Aydin Displays CFP32W1 Large Screen Series User manual

CAMBRIDGE
USERS MANUAL
CFP32W1 Large Screen Series
LCD Monitor User Guide
Document No. 150-CFP-320

150-CFP-320 Page 2
Contents
Important Safety Instructions ………………………………………………... 3
 Safety Precautions …………………………………………………………………...…… 3
 Installation ………………....………………………………………………………….…… 4
 Use Caution ……………………………….………………………………………………… 5
 Keeping Your Display Clean ……………….…………………………………….…………5
Features………………………………………………………………….……........ 5
Package Contents ……….....…………………….……………………………... 6
 Dimension ……………………………………………………………………………….… 8
 Installation ……………………………………………………………………………….… 9
 Power Input …………….…….………………………………………………………….… 9
 Power Interface ………..…….………………………………………………………….… 9
 Connection …………….…..……….……………………..…………………………….… 10
 Single Source Input ………….……………………………………………….................. 10
Operating The Monitor …….…………….……………………………............... 11
 The Side Controller Of The Monitor ……….....……………………..….…………….… 11
 The Remote Controller(RCU) Instructions ……………..…………………………….… 11
 Change The RCU Battery ………………..….………………………….……………..… 12
 Display Mode ……..…………………..………… ……………….……………..… 12
 OSD Menu Function ……..…………………..………………………….……………..… 14
 OSD Operating ……………..……………..….………………………….……………..… 15
Default Setting …………………………………………………………….……... 17
Support Timing …………..…………………………….………………….……... 18
Specification …………..……………….………................................................ 19
Troubleshooting …………………………………….……….…………………... 20
Compliance ……………………………..…………………….…………………... 20
Appendix ………………………………..…………………….…………………... 21

※Please read this user’s manual cautiously and completely before operating this
monitor.
Important Safety Instructions
Before using the monitor, please read this user’s manual thoroughly to help protect against damage your own and
other people’s property and to ensure your own and other people personal safety.
 Be sure to observe the following instructions with understanding meaning below.
 For your safety, be sure to observe the warning in this manual.
 The installation or adjustment, please follow this manual instructions or refer all servicing to qualified service
personnel at Aydin Displays 610-404-7400.
Safety Precautions
If smoke or peculiar smell comes from the monitor, remove the power plug from the
outlet immediately.
If the monitor is still used in this condition, it may cause a fire or an electrical shock.
Contact Aydin Displays for a return authorization.
If there isn’t picture, remove the power plug from the outlet immediately.
If the monitor is still used in this condition, it may cause a fire or an electrical shock.
Contact Aydin Displays for a return authorization.
If water is spilled or objects are dropped inside the monitor, remove the power plug
from the outlet immediately.
If the monitor is still used in this condition, it may cause a fire or an electrical shock.
Contact Aydin Displays for a return authorization.
If the monitor is dropped or the cabinet is damaged, remove the power plug from the
outlet immediately.
If the monitor is still used in this condition, if may cause a fire or an electrical shock.
Contact Aydin Displays for a return authorization.
Turn off the power of the monitor, press “O” on the main power switch at the back
cover.
The power standby/on indicator goes off and the set cannot to be turned on/ off by using the POWER button on
the remote control. (To turn on/off the monitor by the remote control, press the main power switch again and
light the power standby/on indicator.)
 When turning off the monitor by pressing the POWER button on the remote control, the main power of the
monitor is not turned off completely.
 To disconnect the monitor completely from power supply, remove the power plug from the outlet.
Press”O”to turn off monitor completely
150-CFP-320 Page 3

