Axis P3343 User manual

ENGLISH DEUTSCH ITALIANO ESPAÑOL
INSTALLATION GUIDE
FRAN
Ç
AIS
AXIS P33 Network Camera Series
AXIS P3343 Network Camera
AXIS P3344 Network Camera
AXIS P3343-V Network Camera
AXIS P3344-V Network Camera

About this Document
This document includes instructions for installing AXIS
P3343, AXIS P3344, AXIS P3343-V and AXIS P3344-V on
your network. Previous experience of networking will be
beneficial when installing the product.
Legal Considerations
Video and audio surveillance can be prohibited by laws
that vary from country to country. Check the laws in
your local region before using this product for
surveillance purposes.
This product includes one (1) H.264 decoder license. To
purchase further licenses, contact your reseller.
Electromagnetic Compatibility (EMC)
This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is
no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to
radio or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or
more of the following measures: Re-orient or relocate
the receiving antenna. Increase the separation between
the equipment and receiver. Connect the equipment to
an outlet on a different circuit to the receiver. Consult
your dealer or an experienced radio/TV technician for
help. Shielded (STP) network cables must be used with
this unit to ensure compliance with EMC standards.
USA - This equipment has been tested and found to
comply with the limits for a Class B computing device
pursuant to Subpart B of Part 15 of FCC rules, which are
designed to provide reasonable protection against such
interference when operated in a commercial
environment. Operation of this equipment in a
residential area is likely to cause interference, in which
case the user at his/her own expense will be required to
take whatever measures may be required to correct the
interference.
Canada - This Class B digital apparatus complies with
Canadian ICES-003.
Europe - This digital equipment fulfills the
requirements for radiated emission according to limit B
of EN55022, and the requirements for immunity
according to EN55024 residential and commercial
industry.
Japan - This is a class B product based on the standard
of the Voluntary Control Council for Interference from
Information Technology Equipment (VCCI). If this is used
near a radio or television receiver in a domestic
environment, it may cause radio interference. Install and
use the equipment according to the instruction manual.
Australia - This electronic device meets the
requirements of the Radio communications
(Electromagnetic Compatibility) Standard AS/NZS
CISPR22.
Equipment Modifications
This equipment must be installed and used in strict
accordance with the instructions given in the user
documentation. This equipment contains no
user-serviceable components. Unauthorized equipment
changes or modifications will invalidate all applicable
regulatory certifications and approvals.
Liability
Every care has been taken in the preparation of this
document. Please inform your local Axis office of any
inaccuracies or omissions. Axis Communications AB
cannot be held responsible for any technical or
typographical errors and reserves the right to make
changes to the product and documentation without
prior notice. Axis Communications AB makes no
warranty of any kind with regard to the material
contained within this document, including, but not
limited to, the implied warranties of merchantability
and fitness for a particular purpose. Axis
Communications AB shall not be liable nor responsible
for incidental or consequential damages in connection
with the furnishing, performance or use of this material.
RoHS
This product complies with both the European
RoHS directive, 2002/95/EC, and the Chinese
RoHS regulations, ACPEIP.
WEEE Directive
The European Union has enacted a Directive
2002/96/EC on Waste Electrical and Electronic
Equipment (WEEE Directive). This directive is
applicable in the European Union member
states.
The WEEE marking on this product (see right) or its
documentation indicates that the product must not be
disposed of together with household waste. To prevent
possible harm to human health and/or the environment,
the product must be disposed of in an approved and
environmentally safe recycling process. For further
information on how to dispose of this product correctly,
contact the product supplier, or the local authority
responsible for waste disposal in your area.
Business users should contact the product supplier for
information on how to dispose of this product correctly.
This product should not be mixed with other commercial
waste. For more information, visit
www.axis.com/techsup/commercial waste
Support
Should you require any technical assistance, please
contact your Axis reseller. If your questions cannot be
answered immediately, your reseller will forward your
queries through the appropriate channels to ensure a
rapid response. If you are connected to the Internet, you
can:
• download user documentation and firmware updates
• find answers to resolved problems in the FAQ database.
Search by product, category, or phrases
• report problems to Axis support by logging in to your
private support area.
The AXIS P3343, AXIS P3344, AXIS P3343-V and
AXIS P3344-V Network Cameras use a 3.0V CR2032
Lithium battery.

