Baby Jogger city GO i-Size User manual

IMPORTANT! KEEP FOR FUTURE REFERENCE
Do not install or use this child restraint until you read and understand the
instructions in this manual.
FAILURE TO PROPERLY USE THIS CHILD RESTRAINT INCREASES THE RISK
OF SERIOUS INJURY OR DEATH IN A SUDDEN STOP OR CRASH.
car seat & base
babyjoer.com
city GOTM i-Size
Model City GO i-Size
0 - 87cm / ≤13kg
NWL0000669035A
©2017 BABY JOGGER 817
EN CS DE DA EL ES FI

2
1
2
15
11
4
5
6
3
8
9
12
7
13
14
11
5
7
10
EN
10
16
1 Carry Handle
2 Canopy
3 Body Support
4 Harness Covers
5 Buckle
6 Buckle Cover
7 Harness Straps
8 Harness Release Lever
9 Harness Adjustment Strap
10 Handle Adjustment Buttons
11 Lap Belt Path
(when used without the base)
12 Car Seat Release Handle
13 Headrest/Harness Adjustment Button
14 Shoulder Belt Path
(when used without the base)
15 Head Support
16 Headrest

3
2
3
6
7
1
4
5
EN
8
9 Harness Adjustment Strap
10 Handle Adjustment Buttons
11 Lap Belt Path
(when used without the base)
12 Car Seat Release Handle
13 Headrest/Harness Adjustment Button
14 Shoulder Belt Path
(when used without the base)
15 Head Support
16 Headrest
1 Car Seat Base Lock
2 ISOFIX Attachments
3 Car Seat Attachment
Indicator
4 ISOFIX Extend Buttons
5 ISOFIX Release Lever
6 Recline Handle
7 Support Le Adjustment
Buttons
8 ISOFIX uide caps

4
1 2
3
4
4

5
5
6 7
8
2
1
3
4
5
6
7

6
9
10 11
13 14
4
4
12

7
A
B
C
D
15
16 17
18 19
20 21
2.5 cm (1”)

8
23
25
26
24
22

9
27 28
29
31 32
30
33

10
34
35
36

11
WARNING
Do not make any alterations or additions to this child
restraint without the approval of the Type Approval
Authority, it is danerous to do so.
It is danerous not to follow closely the manufacturer
installation instructions provided with this child restraint,
FAILURE TO USE THIS CHILD RESTRAINT PROPERLY
INCREASES THE RISK OF SERIOUS INJURY OR DEATH
IN A SHARP TURN, SUDDEN STOP OR CRASH!
It is danerous to use the car seat on an elevated surface,
e.. a table.
Always use the restraint system.
This car seat is not intended for proloned periods of
sleepin.
Do not use as a reclined cradle once your child can sit
unaided.
This car seat does not replace a cot or a bed. Should your
child need to sleep, then it should be placed in a suitable
cot or bed.
Do not use the reclined cradle if any components are
broken or missin.
Do not use accessories or replacement parts other than
those approved by the manufacturer.
Important safety advice:
When this Infant Carrier is used in recline position 5, 6,
and 7, it may not fit in all vehicles approved for a Universal
fixture.
This child restraint is suitable for use by children within the
followin size rane 0 cm - 87 cm.
EN

12
This child restraint is suitable for use by children with a
maximum weiht of 13 k.
Please also check “i-Size Child Restraint System”
instructions in the vehicle manufacturer’s handbook.
It is very important to ensure that any lap strap is worn
low down, so that the pelvis is firmly enaed.
The riid items and plastic parts of a child restraint shall
be so located and installed that they are not liable, durin
everyday use of the vehicle, to become trapped by a
movable seat or in a door of the vehicle.
Do not use this child restraint in seatin positions where
there is an active frontal airba installed.
Any straps restrainin the child should not be twisted.
Any straps holdin the restraint to the vehicle should be
tiht.
The support-le should be in contact with the vehicle floor.
Any straps restrainin the child should be adjusted to the
child’s body.
This Child Restraint should be replaced when it has been
subject to violent stresses in an accident.
Do not leave a child in this child restraint unattended.
Any luae or other objects liable to cause injuries in the
event of a collision must be properly secured.
This Child Restraint System must not be used without the
cover.
The Child Restraint System cover must not be replaced
with any other than the one recommended by the
manufacturer, because the cover constitutes an interal
part of the restraint performance.
EN

