Baby Jogger POD User manual

Read these instructions carefully
before use and keep them for
future reference. Your child’s
safety may be affected if you do
not follow these instructions.
www.babyjogger.com
POD
ASSEMBLY INSTRUCTIONS

2
• Avoid serious injury from falling or sliding out. Always use safety harness(es). Always
use the crotch strap(s) in combination with the waist belt(s).
• Do not install a car seat or any other seating device not approved by the manufacturer
inside this chassis.
• Make no modifications to this chassis.
• Do not allow any of the child’s body, clothing, shoe laces, or toys to come in contact
with moving parts.
• Never leave child unattended in the chassis.
• Not for use during inclement weather such as snow or ice.
• Use extra caution and slower speed when using on wet or uneven surfaces.
• Check passenger(s) frequently, during use in extreme hot or cold weather to avoid heat
exhaustion or hypothermia. Ensure the seating compartment is properly ventilated and
the child/children stay adequately hydrated.
• Recommended temperature limits are 32°F to 100°F (0°C-38°C).
• Do not use with children who exceed the weight limitations.
• Do not use cleaning solvents; clean only with mild soap and water.
• Do not use the POD on stairs. Resulting damage to the POD will not be covered
under warranty.
• This unit sits one or two passengers. When used with one passenger, the passenger
must be seated in the center position.
• Maximum weight capacity – 100lbs (45 kg) (combined passenger(s) and baggage weight.)
• Maximum baggage weight – 8lbs (3.6 kg)
• Children must be at least 12 months and able to sit upright unassisted to ride in chassis.
• Check tire pressure before each use. Your tires should be filled to a maximum of 50 psi.
For the sake of your precious cargo, please
read these warnings before using the POD.
WARNING:

1
1 Remove chassis from box and set
wheels aside.
2 Insert handlebar into handlebar attachment brackets until both
sides click into place.
3 To unfold the chassis: Lift handle up and away from the lower frame until it clicks into place.
4Turn chassis upright and attach red safety strap to snap located
just below the fold mechanism on right side of chassis.
Handlebar
Attachment Bracket
Safety
Strap Location
FRAME
Click

2
CANOPY
1 Lay chassis back so the handle is
resting on the ground. Locate the
white support rod at the top rear
of the POD seating compartment.
2 Insert support rod into black canopy brackets located
on each side of the frame.
3 Locate the white support rod
at the top center of the POD
seating compartment.
4 Insert support rod into black canopy brackets located
on each side of the frame.

3
1 To install rear wheels: Insert wheel axle into wheel
mount on chassis frame until it clicks into place.
NOTE: Ensure the wheel is properly secured
to frame, test by gently trying to pull the
wheel out after installing.
2 To remove rear wheels: Press the wheel release
button while sliding the wheel away from the
wheel mount.
Wheel Mount Release Button
2 Lift up on the brake pedal to
disengage the parking brake.
1 Push the brake pedal down to
engage the parking brake.
Warning: Engage parking brake before loading and unloading passenger(s).
Engaged Disengaged
REAR WHEELS
& PARKING BRAKE

4
For use with a single passenger:
Warning:
When used with
only one child, the
child must be seated
in the center seating
position.
3 Buckle center waist belt.2 Place child in center seating
position. Buckle harness yoke
to center crotch strap buckle.
1 Buckle shoulder straps of harness yoke into center two buckles
on back of seat.
SAFETY HARNESS
ATTACHMENT & CONFIGURATION

5
For use with two passengers:
3 Buckle the waist belt.2 Place child in right seating
position. Buckle harness yoke
to the crotch strap buckle. (The
center crotch buckle will not
have a harness yoke attached.)
1 Buckle shoulder straps of harness yoke into two right buckles
on back of seat.
4 Repeat steps 2 and 3 to
secure second child into
safety harness on the left
side of the seat.

6
2 Rethread webbing strap
through front of harness
yoke to hold in place.
1 Thread webbing strap through
plastic guide on upper buckle
to lengthen or shorten.
To adjust crotch strap:
1 Thread webbing strap through
plastic guide on lower buckle
to lengthen or shorten.
To adjust waist belt:
1 Thread webbing strap through
waist buckle to lengthen or
shorten.
SAFETY HARNESS
SAFETY HARNESS ADJUSTMENT
To adjust shoulder harness length:

7
To adjust shoulder harness height:
2 Unclip harness yoke from
seat back.
1 Pull mesh seat back down to
expose upper harness buckles.
3 Slide the buckle down
to desired height.
5 Fasten harness buckle to seat
back and repeat on other side.
4 Thread harness yoke through
lower opening on mesh seat back.

8
The handlebar on the POD has two height adjustments.
2 Flip the handlebar over and reinsert into handlebar attachment brackets until both sides click into place.
1 Press buttons on each side of the handlebar attachment brackets while
pulling the handle tubing out.
To adjust the height of the handlebar:
Handlebar
Attachment
Bracket
Highest
Position
Lowest Position
ADJUSTABLE HANDLEBAR
Click