AZZA OVERDRIVE User manual

OVERDRIVE

Physical Specifications
Model Name: OVERDRIVE
Name: CSAZ-807
Type:
Color:
Top Panel: Aluminum and tempered glass wing
Max CPU Cooler Height:
Max GPU Length: Up to 400mm long Video card (Horizontal)
Up to 80mm
Max Cooling Tube Reservoir Length: UP to 300mm
Power Supply: ATX
Motherboard Compability: <305x280mm E-ATX 、ATX、Micro ATX、Mini ITX
External 5.25" Drive Bays:
Internal 2.5" Drive Bays:
Internal 3.5" Drive Bays:
Expansion slots:
Front
Metal Chassis Dimensions (HxWxD)
Weight:
Outer Appearance:
440x570x590mm/17.3x22.4x23.2 inch
23kg /50.7lbs
Ports:
All external panels are made of aluminum with two glass top panel, gull-wing panel
design makes it easy to adjust and clean on usually.
Available Fan Ports:
Water Cooling:
Isolated Chamber:
Easy Installaon Cooler: A pre-cut hole for easy installaon of CPU Cooler,
eliminang the need to remove the motherboard
Accessories
Model
Specifications
ATX Tower
1.5~2.0mm SPCC+ 2.5mm Aluminum
Expansion
Up to 2
0
Up to 2 (Converble with 2.5"SSD x 2 )
3+3
3xUSB 3.0、HD Audio、Type C、Metal power buon
Features
Radiator bracket x 2 - Support 280/360mm on top two sides.
300 mm PCI-e 3.0 Riser Cable
AZZA Hub (RGB+Fan Controller) x1
PCI-e Slot Brackets x2
Decorave Backplates x2
Front: 1 x 200mm fan port (1x 200mm Addressable RGB fan included )
Top: 6 x 120mm/ 4 x 140mm fan ports
Sides: 6 x 120mm fan ports
Top: Supports radiators up to 280/360mm x 2
Sides: Supports radiators up to 360mm x 2
ATX Power supply inside its own isolated chamber,
prevenng its heat from affecng other components

1. Front Panel Functionality :
Front I/O:
Reset / LED / Audio / Mic / USB3.0*3 / Type C
200mm Addressable RGB Fan included
Front Fan:

2. Motherboard Installation :
)2()1( Turn the screws counterclockwise
to remove the glass.
Put the motherboard in from behind.
(3)Screw the motherboard onto the tray through the chassis.

3. Power Supply Installation :
Loosen the hand screws to remove the power supply
bracket. Attach the power supply to the bracket before
placing it back in.

4. Fan & Radiator Installation :
240 or 360 mm radiators
or 6*120 mm fans on the sides

5. Fan & Radiator installation :
•When installing a radiator:
Use long screws to affix the
fan and radiator onto the
chassis as shown.
•When installing fans only:
Use nuts on the rear of the screw to
affix the fan onto the chassis as
shown.

Install Reservoir and/or Pump
Turn the handscrews
counterclockwise to remove
6. Reservoir & Pump Installation :

Supports up to 280 mm or 360 mm radiator
7. Graphics Card or Radiator Installation :
Graphics Card length up to 400 mm / 3 slots
You can choose either side to install
Graphics Cards or additional radiators

8. Graphics Card Installation:
Attach the EVA foam supplied in the parts kit to support the
graphics card
PCI-e cable installation: Plug the cable onto the motherboard
by passing the cable through the hole as shown

Disk Drive Mounts on both sides:
9. Storage Drive Installation :
(1)Remove the 2 handscrews. (2)Lift and pull away to remove.
Disk Drive Mounts on both sides:
Two 2.5” drives or one 3.5” drive

Slide into cut-out
10. Rear Cover Installation :
Screw to secure

4 Pin PWM
SATA power connector
3 Pin Addressable RGB
2 pin connector to Reset(or LED) Switch
Ports and connectors
1.) 7x3 pin ARGB ports（supports ARGB devices: ARGB fan, ARGB strips…etc）
2.) 6x4 pin PWM fan ports
3.) 1x2 pin connector to Reset (or LED) switch
4.) 1xSATA power connector
5.) 1x3 pin ARGB connector to MB
6.) 1x4pin PWM fan connector to MB
Functions:
1.) Total of 17 lighting modes
2.) Lighting modes can be controlled by Reset (or LED) switch, or can be controlled by MB.
A.) Magnet on the back of the hub box or using velcro on the back of the hub box,
it can put in any place inside the metal part of the case.
B.) 6 sets of ARGB port next to PWM port to ease the connection on fans
(Hold the LED button for 3 seconds to switch the RGB control function between motherboard
RGB software and LED button)

C4
C1 C3
C2
J1
300 mm PCI-E 3.0 Cable(Support EATX、ATX Motherboard)