Azden SGM-2X User manual

SGM-2X
INSTRUCTIONS
DUAL-BARREL
PROFESSIONAL SHOTGUN MICROPHONE
© 2007 Azden Corporation P1040-01 012-34136-01B
Printed in Japan
Customers in the Asian and Oceania markets contact:
Azden Corp., 1-12-17 Kamirenjaku Mitaka-shi, Tokyo, 181-8533 Japan
voice - 81-1-422-55-5115(Japan) • fax - 81-1-422-55-0131(Japan)
email - [email protected]
Azden Corporation warrants, to the first purchaser, that the Azden brand product
purchased is free from defects in material and workmanship. Azden's sole obligation
under this warranty shall be to provide, without charge, repair or replacement
(at Azden's option), within two years from the date of purchase. A dated receipt acts
to establish the date of purchase.
This warranty is the sole and exclusive express warranty given with respect to the
product and all other express warranties are herby excluded. Neither AZDEN, nor
the dealer who sells this product, is responsible for indirect, incidental or consequential
damages. Some states do not allow the exclusion or limitation of incidental or
consequential damages, so the above limitation may not apply to you.
This warranty does not extend to any defect, malfunction or failure caused by misuse,
abuse, accident, faulty hookup, unauthorized modification or defective associated
equipment for which it is not intended. Please read your owner's manual carefully.
This warranty gives you specific legal rights. You may also have other rights which
vary from state to state.
To register this product, go to www.azdencorp.com/warranty "for North/South
America and EU customers.
Asia/Oceania customers contact with Azden distributors listed on www.azden.co.jp/global.html
TWO-YEAR WARRANTY
Customers in the North/South America and Europian markets contact:
Azden Corp., 200 Valley Road, Suite 101, Mt. Arlington, NJ 07856
voice - 973-810-3070 • fax - 973-810-3076 • email - [email protected]

Frequency Response Super-Cardioid Polar Pattern
-80
-75
-70
-65
-60
-55
-50
-45
-40
-35
-30
20 50 100 200 500 1k 2k 5k 10k 20k
0゜
90゜
270゜ 0.50.5
180゜
0.5
0.5
1KHz
250Hz
4KHz
0゜
90゜
180゜
Thank you for purchasing the Azden SGM-2X microphone. Designed for Video and Audio
Professionals, the SGM-2X comes with 2 barrels that effectively change the pick-up pattern of
the microphone. With the short barrel the SGM-2X works as a sensitive omni-directional
microphone. By attaching the supplied long barrel the SGM-2X becomes a directional super-
cardioid shotgun microphone. In either configuration the SGM-2X exhibits a wide frequency
response and low noise levels.
BATTERY:
The SGM-2X is powered by 1 “AAA” battery (not included). Unscrew the lower half of the short
barrel case just below the “Power” switch by turning it counter-clockwise. Install 1 fresh “AAA”
Alkaline battery, making sure to check polarity, and close the case by turning it clockwise. DO
NOT OVER-TIGHTEN or you may strip the threads.
MICROPHONE BARRELS:
Two microphone barrels and windscreens are supplied with the SGM-2X. The SHORT barrel
has a wide omni-directional pick-up pattern. By attaching the LONG barrel to the SHORT
barrel the microphone has a super-cardioid pick-up pattern. This narrow or directional pattern
rejects side and back noise and lets you focus in on your subject. In either configuration use
the appropriate windscreen for best results.
NOTE:
A CAPSULE COVER is attached to the SHORT barrel before shipping. This CAPSULE
COVER should be attached to the SHORT barrel when using the SGM-2X as an omni-
directional microphone. To use the SGM-2X as a shotgun microphone, first remove the
CAPSULE COVER from the SHORT barrel by turning it counter-clockwise until it comes off,
then attach the LONG barrel to the SHORT barrel turning it clockwise until tight. DO NOT
OVER-TIGHTEN.
SHOCK-MOUNT HOLDER:
The SGM-2X is supplied with a shock-mount holder. This holder can be used on a camera
shoe or on a microphone stand. Push the SHORT barrel through the center of the elastic
bands until it is positioned as shown. To secure the holder to a camera shoe, slide the holder
into the camera shoe and tighten the thumbwheel by turning it clockwise. To secure the holder
to a microphone stand, screw the holder to the stand by turning it clockwise until it is tight.
NOTE: Two holes are drilled into the bottom of the holder for different diameter microphone
stand threads, choose the one that matches your mic stand.
POWER SWITCH:
The SGM-2X has a 3-position power switch.
OFF: Switch the microphone to OFF when not in use to conserve battery life.
ON: Switch the microphone to ON for normal operation.
: Switch to the LOW CUT position to reduce low frequencies and increase clarity.
MIC OUTPUT:
The SGM-2X has a balanced XLR output and will work in any low impedance microphone
input of 1K ohm or less. This includes balanced XLR or unbalanced ¼" and 3.5mm micro-
phone inputs. Due to the wide variety of possible connections and equipment used with the
SGM-2X, an output cable is not supplied.
WIRELESS OPTIONS:
You can turn the SGM-2X into a wireless microphone by purchasing one of Azden’s unique
XLR plug-in transmitters and matching receiver. For more details contact your Azden dealer or
one of the dealers linked at our website: www.azdencorp.com
SPECIFICATIONS:
FREQUENCY RESPONSE 40-20,000Hz
LOW-CUT ROLL-OFF 6dB/Octave @ 200Hz
SENSITIVITY SUPER CARDIOID -33dB re 1V/Pa
OMNI-DIRECTIONAL -39dB re 1V/Pa
IMPEDANCE 1.5k Ohms @ 1kHz
MAX. SPL INPUT LEVEL 110dB
SIGNAL TO NOISE RATIO 70dB
DYNAMIC RANGE 85dB
BATTERY TYPE AAA (1.5V) - USE ALKALINE BATTERY
BATTERY CURRENT 0.2 mA
BATTERY LIFE 1000 HOURS w/ALKALINE BATTERY
WEIGHT w/o BATTERY LONG + SHORT BARREL 6.5oz (185grams)
SHORT BARREL 3.9oz (110grams)
DIMENSIONS LONG + SHORT BARREL …….. 16" (400mm) length
…….. 0.83" (21mm) diameter
SHORT BARREL ………………. 8.4" (212.5mm) length
………………. 0.83" (21mm) diameter
OUTPUT TYPE 3-Pin XLR type
SUPPLIED ACCESSORIES SHOCK MOUNT MIC HOLDER
2 WINDSCREENS
Short Windscreen Long Windscreen
Long Barrel
Short Barrel
Shock Mount Holder
Capsule Cover