13
! Even if usin this child restraint seems easy to fiure out
on your own, it is very important to READ, UNDERSTAND
AND FOLLOW THE OWNER’S MANUAL.
If you need help, please contact our Customer Service
Department with any questions you may have concernin
parts, use, or maintenance. When you contact us, please
have your product’s model number and manufactured in
(date) ready so that we may help you eciently.
The numbers can be found on a sticker on the back of
your child restraint.
! Your child’s safety depends on:
1. Choose proper head support position based on your
child’s size.
2. Properly securin your child in the child restraint.
3. Selectin a suitable location for the child restraint in
your vehicle.
4. Properly routin and securin the vehicle seat belt.
! THE CHILD RESTRAINT CAN BECOME VERY HOT IF
LEFT IN THE SUN. Contact with these parts can burn
your child’s skin. Always touch the surface of any metal or
plastic parts before puttin your child in the child restraint.
! NEVER USE A SECOND-HAND CHILD RESTRAINT or a
child restraint whose history you do not know.
EN

14
CAR SEAT INSTALLATION AND UNINSTALLATION
1 Rotate Support Le Out
2 Place base on vehicle seat. The support le has two
buttons to allow the lenth to be adjusted. Press the
buttons to adjust the le lenth. The support le must
contact the vehicle floor. Make sure the load le is
secure by pressin down on the base.
3 Extend the ISOFIX connectors.
Squeeze the ISOFIX extend buttons and pull the
ISOFIX connectors out.
4 Press the ISOFIX connectors onto the vehicle anchors
until a click is heard. When the ISOFIX connectors are
locked the connection indicators will be reen. If the
base is not locked in the indicators will be red.
5 Squeeze the ISOFIX extend buttons. Push down firmly
on the base towards the back of the vehicle seat to
ensure a tiht on the seat.
6 To release the base from the vehicle seat pull the
ISOFIX release lever and remove base.
RECLINE CAR SEAT
7 To recline the car seat pull recline handle and slide into
correct position for your child.
ATTACHING THE CAR SEAT TO THE BASE
8 To attach seat to base, position front of seat in base
then push down on the back until it locks into place.
Pull up on car seat to be sure it is securely fixed onto
base.
9 To remove, squeeze release handle at back of the
car seat to release the attachment catch. Lift car seat
from base as shown. Always place handle in the down
position when removin your baby from the seat and if
you place the car seat onto the floor.
EN

15
CAR SEAT INSTALLATION WITHOUT BASE
10 Place Car Seat Rear-Facin in the Vehicle
Place the car seat on the vehicle seat. Push it back
until the front of the car seat touches the vehicle seat
back.
11 Put lap section of belt over car seat and under the two
belt hooks marked in blue. Buckle the vehicle belt.
12 Place shoulder belt around the back of the car seat
exactly as shown, makin sure to run it throuh the
center uides on the back of the seat and below the
notch opposite the shoulder belt oriin. The seat belt
should lay as flat as possible and not be twisted. Make
sure buckle and seat belt are in line with each other.
Contact Baby Joer if in doubt about this point.
13 Tihten Vehicle Seat Belt
Lay your forearm across the car seat at the belt path
and push down. Pull on the shoulder belt to tihten
while feedin the slack back into the retractor.
ADJUSTING THE HANDLE
14 Squeeze latches on both sides at bottom of handle to
release it.
Rotate handle until it clicks into any of the 4 positions:
Position A (up): MUST be used when carryin by
handle,
Position B: Vehicle Travel Position
Position C: Convenience Position
Position D (down): is the sittin position.
Always place handle in the B position when usin it in
a vehicle.
SECURING CHILD
15 Loosen Harness Straps
Push down on the harness release lever while pullin
out on the harness straps.
EN