AXIS P3343/P3343-V/P3344/P3344-V Installation Guide Page 3
ENGLISH
AXIS P3343/P3343-V/P3344/P3344-V
Network Camera
Follow these instructions to install the AXIS P3343/P3343-V/P3344/P3344-V Network Camera:
Notes:
• Before you begin, make sure that the package contents, the required cables, tools,
and documentation are available. See Package contents below
• This network camera is intended to operate with PoE; if not available use AXIS PoE Midspan 1 port (not
included)
Package contents
1. “Package contents” on page 3
2. “Hardware overview” on page 4
3. “Mount the camera” on page 5
4. “Assign an IP address” on page 6
5. “Set the password” on page 9
6. “Adjust the Lens” on page 10
7. “Complete the installation” on page 10
Item Models/variants/notes
Network camera AXIS P3343
AXIS P3343 -V
AXIS P3344
AXIS P3344-V
Dome covers Clear transparent cover
Smoked transparent cover
Labels 2 adhesive serial no. labels
Mounting kit Resitorx screw driver, drill template, 2 screws and plugs, I/O connector block
CD AXIS Network Video Product CD, including product documentation,
installation tools and other software
Printed materials Installation Guide (this document)
Axis Warranty Document
Optional accessories Mounting bracket (region specific)
See ww.axis.com for information on available accessories

Page 4 AXIS P3343/P3343-V/P3344/P3344-V Installation Guide
Hardware overview
Network connector
LED indicators
Control button
Camera unit
I/O connector
(PoE)
Camera unit
Network cable
Dome cover
Audio
out Audio
in
Wall screws

AXIS P3343/P3343-V/P3344/P3344-V Installation Guide Page 5
ENGLISH
Mount the camera
The AXIS P3343/P3343-V/AXIS P3344/P3344-V can be mounted with the cables routed through or
along the wall. This product can also be fitted with a metal conduit for protecting the cabling when
they are routed along the wall. See the illustration below.
Mount the camera directly onto the wall
1. Using the drill template drill 2 holes in the wall.
2. Route and connect all required cables. Required cables include the network cable and may
include external input/output devices and the active speaker/external microphone.
3. Attach the camera unit to the wall using screws and plugs appropriate for the wall material.
Mount the camera using a mounting bracket (not included)
1. Using the drill template drill 2 holes in the wall.
2. Route all required cables through the wall and through the holes in the mounting bracket.
Required cables include the network cable and may include external input/output devices and
the active speaker/external microphone.
3. Attach the mounting bracket to the wall, using screws and plugs appropriate for the wall
material.
4. Connect cables.
5. Attach the camera unit to the mounting bracket using the two M4x8 screws provided.
Note: These instructions are for mounting the camera on a wall. The mounting bracket can also be used
for mounting the network camera to a junction box.
Network cable
Wall screw
M4x8 screw
Network cable
Wall screws
Metal conduit
(Optional/not included)

Page 6 AXIS P3343/P3343-V/P3344/P3344-V Installation Guide
Assign an IP address
The network camera is designed for use on an Ethernet network and requires an IP address for
access. Most networks today have a DHCP server that automatically assigns IP addresses to
connected devices. If your network does not have a DHCP server, the network camera will use
192.168.0.90 as the default IP address.
AXIS IP Utility and AXIS Camera Management are the recommended methods for setting an IP
address in Windows. These free applications are available on the Axis Network Video Product CD
supplied with this product, or they can be downloaded from www.axis.com/techsup Depending on
the number of cameras you wish to install, use the method that suits you best.
Note: If you are unable to set the IP address, check for any firewall blocking the operation.
See page 11 for other available methods for setting or discovering the IP address of the network
camera, in relation to other operating systems.
Method Recommended for Operating system
AXIS IP Utility
See page 7
Single camera
Small installations
Windows
AXIS Camera Management
See page 8
Multiple cameras
Large installations
Installation on a different subnet
Windows 2000
Windows XP Pro
Windows 2003 Server
Windows Vista

