⑭
②
③
⑫
⑤
XLR input connector
Input level switch ⑨
AUX 1, 2 peak indicator
⑰
CH L XLR
output connector
⑱
CH R XLR
output connector
⑬
Phantom switch ⑧
Peak 2 indicator
①
Power switch
/ Power indicator
Input volume
PAN volume Master volume
⑥
Limiter switch
⑲
DC 12V jack
⑦
HPF switch ⑧
Peak 2 indicator ④
⑩
CH L, R VU meter
AUX 1, 2 volume
⑮
AUX 1, 2
input connector
⑯
EXT IN L, R
input connector
⑪
CH L, R output peak indicator
各部の名称とはたらき
●フロントコントロール部
●Rear Panel
Parts
●Front Control
①Power switch / Power indicator
Turns power ON/OFF / When power is ON, the red light will light up
②CH 1, 2, 3, 4, 5, 6 input volume
Adjusts the mix level volume of input signal from CH 1 - 6
③CH 1, 2, 3, 4, 5, 6 PAN volume
Control or stabilize the output balance of L ch and R ch of each input channel signal
④ AUX 1, 2 volume
Adjusts the RCA pin AUX input level of 2 systems
⑤MASTER volume
Adjusts the level of line out output (If set to the center, the output amp gain is ±0)
⑥CH 1, 2, 3, 4, 5, 6 LIMITER switch
Turns limiter function ON/OFF of CH 1 - 6 (When the function is ON, it suppresses the sound of
excessive input level without clipping)
⑦CH 1, 2, 3, 4, 5, 6 HPF switch
Turns Hi-pass filter function of CH 1 - 6 ON/OFF (If set to ON, it cuts the input signal under 100Hz)
⑧INPUT PEAK indicator
The indicator lights up in red when distorted by excess signal. This device has INPUT 1 & INPUT 2
indicators. When both indicators light up, it indicates below status;
PEAK 1 indicator :
Excessive signal is being inputted. Configuration of standard input or INPUT
LEVEL SW against the input source may be faulty.
Please try to change the configuration using INPUT LEVEL SW. If the light is
still lit up, the device is inputting signal excessively. Please adjust the output
level of connecting device.
PEAK 2 indicator : Mixing signal level is too high. Please adjust the signal level by ②Input volume.
⑨AUX INPUT PEAK indicator
The indicator lights up in red when distorted by excess signal. Adjust the signal level of mixing
signal by input volume.
Parts(Front Control)
⑩CH L, R VU meter
Analog VU meter which shows the line out output. Adjust the input signal level by input volume
or adjust the output signal level by MASTER volume; do not let it be off the scale, or let the output
peak indicator's light light up.
⑪CH L, R OUTPUT PEAK indicator
Monitors the line out output. Lights up in red when distorted by excessive output signal level.
When light up in red, adjust the input signal level by input volume or adjust the output signal level
by MASTER volume.
⑫INPUT LEVEL switch
3 types of input level can be chosen by connecting source to an input connector.
INPUT LEVEL (LINE) - Standard input level : +4dBu Maximum input level : +22dBu (16kΩ)
INPUT LEVEL (MIC HI) - Maximum input level : -6dBu (5kΩ)
INPUT LEVEL (MIC LO) - Maximum input level : -24dBu (4.6kΩ)
⑬PHANTOM switch
Turns the power of phantom power +48v ON/OFF. It can supply a MIC power +48v when ON. It can
only be used when MIC input is selected (INPUT LEVEL switch : MIC HI/ MIC LO).
Please turn OFF when no need of the phantom power. Before turning on the phantom power, please
confirm if the connecting device is compliant to phantom power. When turning the switch ON / OFF,
please adjust the volume to 0 all the time.
⑭CH 1, 2, 3, 4, 5, 6 XLR input connector
Suitable input sensitivity for the input source can be set by INPUT LEVEL switch
⑮AUX 1, 2 input connector
RCA pin AUX input which enables unbalance stereo signal input to 2 systems
⑯EXT IN connector / ON-OFF switch
EXT input ON/OFF switch mixes the XLR balance line L/R signal directly.
⑰CH L XLR output connector
Outputs the mixed L ch signal. Output level is +4dBu (LINE OUT).
⑱CH R XLR output connector
Outputs the mixed R ch signal. Output level is +4dBu (LINE OUT).
⑲DC 12V jack
Use the standard packed ac/dc adpter
(Rear Panel)
