19
Acknowledge#
20
GND
21
Busy
22
GND
23
Paper Empty#
24
GND
25
Printer Select
26
GND
2.4.14 SATA Connectors (SATA1~6)
These SATA connectors are for high-speed SATA interface ports and they can be
connected to hard disk devices.
Pin
Signal
1
GND
2
SATA_TX+
3
SATA_TX-
4
GND
5
SATA_RX-
6
SATA_RX+
7
GND