AXIS P3343/P3343-V/P3344/P3344-V Installation Guide Page 7
ENGLISH
AXIS IP Utility - single camera/ small installation
AXIS IP Utility automatically discovers and displays Axis devices on your network. You can also
manually set a static IP address through this application. AXIS IP Utility is available on the Axis
Network Video Product CD, or it can be downloaded from www.axis.com/techsup
Note that you must install the network camera on the same network segment (physical subnet) as
the computer running AXIS IP Utility.
Automatic discovery
1. Check that the network camera is connected to the network and that power has been applied.
2. Start AXIS IP Utility.
3. When AXIS P3343/AXIS P3344 appears in the window, double-click to open the camera’s home
page.
4. See page 9 for instructions on how to set the password.
Set the IP address manually (optional)
1. Acquire an unused IP address on the same network segment your computer is connected to.
2. Select the network camera in the list.
3. Click the button Assign new IP address to selected device - and enter the serial number
and IP address for the network camera. The serial number is located on the product label.
4. Click the Assign button and follow on-screen instructions. Note that the camera must be
restarted within two minutes for the new IP address to be set.
5. Click the Home Page button to access the camera’s web pages.
6. See page 9 for instructions on how to set the password.

Page 8 AXIS P3343/P3343-V/P3344/P3344-V Installation Guide
AXIS Camera Management - multiple cameras/large
installations
AXIS Camera Management can automatically discover multiple Axis devices, show connection
status, manage firmware upgrades and set IP addresses.
Automatic discovery
1. Check that the camera is connected to the network and that power has been applied.
2. Start AXIS Camera Management. When the camera appears in the window, right-click the link
and select Live View Home Page.
3. See page 9 for instructions on how to set the password.
Assign an IP address in a single device
1. Select AXIS P3343/P3344 in AXIS Camera Management and
click the Assign IP button .
2. Select Assign the following IP address and enter the IP
address, the subnet mask, and default router the device will
use.
3. Click OK.
Assign IP addresses in multiple devices
AXIS Camera Management speeds up the process of assigning IP
addresses to multiple devices, by suggesting IP addresses from a
specified range.
1. Select the devices you wish to configure (different models can be
selected) and click the Assign IP button .
2. Select Assign the following IP address range and enter the range
of IP addresses, the subnet mask, and default router the devices will use.
3. Click the OK button.

AXIS P3343/P3343-V/P3344/P3344-V Installation Guide Page 9
ENGLISH
Set the password
To gain access to the product, the password for the default administrator user root must be set. This
is done in the Configure Root Password dialog, which is displayed when the network camera is
accessed for the first time.
To prevent network eavesdropping when setting the root password, this can be done via an
encrypted HTTPS connection, which requires an HTTPS certificate.
To set the password via a standard HTTP connection, enter it in the Configure Root Password
window. To set the password via an encrypted HTTPS connection, follow these steps:
1. Click the Create self-signed certificate button.
2. Provide the requested information and click OK. The certificate is created and the password can
now be set securely. All traffic to and from the network camera is encrypted from this point on.
3. Enter a password and then re-enter to confirm the spelling. Click OK. The password has now
been configured.
4. To log in, enter the user name “root” in the dialog as requested.
Note: The default administrator user name root cannot be deleted.
5. Enter the password as set above, and click OK. If the password is lost, the network camera must
be reset to the factory default settings. See page 12.
If required, click Yes to install AMC (AXIS Media Control), which allows viewing of the video stream
in Internet Explorer. You will need administrator rights on the computer to do this.
Note: To install AMC in Windows Vista, you must run Internet Explorer as administrator. Right-click the
Internet Explorer icon and select Run as administrator.
The Live View page of the network camera appears. The Setup link to the right gives you menu
options that allow you to customize the camera.
To configure the password directly
via an unencrypted connection, enter
the password here.
To create an HTTPS connection, start
by clicking this button.