16
16 Press the red button on the buckle to unfasten the
buckle. Place harness straps o to the sides.
17 Place Your Child in the Seat
Make sure their back is flat aainst the car seat back.
18 Place Harness Straps Over Child’s Shoulders
19 Be Sure the Harness Straps are at the Proper Heiht
Harness straps must be at or just below the child’s
shoulders.
20 The top of child’s head must be at least 2.5 cm (1”)
below the top of the headrest.
21 To chane harness heiht, from the back of the seat,
squeeze the headrest adjustment buttons and move it
up or down to the correct harness position.
22 Buckle Harness Straps
Fit the two buckle tonues toether and push them
into the buckle. You will hear a “click” when buckle
tonues are securely attached. Pull up on the buckle
tonue to make sure it is securely attached.
23 Pull All the Slack Out From around the Waist
Pull up on the harness strap while pushin the buckle
tonue down. Do this on both sides.
24 Tihten the Harness by Pullin the Harness
Adjustment Strap
When you are not able to pinch any of the harness
webbin at your child’s shoulder, the harness is tiht
enouh.
UNSAFE VEHICLE SEAT LOCATIONS
Never install this car seat in any of the followin vehicle
seatin locations:
25 rear-facin or side-facin vehicle seats
26 rear-facin with an active front air ba
EN

17
27 Identify Your Seat Belt Type
There is only one type of vehicle seat belts that can
be used with this car seat: Combined Lap & Shoulder
Seat-belt 3 connections points.
ACCESSORIES
28 HEAD SUPPORT
Use only with infants up to 60 cm. To remove, slide
out from behind the headrest pad.
29 BODY SUPPORT
Use only with the lowest two sets of harness slots. To
remove, unbuckle the buckle and remove the body
support.
30 Harness Covers
To remove, undo the fastenin strips and remove.
CLEANING SEAT COVER
31 Unsnap the four buttons on the seat cover.
32 Pull out the 4 plastic flaps from the side of the seat.
33 Pull cover o the shell.
34 To remove canopy from the canopy hoop, first press
release tab and remove from mountin bracket, then
slide the canopy o the hoop to remove the canopy.
Machine wash cover and canopy in cold water on
delicate cycle and drip dry. DO NOT USE BLEACH.
Reverse the steps to reattach the cover to the shell.
Make sure the harness straps are not twisted.
CLEANING CROTCH BUCKLE
WARNING! Inspect and clean buckle from time to time
to remove any objects or debris that could prevent
latchin.
35 To clean buckle, place in a cup of warm water and
ently aitate the buckle. Press the red button several
times while in the water.
EN

18
DO NOT SUBMERGE THE BUCKLE STRAP. DO
NOT USE SOAPS, HOUSEHOLD DETERGENTS or
LUBRICANTS.
Shake out excess water and allow to air dry. Repeat
steps as needed until it fastens with a click.
CLEANING HARNESS
Surface wash only with mild soap and damp cloth. DO
NOT IMMERSE THE HARNESS STRAPS IN WATER
Doin so may weaken the straps.
If harness straps are frayed or heavily soiled, contact
Customer Service at babyjoer.com
36 Store instruction manual in the slot with the instruction
book icon as shown.
REPLACEMENT PARTS
To purchase parts or accessories, please contact us at
the followin:
babyjoer.com
EN

19
1
2
15
4
5
6
3
8
9
12
7
13
14
11
5
7
10
CS
11
10
16
1 Rukojeť
2 Klenba
3 Podpora těla
4 Kryty postroje
5 Přezka
6 Kryt přezkyw
7 Popruhy postroje
8 Odepínací páčka
postroje
9 Popruh nastavení postroje
10 Tlačítka uvolnění rukojeti
11 Vodítko klínového pásu při jízdě zády po
směru jízdy (při použití bez základny)
12 Páčka uvolnění autosedačky
13 Tlačítko pro úpravu hlavové opěrky/
postroje
14 Dráha ramenního pásu (při použití bez
základny)
15 Podpora hlavy
16 Opěrka hlavy

20
2
3
6
7
1
4
5
CS
8
1 Zámek základy dětské
autosedačky
2 Vodítka ISOFIX
3 Ukazatel upevnění dětské
autosedačky
4 Nastavovací tlačítka systému
ISOFIX
5 Odepínací páčka systému
ISOFIX
6 Sklápěcí rukojeť
7 Tlačítka nastavení opěrné
nohy
8 vodící krytky ISOFIX