Baby Jogger ATS User manual

Read these
instructions carefully
before use and
keep them for
future reference.
Your child’s safety may be
affected if you do not follow
these instructions.
Assembly
Instructions
ATS All Terrain Swivel
• 360° Swivel Front Wheel For Extreme Maneuverability
• Air Glide Suspension System For Smooth
And Comfortable Ride
This product complies with ASTM F833-05a

B
• WARNING: Prevent serious injury to your child by always using the
safety harness.
• WARNING: Any load attached to the handle affects the stability of the stroller.
• WARNING: It may be dangerous to leave your child unattended.
• WARNING: Recommended weight for seat pocket is 2 lbs. (1 kg.)
and basket is 10 lbs. (4.5 kg.). Excessive weight may cause a hazardous
unstable condition to exist.
• Unapproved accessories shall not be used.
• Always use your wrist strap – these strollers can really roll, and the
wrist strap gives you control if you should slip or fall down.
• The passenger should remain seated (no standing in the stroller).
• Watch out for cars – never assume that a driver can see you and your child.
• Intended for passengers up to five years of age.
• Total weight load recommended for this stroller is 75 lbs. (34 kg.)
(combined passenger and baggage weight.)
• This stroller seats one passenger.
• It may be unsafe to use replacement parts other than those supplied or
approved by the manufacturer.
• Never use roller blades while using a Baby Jogger.
For the sake of your precious cargo, please read
these warnings before using your stroller.

Frame
1
1. Unpack stroller from box and set wheels aside.
2. Flip stroller so handle is laying on top and pull handle up until frame locks into position.
WARNING: Ensure all
locking devices are
engaged before use.
2a
2b 2c
2d

2
Footplate
NOTE: The footplate will come with two screws. If you are missing one, please give us a
call at 800.241.1848.
1. Lay footplate onto stroller frame.
You may need to remove lower
section of the seat to gain better
access.
2. While holding onto footplate, push up
on stroller frame until handle is laying on
floor. This will allow you to look under
footplate in order to secure it to frame.
3. Align the holes on the frame with the holes
on the footplate and secure with the screws.

3
Front Wheel
1. To install front wheel, keep stroller with
handle resting on the floor and lock front
wheel forks by pushing down on locking
button on footplate.
2. Insert the front wheel into forktips by
aligning the axle flats with the forktips flats
and inserting the skewer latch into the
stroller’s front forks.
3. Secure front wheel to frame by turning the front wheel
lever while holding the lock nut on the opposite side.
Tighten until you feel tension on the lever and then
flip wheel lever over so that the word “CLOSED” is
visible. The wheel lever should face toward the rear
of stroller to prevent it from
getting accidentally caught on
something and opening up
during use.
Bring stroller frame back into
the upright position.
Skewer Latch
Front Fork

4
• To install rear wheels, push on
the button located at center
of wheel and gently slide the
wheel‘s axle into the hole in
the stroller‘s axle end until
you hear it click into place.
• To remove, simply push in on
the button located at center
of wheel while pulling out
the wheel.
Rear Wheels
IMPORTANT: To ensure the wheel is properly secured to the frame, test by trying to
pull the wheel out after installing.

5
1. Fasten front end of basket by securing
the basket snap straps around the frame
right above the footplate.
Basket
2. Now secure the back end of the basket
around the center bar on the stroller frame.

6
Seat
• Fasten the two bottom
Velcro straps to their
partner straps by threading
each Velcro strap through
the D-Ring and Velcro
back to themselves.
Your seat comes partially attached to the frame.
Please follow the steps below to finish securing it.

7
1. To recline: Pinch the clam and slide it down
the recline strap to desired angle and gently
push seat down with your hand.
2. To return to the upright position:
Hold the D-Ring on the end of the recline
strap in one hand and use the other to
pinch the clamp and slide it up the strap.
Reclining Seat
1. To secure
the beverage
holder onto
your stroller,
simply Velcro
straps around
handlebar frame
and Velcro back
to itself.
Beverage Holder
Store small items such as cell phone, keys and small wallets
in the zipper compartment so that they are not lost.
When installed the beverage
holder will look like this.

8
4. To adjust side straps: Press side buckle latch
and slide strap to lengthen or shorten.
Safety Harness
WARNING: Always use the crotch strap in combination with
the waist belt.
1. Unclip top of shoulder
strap from the seat and
re-clip on the pair of seat
loops closest to child‘s
shoulder height.
3. To buckle: Simply push side
buckle into center buckle until
it locks in place.
To unbuckle: Press one side
of the center button and pull
the corresponding side buckle
away from the center buckle.
2. To adjust the strap length:
Remove the shoulder pads
and move the plastic guide
up or down to lengthen or
shorten.
5. To adjust
the center
strap,
move its
plastic
guide up
or down.