Page 10 AXIS P3343/P3343-V/P3344/P3344-V Installation Guide
Adjust the Lens
Open the Live View page in the web interface and
make the following adjustments to the camera:
1. Loosen the locking screw and tilt adjustment
screws.
2. Turn the lens (with the lens holder) to the
desired position. Make sure the horizon lines
on either side of the lens are aligned
horizontally and the single slit between the
horizon lines is pointing down.
3. Once satisfied, gently tighten the locking
screw and tilt adjustment screws to secure the
camera’s position.
4. Open the Focus Adjustment page in the Web interface under Basic Configuration > Focus &
Zoom, and follow the on-screen instructions. Use the image window to adjust the focus and
zoom.
Note: Due to the dome’s refraction, the image may appear slightly out of focus once the dome has been
placed. To correct this go to the focus page in the Web interface under Basic Configuration>Focus
& Zoom, and adjust the focus again.
Complete the installation
1. If the cables are routed along the wall, remove the side lid from the camera’s dome cover.
2. Rotate the black protective shield inside the dome casing to match the camera’s position.
3. Clean the dome with a dry soft cloth to remove dust and finger prints and use a blower to
remove dust from the lens.
4. Mount the dome casing using the supplied tamper-proof screws and screw driver. Now that the
dome is in place, check that the camera is properly focused.
The installation is now complete.
Locking screw
Tilt adjustment screw Tilt adjustment screw
Horizon line
This part
must face down

AXIS P3343/P3343-V/P3344/P3344-V Installation Guide Page 11
ENGLISH
Other methods of setting the IP address
The table below shows the other methods available for setting or discovering the IP address. All
methods are enabled by default, and all can be disabled.
Set the IP address with ARP/Ping
1. Acquire a free static IP address on the same network segment your computer is connected to.
2. Locate the serial number (S/N) on the camera’s label.
3. Open a command prompt on your computer and enter the following commands:
4. Check that the network cable is connected to the network camera and then start/restart the
network camera, by disconnecting and reconnecting power. If PoE is used, start/restart the
network camera by disconnecting and then reconnecting the network cable.
5. Close the command prompt when you see ‘Reply from 192.168.0.125:...’ or similar.
6. In your browser, type in http://<IP address> in the Location/Address field and press Enter on
your keyboard.
Notes:
• To open a command prompt in Windows: from the Start menu, select Run... and type cmd. Click OK.
• To use the ARP command on a Mac OS X, use the Terminal utility in Application > Utilities.
Use in operating
system
Notes
UPnP™
Windows When enabled on your computer, the camera is automatically
detected and added to “My Network Places.”
Bonjour MAC OSX
(10.4 or later)
Applicable to browsers with support for Bonjour. Navigate to the
Bonjour bookmark in your browser (e.g. Safari) and click on the
link to access the camera’s web pages.
AXIS Dynamic DNS
Service
All A free service from Axis that allows you to quickly and simply
install your camera. Requires an Internet connection with no
HTTP proxy. See www.axiscam.net for more information.
ARP/Ping All See below. The command must be issued within 2 minutes of
connecting power to the camera.
View DHCP server
admin pages
All To view the admin pages for the network DHCP server, see the
server’s own documentation.
Windows syntax Windows example
arp -s <IP Address> <Serial Number>
ping -l 408 -t <IP Address> arp -s 192.168.0.125 00-40-8c-18-10-00 ping -l 408 -t 192.168.0.125
UNIX/Linux/Mac syntax UNIX/Linux/Mac example
arp -s <IP Address> <Serial Number> temp
ping -s 408 <IP Address> arp -s 192.168.0.125 00:40:8c:18:10:00 temp ping -s 408 192.168.0.125