150-CFP-320 Page 4
If the power cord or plug is damaged or becomes hot, turn off the main power switch of
the monitor, make sure the power plug has cooled down and remove the power plug
from the outlet .
If the monitor is still used in this condition, it may cause a fire or an electrical shock.
Contact Aydin Displays for a return authorization.
Installation (when install the monitor, please follow the instruction on the manual )
Don't install in the high-temperature environment.
If the monitor used in high-temperature or in direct sunlight, it may cause the case or other parts to be distorted or
damaged, overheating or an electric shock.
Don't install in the high-humidity environment such as a bathroom or close to a
humidifier.
This may cause overheating or an electric shock.
Don't install near any heat source such as radiators, heat registers, stoves, or other
apparatus that produce heat.
This may cause a fire or an electric shock.
Don't overload outlets or cables beyond electricity capacity.
Don't use extension cords, it may cause a fire or an electric shock.
Don't insert the power plug into an outlet other than 100~240V AC.
This may cause a fire or an electric shock.
 Don’t use a damaged power plug or worn outlet.
 Don’t insert the improper power plug may cause a fire and an electric shock.
Don't place the monitor on the unstable shelf or desk, such as a shaky table.
The monitor may fall down and cause injury damage. Please install on a horizontal, stable surface.
Don't place objects on the monitor.
 If the monitor is covered under the newspaper, tablecloth or curtain, the monitor vent could be clogged, and
it may make the monitor overheating and cause the fire.
 If metal or liquid (putting the vase, glass or the cosmetics) get into the monitor, it may cause a fire or an
electrical shock.
 If you put the heavy object on the monitor, it may fall down and cause the injury
 Please Keep 10cm minimum distance between the monitor and the wall for sufficient ventilation.
Don't move the monitor when it is connecting power cord and cables.
 When moving the monitor, make sure to take off the power plug and cables from the outlet or sync source. If not, a fire
and an electric shock may occur. If the power plug is damaged, injury may result from the monitor’s falling down.
 When unpacking or carrying the monitor, at least 2 people are needed. Make sure the monitor is upright.
 When moving or putting the monitor, avoiding to face the monitor up or down.
 Handle the monitor so as not to jolt the monitor.

150-CFP-320 Page 5
UseCaution
When having installation problems, contact Aydin Displays at 610-404-7400.
Protect and correctly use the power cord/ plug.
 Don't heavy press the power cord/ plug, don't step on the power cord/plug.
 Connect the power cord and the monitor before insert the power plug into the wall outlet.
 Don't operate the monitor with a damaged power cord, otherwise the monitor will be damaged.
Precautions for the remote control batteries..
 Please use the specified battery type CR2032 only.
 Please be sure to insert batteries by matching the ┼and─.
 Don’t recharge, heat, disassemble, short or throw batteries into a fire.
 Don’t mix a new battery with a used one.
 Don’t mix different types of batteries together (only use the specified type). Or, it may cause burn and injury.
Keeping Your Display Clean
If dust has collected on the power plug, remove the plug from the outlet and clean off
dust.
The dust may cause a fire due to the reduced insulation of the plug.
Take off the power plug before cleaning.
If not, it may cause an electric shock. Don’t involve the power cord and the plug from the outlet.
Otherwise, it may cause an electric shock.
Clean the surface of the monitor.
 When the surface of the monitor is polluted, please wipe the surface with the cotton or clean cloth lightly.
 If pollution is not easy to clean out, use the cloth with 50% of alcohol .
 Please notice carefully that not to let alcohol enter the monitor, it may cause electrical failures.
Features
High-resolution HD panel
This monitor supports 1360 x 768 WXGA format and can display true 16.7M colors, you can enjoy extreme fine
picture.
MVA system less-reflection black TFT LCD panel
MVA system and Black TFT LCD panel offer bright and wide images with clear contrast. Even placed near the
windows, the monitor shows bright and clear images with little reflection. The viewing angles of the monitor are as
wide as 170° both horizontally and vertically, enough to enjoy clear images at any view angle.
Offer varieties of connection
Video system Input:
There are 3 choices of connection RGB Input: There are 2 choices of connection Signal delivery
VIDEO RCA
S-VIDEO Mini Din 4 pin
COMPONENT Mini Din 8 pin
RGB ANALOG D-Sub 15pin
RGB DIGITAL DVI-ID 24pin
RS-232C in D-sub 9pin (Option)
RS485 in RJ-45 one port (Option)
RS485 out RJ-45 one port (Option)

Other functions
 PIP/ PAP function. Please see the chapter “Display mode”.
 Quick Adjustment- Volume & input source selection .Please see the chapter ”The side controller of
the monitor “&”OSD menu function”.
 Support 4 picture scene mode-standard, movie, vivid, user. Please see the chapter ”OSD Menu
Function “.
Package Contents
Unpacking
CFP32W1 is packed by the carton box. During transportation, in order to protect the monitor, CFP32W1 is packed
by cushions to be safe packaged and protected.
Before unpacking your monitor, prepare a stable, level, and clean surface near a wall outlet for your monitor first.
Set the LCD Monitor box in an upright position and open it from the top of the box before removing the top
cushions.
 Step 1: Remove the white handle and cut the bundle
150-CFP-320 Page 6