Page 12 AXIS P3343/P3343-V/P3344/P3344-V Installation Guide
Unit connectors
Network connector - RJ-45 Ethernet connector. Supports Power over Ethernet. Using shielded
cables is recommended.
Audio in - 3.5mm input for a mono microphone, or a line-in mono signal (left channel is used from
a stereo signal).
Audio out - Audio output (line level) that can be connected to a public address (PA) system or an
active speaker with a built-in amplifier. A pair of headphones can also be attached. A stereo
connector must be used for the audio out.
I/O terminal connector - Used in applications for e.g. motion detection,
event triggering, time lapse recording and alarm notifications. It provides the
interface to:
• 1 transistor output - For connecting external devices such as
relays and LEDs. Connected devices can be activated by the
VAPIX Application Programming Interface (API), by the output buttons on the Live View
page or by an Event Type. The output will show as active (shown under Event Configu-
ration > Port Status) if the alarm device is activated.
• 1 digital input - An alarm input for connecting devices that can toggle between an
open and closed circuit, for example: PIRs, door/window contacts, and glass break
detectors. When a signal is received the state changes and the input becomes active
(shown under Event Configuration > Port Status).
• Auxiliary power and GND
Function Pin Notes Specifications
GND 1 Ground
3.3V DC
Power
2 Can be used to power auxiliary equipment.
Note: This pin can only be used as power out.
Max. load = 50mA
Digital
Input
3 Connect to GND to activate, or leave floating (or
unconnected) to deactivate.
Min. input= - 40V DC
Max. input= + 40V DC
Digital
Output
4 Uses an open-drain NFET transistor with the source
connected to GND. If used with an external relay, a
diode must be connected in parallel with the load,
for protection against voltage transients.
Max. load = 100mA
Max voltage = + 40V DC
Pin1
Pin2
Pin3
Pin4

AXIS P3343/P3343-V/P3344/P3344-V Installation Guide Page 13
ENGLISH
The following connection diagram gives an example of how to connect an auxiliary device to the
AXIS P3343/P3343-V/P3344/P3344-V.
LED indicators
LED Color Indication
Network Green Steady for connection to a 100 Mbit/s network. Flashes for network activity.
Amber Steady for connection to 10 Mbit/s network. Flashes for network activity.
Unlit No network connection.
Status Green Steady green for normal operation.
Amber Steady during startup, during reset to factory default or when restoring settings.
Red Slow flash for failed upgrade.
Power Green Normal operation.
Amber Flashes green/amber during firmware upgrade.
1
2
E.g. push button
3
4
3.3V
max. 50mA
D
S
G

Page 14 AXIS P3343/P3343-V/P3344/P3344-V Installation Guide
Resetting to the Factory Default Settings
This will reset all parameters, including the IP address, to the Factory Default settings:
1. Disconnect power from the camera.
2. Press and hold the Control button (see Hardware Overview on page 4) and reconnect power.
3. Keep the Control button pressed until the Power indicator flashes amber (this may take up to15
seconds).
4. Release the Control button. When the Power indicator displays green (which can take up to 1
minute) the process is complete and the camera has been reset.
5. Re-assign the IP address, using one of the methods described in this document.
It is also possible to reset parameters to the original factory default settings via the web interface.
For more information, please see the online help or the user’s manual.
Accessing the camera from the Internet
Once installed, your network camera is accessible on your local network (LAN). To access the
camera from the Internet, network routers must be configured to allow incoming traffic, which is
usually done on a specific port
• HTTP port (default port 80) for viewing and configuration
• RTSP port (default port 554) for viewing H.264 video streams
Please refer to the documentation for your router for further instructions. For more information on
this and other topics, visit the Axis Support Web at www.axis.com/techsup
Further information
The user’s manual is available from the Axis Web site at www.axis.com or from the Axis Network
Video Product CD supplied with this product.
Tip!
Visit www.axis.com/techsup to check if there is updated firmware available for your AXIS product.
To see the currently installed firmware version, see Setup > About in your web interface.