 Step 2: Remove the top cushion and take the accessories box out.
Top cushion
The Monitor
Accessories Box
Bottom cushion
Packing list
Q’ty Item Q’ty Item
1 set CFP32W1 1 pcs DVI-D 24 pin cable
1 pcs Power cord 1 pcs D-SUB 15pin cable
1 pcs User's manual 1 pcs S-VIDEO Mini Din 4 pin cable
1 pcs Remote controller 1 pcs Component Mini Din 8 pin cable
1 pcs RCA cable 1 pcs RS-232C D-sub 9pin cable (Option)
150-CFP-320 Page 7

Dimension (Front & Back)
150-CFP-320 Page 8

Installation
Environmental state
Operating temperature︰5℃ ~ 40℃ (Fahrenheit : 41℉ ~ 104℉)
Humidity︰max. 85%
Power Input
Power Cord
AC Power cord
This power cord is used to connect the side controls of the LCD monitor and the wall outlet.
Connect the power cord into main power of the monitor, and “│” is power on, “○”is power off.
Input : 100-240V~ 3A 50/60Hz
150-CFP-320 Page 9
Sin
g
le In
p
ut Interface
The side of control
│is power on
○is
p
ower off
Main power –Switch &
AC socket
Power Interface
 Main interface- switch & AC socket. Please see the chapter “Power input ”
 The side controller of the monitor
 The remote control (RCU )

Connection
 CVBS-Video (RCA ) input – support 480i input.
 S-Video input – support 480i input
 Component Y/Pb/Pr input – support 480i~720P input
 DVI(DVI-D) input – support timing, please see the chapter “Supported Timing”.
 RGB(VGA) input – support timing, please see the chapter “Supported Timing”.
 Audio in (RCA) input
 Audio out(RCA) output
 RS-232C input (option)
Single Source Input
Input Interface
NO. Name Remarks
1 Video-IN input connecter RCA
2 S-video input connecter Mini Din 4 pin
3 Y-Pb-Pr (Y-Cb-Cr) inputs Mini Din 8 pin
4 DVI input connecter DVI-D 24 pin
5 RGB input connecter D-Sub 15 pin
6 Audio in RCA jack x2 R/L
7 Audio out RCA jack x2 R/L
8 RS232C-IN input (option) D-Sub 9 pin
9 RS485-IN input (option) RJ-45
10 RS485-out output(option) RJ-45
Single Cable Input
The Video Signals Input
You can select Video input form 3 connections below:
Video signals Connection type Signal
Video RCA NTSC/PAL
S-Video 4 stitches NTSC/PAL
(Y Pb/Cb Pr/Cr) 8 stitches NTSC/PAL
150-CFP-320 Page 10

The RGB inputting
You can select RGB input and Video for 3 connections as below:
RGB signals Connection type Signal
RGB Analog VGA 15 pins RGB Analog
RGB Digital DVI-D DVI-D 24 pins RGB Digital
Signal delivery Connection type Signal
RS-232C(Option) 9 pin
RS485-IN input (option) RJ-45
RS485-out output(option) RJ-45
Operating The Monitor
TheSideControllerOfTheMonitor
No. Key Description
1 Power Power Switch ; Power ON/OFF
2 SOURCE Input source selection
3 ▲Menu up
4 ▼Menu down
5 eMenu left / Volume(Value) decrease
6 fMenu right / Volume(Value) increase
7 MENU/EXIT Enter OSD menu / Exit menu or select
The Remote Control (RCU ) Instructions
No. Key Description
1 POWER Power ON / OFF
2 WVolume decrease
3 Source Input source selection
4 PIP PIP function on/PIP selection S-M-L-POP
5 W(LEFT) Move left
6 S(UP) Move up
7 MENU/EXIT Call OSD menu/ Exit and one level up
8 XVolume increase
9 AUTO Adjust clock, phase, H & V position automatically
10 SWITCH PIP picture switch
11 X(RIGHT) Move right
12 T(DOWN) Menu down
1
2
3
4
5
6
7
8
9
10
11
12
150-CFP-320 Page 11