AXIS P3343/-V/ AXIS P3344/-V Guide d’installation Page 15
FRANÇAIS
AXIS P3343/P3343-V/AXIS P3344/P3344-V
Guide d’installation
Procédez comme suit pour installer la caméra réseau :
Remarques :
• Avant de commencer, vérifiez le contenu de l’emballage et assurez-vous que l’alimentation, les câbles,
et la documentation sont disponibles. Voir Contenu de l'emballage ci-dessous
• Cette caméra réseau est conçue pour fonctionner avec un connecteur réseau (PoE), si vous n'en disposez
pas, utilisez AXIS PoE Midspan à 1 port (non inclus)
Contenu de l'emballage
1. « Contenu de l'emballage » à la page 15
2. « Description du matériel » à la page 16
3. « Montage de la caméra » à la page 17
4. « Attribution d’une adresse IP » à la page 18
5. « Configuration du mot de passe » à la page 21
6. « Réglage de l’objectif » à la page 23
7. « Terminez l’installation » à la page 23
Article Modèles/variantes/remarques
Caméra réseau AXIS P3343
AXIS P3343 -V
AXIS P3344
AXIS P3344-V
Bulle du dôme Bulle transparente non fumée
Bulle transparente fumée
Étiquettes Deux étiquettes adhésives portant le numéro de série
Kit de montage Tournevis Resitorx, gabarit de perçage, 2 vis et chevilles, bloc de connexion
E/S
CD CD de la caméra vidéo sur IP Axis comprenant la documentation,
les outils d’installation et les autres logiciels
Documentation Guide d’installation (le présent document)
Document de garantie d’Axis
Accessoires en option Support de fixation (spécifique à la région)
Pour des informations sur les accessoires disponibles, reportez-vous sur le
site www.axis.com

Page 16 AXIS P3343/-V/ AXIS P3344/-VGuide d'installation
Description du matériel
Connecteur réseau Témoins DEL
Bouton de commande
Caméra
Connecteur E/S
(PoE)
Caméra
Câble réseau
Bulle du dôme
Audio
sortie Audio
entrée
Vis murales

AXIS P3343/-V/ AXIS P3344/-V Guide d’installation Page 17
FRANÇAIS
Montage de la caméra
La AXIS P3343/P3343-V/AXIS P3344/P3344-V peut être montée avec les câbles d'alimentation
acheminés à travers le mur ou le long du mur. Ce produit peut également être doté d’un conduit
métallique pour protéger le câblage lors d’un acheminement des câbles le long du mur.
Reportez-vous à l'illustration ci-dessous.
Montage de la caméra directement sur le mur
1. En vous servant du gabarit de perçage, percez 2 trous dans le mur.
2. Orientez et connectez tous les câbles nécessaires. Les câbles nécessaires comprennent le câble
réseau et peuvent inclure des dispositifs d'entrée sortie et le haut parleur actif/microphone
externe.
3. Fixez la caméra au mur à l'aide des vis et des chevilles appropriées.
Installez la caméra au moyen du support de fixation (non inclus)
1. En vous servant du gabarit de perçage, percez 2 trous dans le mur.
2. Acheminez tous les câbles à travers le mur et à travers les orifices du support de fixation. Les
câbles nécessaires comprennent le câble réseau et peuvent inclure des dispositifs d'entrée sortie
et le haut parleur actif/microphone externe.
3. Fixez le support de fixation au mur à l'aide des vis et des chevilles appropriées.
4. Raccordez les câbles.
5. Fixez la caméra au support de fixation à l'aide des deux vis M4x8 fournies.
Remarque : Ces instructions concernent l'installation de la caméra sur un mur. Le support de fixation peut
être utilisé pour monter la caméra réseau à un boîtier de jonction.
Câble réseau
Vis murale
Vis M4x8
Vis murales
Conduit métallique
(En option, non inclus)
Câble réseau

Page 18 AXIS P3343/-V/ AXIS P3344/-VGuide d'installation
Attribution d’une adresse IP
La caméra réseau AXIS P3343/P3343-V/ AXIS P3344/P3344-V est conçue pour une utilisation sur
un réseau Ethernet et nécessite une adresse IP pour y accéder. Aujourd’hui, la plupart des réseaux
sont équipés d’un serveur DHCP qui attribue automatiquement des adresses IP aux périphériques
connectés. Si votre réseau ne possède pas de serveur DHCP, la caméra réseau AXIS P3343/P3343-V/
AXIS P3344/P3344-V utilisera l’adresse IP 192.168.0.90 comme adresse IP par défaut.
Il est conseillé d’utiliser AXIS IP Utility et AXIS Camera Management pour configurer une adresse IP
sous Windows. Ces deux applications gratuites sont disponibles sur le CD de la caméra vidéo sur IP
Axis joint à votre produit. Vous pouvez également les télécharger à partir du site
www.axis.com/techsup. Selon le nombre de caméras à installer, choisissez la méthode qui vous
convient le mieux.
Remarque : Si vous n’arrivez pas à configurer l’adresse IP, vérifiez qu’aucun pare-feu ne bloque
l’opération.
Pour connaître les autres méthodes de configuration ou de détection de l’adresse IP de la caméra
réseau AXIS P3343/P3343-V/ AXIS P3344/P3344-V sous d’autres systèmes d’exploitation,
reportez-vous à la page 24.
Méthode Recommandée pour Système
d’exploitation
AXIS IP Utility
Voir page 19
Une seule caméra
Petites installations
Windows
AXIS Camera Management
Voir page 20
Plusieurs caméras
Grandes installations
Installation sur un autre
sous-réseau
Windows 2000
Windows XP Pro
Windows 2003 Server
Windows Vista