Change The RCU Battery (RCU option)
(1) (2)
(3)
i. Push down as picture (1) and pull the back cover.
ii. Replace with the new batteries as picture (2), 1 piece Lithium battery(CR2032) make sure the
polarities of batteries are correct.
iii. Place the back cover and slide it as in the picture (3).
iv. Used batteries needed to follow the city rule to be discarded.
v. Avoid keeping used, old batteries inside the remote control, causing leakage of internal liquid
resulting metal rust or fatal damage to the remote control hand unit.
vi. Battery to be used according to the instruction
CAUTION
 Risk of explosion if batty is replaced by an incorrect type.
 Dispose of used batteries according to the instructions.
About the remote controllers
 Please don’t drop, shake or bump.
 Please don’t place on wet materials.
 Please don't dismantle.
 Please don’t place in locations exposed to high-temperature or high-humidity levels.
DisplayMode
Main Source mode
The main source mode will be changed in the sequence as follows: VGA/DVI/ AV(Composite) / S-Video/
YPbPr(Component) by remote control or the “source” key of the monitor.
PIP(sub source) mode
Please select PIP input source(function) form the PIP button on the remote controller. There is no PIP button on
side controller of the monitor.
The sub-source changes as the main source changes. (picture 1)
150-CFP-320 Page 12

Display ID
number
Main source
Sub source
00 PC
H: 48.2KHz
V: 59.8 Hz
Current source
<Picture 1>
150-CFP-320 Page 13

OSD (On Screen Display) Menu Function
Main Menu Sub-Menu Description Setting
Contrast Adjust the contrast of the screen 0~100
Brightness Adjust the brightness of the screen 0~100
Hue Adjust the picture hue of the screen 0~100
Saturation Adjust the picture saturation of the screen 0,100
Color-Tone Adjust 3 kinds of the picture tone of the screen 6500,5400,9300
Scale Select 4 kinds of the picture ratio. Full,Zoom1,Zoom2,Normal
Picture
(Video mode)
Picture Mode Select 4 kinds of the picture scene mode Standard,Movie,vivid,user
Volume Adjust the volume of the audio 0~100
150-CFP-320 Page 14
Bass Adjust the bass of the audio 0~100
Treble Adjust the treble of the audio 0~100
Sound
Balance Adjust the balance of the audio 0~100
Set Display ID Set ID number of Display 00~255
H-Position Adjust the H-position of PIP 0~100
V-Position Adjust the V-position of PIP 0~100
Border Color Select the PIP border color Blue,Black
Function Multi-Picture
Swap Swap main & sub source Select
Contrast Adjust the contrast of the screen 0~100
Brightness Adjust the brightness of the screen 0~100
H-Position Move the picture left/right on the screen 0~100
V-Position Move the picture up/down on the screen 0~100
Clock Adjust the display clock 0~100
Phase Adjust the display phase 0~100
Select 5 kinds of the color temperature setting sRGB,User,6500K
5400K,9300K
Red Adjust the Red color of user mode 0,100
Green Adjust the Green color of user mode 0,100
Color Mode
Blue Adjust the Blue color of user mode 0,100
PC
(RGB mode)
AUTO Auto adjustment Select
Language Language setting English
H-Position Adjust the OSD menu H-position 0~100
V-Position Adjust the OSD menu V-position 0~100
Duration Adjust the OSD menu duration 0~60
Half tone Adjust the OSD menu tone 0~100
Information Display resolution Select
OSD
Memory recall Reset to the factory default setting Select
QuickAdjustment:
 Volume decreasing => Press “ e ”on the side controller of the monitor
 Volume increase => Press “
X ” on the side controller of the monitor
 Input source select => press “Source” on the side controller of the monitor
 Picture scene mode select=> Quick select picture scene mode-Standard,Movie,vivid,user
Depending on your selection may not always produce the desired results. If results are not to your
satisfaction, please try to adjust contrast/brightness/hue/ Saturation/color tone. But when you
choose another picture scene mode, the value you adjust will be lost.

OSDOperating
Structure of OSD Menus
Press”▼” to select
OSD menu item
Press”X” to enter OSD
submenu.
Press “MENU/EXIT” to
enter or exit OSD menu
Press “X”or ”W” to adjust
the value
Press “X”or ”W” to select
the setting
λ Picture : OSD color is yellow
 On side of controller:
Press “MENU/EXIT” to enter the OSD menu
Press“X” to enter Picture setting
Press”▼” to select the Contrast, Brightness, HUE,
Saturation, Color Tone, Scale, Picture setting
Press“X” or “W”to adjust the value or select the Color Tone,
Scale, Picture Mode setting.
Press“MENU/EXIT” to exit the OSD menu.
 On RCU:
Press “MENU/EXIT” to enter the OSD menu
Press“X” to enter Picture setting
Press”▼” to select the Contrast, Brightness, HUE,
Saturation, Color Tone, Scale, Picture setting.
Press“X” or “W”to adjust the value or select the Color Tone,
Scale, Picture Mode setting.
Press“MENU/EXIT” to exit the OSD menu.
λ Sound : OSD color is Orange
150-CFP-320 Page 15
 On side of controller:
Press “MENU/EXIT” to enter the OSD menu
Press”▼” and then press “X”to select Sound setting.
Press”▼” to select the Volume, Bass, Treble, Balance setting
Press“X” or “W”to adjust the value.
Press“MENU/EXIT” to exit the OSD menu.
 On RCU:
Press “MENU/EXIT” to enter the OSD menu
Press”▼” and then press “X”to select Sound setting.
Press”▼” to select the Volume, Bass, Treble, Balance setting
Press“X” or “W”to adjust the value.
Press“MENU/EXIT” to exit the OSD menu.

λ Function : OSD color is Green
 On side of controller:
Press “MENU/EXIT” to enter the OSD menu
Press”▼” twice and then press “X”to select Function setting.
Press”▼” to select the Set Display ID, Multi Picture setting
Press“X” or “W”to adjust ID number or select Multi Picture
the setting.
Press“MENU/EXIT” to exit the OSD menu.
 On RCU:
Press “MENU/EXIT” to enter the OSD menu
Press”▼” twice and then press “X”to select Function setting.
Press”▼” to select the Set Display ID, Multi Picture setting.
Press“X” or “W”to adjust ID number or select Multi Picture
the setting.
Press“MENU/EXIT” to exit the OSD menu.
λ PC : OSD color is Red
 On side of controller:
Press “MENU/EXIT” to enter the OSD menu
Press”▼” three times and then press “X”to select PC setting.
Press”▼” to select the Contrast, Brightness, H-Position
,V-Position, Clock, Phase, Color Mode, Auto setting
Press“X” or “W”to adjust the value or select the Color Mode
setting
Press“MENU/EXIT” to exit the OSD menu.
 On RCU:
Press “MENU/EXIT” to enter the OSD menu
Press”▼” three times and then press “X”to select PC setting.
Press”▼” to select theContrast, Brightness, H-Position
,V-Position, Clock, Phase, Color Mode, Auto setting.
Press“X” or “W”to adjust the value or select the Color Mode
setting
Press“MENU/EXIT” to exit the OSD menu.
OSD : OSD color is Brown
 On side of controller:
Press “MENU/EXIT” to enter the OSD menu
Press”▼” four times and then press “X”to select OSD setting.
Press”▼” to select the Language, H-Position, V-Position
, Duration, Halftone, Information, MemoryRecall setting
Press“X” or “W”to adjust the value or select the Information
setting.
Press“MENU/EXIT” to exit the OSD menu.
150-CFP-320 Page 16
 On RCU:
Press “MENU/EXIT” to enter the OSD menu
Press”▼” four times and then press “X”to select OSD setting.
Press”▼” to select the Language, H-Position, V-Position
, Duration, Halftone, Information, MemoryRecall setting.
Press“X” or “W”to adjust the value or select the Information
setting.
Press“MENU/EXIT” to exit the OSD menu.

150-CFP-320 Page 17
Default Setting
Item Default
Power switch Off
Brightness 80
Contrast 50
Color temp. User
Red 50
Green 50
Blue 50
Language English
Auto Adjust On