AXIS P3343/-V/ AXIS P3344/-V Guide d’installation Page 19
FRANÇAIS
AXIS IP Utility - Une seule caméra/petite installation
AXIS IP Utility recherche et affiche automatiquement les périphériques Axis sur votre réseau. Vous
pouvez également configurer manuellement une adresse IP statique avec cette application. AXIS IP
Utility est disponible sur le CD de la caméra vidéo sur IP Axis. Vous pouvez également la télécharger
à partir du site www.axis.com/techsup.
Notez que vous devez installer la caméra réseau AXIS P3343/-V/ AXIS P3344/-V sur le même
segment de réseau (sous-réseau physique) que l’ordinateur exécutant l’application AXIS IP Utility.
Détection automatique
1. Vérifiez que la caméra réseau AXIS P3343/P3343-V/AXIS P3344/P3344-V est connectée au
réseau et que l’alimentation est activée.
2. Lancez AXIS IP Utility.
3. Double-cliquez sur l’icône de l’AXIS P3343/P3343-V/AXIS P3344/P3344-V lorsque celle-ci
apparaît dans la fenêtre. Vous accéderez ainsi à la page d’accueil de la caméra.
4. Reportez-vous à la page 21 pour savoir comment configurer le mot de passe.
Configuration manuelle de l’adresse IP (facultatif)
1. Trouvez une adresse IP non utilisée sur le même segment de réseau que celui de votre
ordinateur.
2. Sélectionnez AXIS P3343/P3343-V/AXIS P3344/P3344-V dans la liste.
3. Cliquez sur le bouton Assign new IP address to selected device (Attribuer une nouvelle
adresse IP au périphérique sélectionné) et saisissez l’adresse IP.
4. Cliquez sur le bouton Assign (Attribuer) et suivez les instructions qui s’affichent à l’écran. La
caméra doit être redémarrée dans les deux minutes pour que la nouvelle adresse IP soit prise en
compte.
5. Cliquez sur le bouton Home Page (Page d’accueil) pour accéder aux pages Web de la caméra.
6. Reportez-vous à la page 21 pour savoir comment configurer le mot de passe.

Page 20 AXIS P3343/-V/ AXIS P3344/-VGuide d'installation
AXIS Camera Management - Plusieurs caméras/grandes
installations
AXIS Camera Management peut détecter automatiquement plusieurs périphériques Axis, afficher
l’état de connexion, gérer les mises à niveau du micrologiciel et configurer les adresses IP.
Détection automatique
1. Vérifiez que la caméra est connectée au réseau et sous tension.
2. Lancez AXIS Camera Management. Lorsque la caméra apparaît dans la fenêtre, cliquez sur le
lien avec le bouton droit de la souris et sélectionnez Live View Home Page (Page d’accueil –
Vidéo en direct).
3. Reportez-vous à la page 21 pour savoir comment configurer le mot de passe.
Attribution d’une adresse IP à un seul périphérique
1. Sélectionnez AXIS P3343/P3343-V/AXIS P3344/P3344-V dans
l’application AXIS Camera Management, puis cliquez sur le
bouton Assign IP(Attribuer une IP).
2. Sélectionnez Assign the following IP address (Attribuer
l’adresse IP suivante) et saisissez l’adresse IP, le masque de
sous-réseau et le routeur par défaut que le périphérique utilisera.
3. Cliquez sur OK.