Supported Timing
Sync
polarity Horizontal (dot) Vertical (line)
Item
Video Mode fH
(kHz) fV (Hz)
Dot
clock
(MHz) H V A B C D E O P Q R S
Analog
Digital
Componen t
1 31.469 59.940 25.175 N N 800 96 48 640 16 526 2 33 480 11 O O
2 37.861 72.809 31.500 N N 832 40 128 640 24 520 3 28 480 9 O O
3
VGA 640x480
37.500 75.000 31.500 N N 840 64 120 640 16 500 3 16 480 1 O O
4 35.156 56.250 36.000 P P 1024 72 128 800 24 625 2 22 600 1 O O
5 37.879 60.317 40.000 P P 1056 128 88 800 40 628 4 23 600 1 O O
6 48.077 72.188 50.000 P P 1040 120 64 800 56 666 6 23 600 37 O O
7
SVGA 800x600
46.875 75.000 49.500 P P 1056 80 160 800 16 625 3 21 600 1 O O
8 48.363 60.004 65.000 N N 1344 136 160 1024 24 806 6 29 768 3 O O
9 56.476 70.069 75.000 N N 1328 136 144 1024 24 806 6 29 768 3 O O
10
VESA
XGA 1024x768
60.023 75.029 78.750 P P 1312 96 176 1024 16 800 3 28 768 1 O O
11 640x480 35.000 66.667 30.240 N N 864 64 96 640 64 525 3 39 480 3 O O
12 832x624 49.725 74.500 57.283 N N 1152 64 224 832 32 667 3 39 624 1 O O
13
Macintosh
1024x768 60.150 74.720 80.000 N N 1330 96 168 1024 42 805 3 31 768 3 O O
14 WXGA 1360x768 47.72 59.95 84.75 P P 1776 152 176 1360 88 796 3 24 768 1 O O
15 37.50 50.000 74.250 N N 1980 40 220 1280 440 750 5 20 720 5 O O
16 44.96 59.94 74.18 P P 1650 40 220 1280 110 750 5 20 720 5 O O
27
720p 1280x720
45.00 60.00 74.25 P P 1650 40 220 1280 110 750 5 20 720 5 O O
fH
Item
Video Mode
(kHz) fV (Hz)
Dot
clock
(MHz)
Analog Composite S-Video Component
1 480i NTSC 358-443 15.743 59.94 16.521 O O O
2 576i PAL SECAM 15.625 50.00 16.406 O O O
3 480P 720X480 31.542 60.08 27.00 O
4 576P 768X576 31.25 50 28.812 O
150-CFP-320 Page 18

150-CFP-320 Page 19
Specification
Item Specification Unit
Pixel Number 1366x R.G.B. x 768 pixel
Pixel Arrangement RGB Vertical Stripe -
Resolution 1360x768@60Hz(Max)
Display Color 16.7M color
Trans-missive Mode Normally Black -
ViewingAngle (H / V) 176 / 176 degree
Brightness 500 (typ.) cd/m2
Contrast Ratio 1200(typ.) -
LCD panel
Response Time 6.5 (Gray to Gray, typ.) msec
Separate Sync. LVDS Level -
Horizontal Sync. Positive / Negative -
Vertical Sync. Positive / Negative -
Graphic
Input Connector D-Sub 15 pins, DVI-D 24 pins, Component
Composite, S-Video, RS-232C(option) -
Auto Adjust Clock, Phase, H Position & V Position -
Screen Scaling VGA/SVGA/XGA/SXGA/WXGA
Full Screen Display -
Power Management VESA DPMS, DVI DMPM -
Color Adjustment User,6500K,5400K,9300K -
OSD Language English -
PIP 4 size; Small/Middle/Large/PAP
Performance
Video mode display ratio Full,Zoom1,Zoom2,Normal
Power supply Input AC AC 100 ~ 240(Worldwide) V
Operation Mode 180 (Max) W
Power consumption Power Saving Mode 22W(Max) W
Dimension, (WxDxH) 790.2 x 99.7x 480.2(w/o stand) mm,
Net Weight 16.5 kg
Physical
Gross Weight 20 kg
Function OSD key 7 keys
【Power;source; ▲,T,W,XMenu/Exit】key
Wall mount VESA standard 200x 200,100x 100 mm

150-CFP-320 Page 20
Troubleshooting
Before calling service personnel, please check the following chart for a possible cause to the trouble you are
experiencing.
 Perform the adjustments according to Operation The Monitor
 Refer to the following items if you can’t find a proper item listed in the Operating the Monitor or if the problem
remain.
 if the problem you have experienced isn’t described below or you can’t correct the problem, stop using the
monitor and please call service personnel or your dealer.
Problem Check these things
No Display Check the power plug inserted on the wall outlet..
Check the main power switch
If AC socked is OK, please try to use another set of the equipment.
Check the input single, the signal may not be suitable.
Display is not in the center. If the signal timing of the computer is within the spec.
Display is shaking. If the signal timing of the computer is within the spec.
The remote control doesn’t work Make sure the battery is inserted matching the + and – marks of the
battery compartment.
The battery may be exhausted..
Use the remote control aiming at the remote control sensor.
The picture color is pale, or not clear Check picture quality to adjust.
If you are using YUV terminals, make sure cables are correctly connected.
Compliance
FCC Compliance Statement:
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Warning
This is class A products. In a domestic environment this product may
Cause radio interference in which case the user may be required to take adequate
measures.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions : (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference
that may cause undesired operation.
CE
EN 55022、EN 61000-3-2、EN-61000-3-3
EN 55024、IEC61000-4
EN 60950 [Low-Voltage Directive (73/23/EEC)]