Baby Jogger Q-SERIES TRIPLE User manual

Important, Keep for
Future Reference
Assembly
Instructions
Amazing Quick Folding System (Patented)
Q-Triple
Q-Triple (Assem) 4/6/05 2:09 PM Page 1

2
• Important, keep this booklet for future reference.
• Accessories which are not approved by the manufacturer or distributor
should not be used.
• WARNING: Prevent serious injury to your child by always using the
safety harness.
• WARNING: Any load attached to the handle affects the stability of the Jogger.
• WARNING: Do not leave child unattended.
• Always use your wrist strap – Your Jogger can really roll, and the
wrist strap gives you control if you should slip or fall down.
• The passengers should remain seated at all times (no standing in the Jogger).
• Watch out for cars – never assume that a driver can see you and your child.
• Never use Roller Blades while using your Baby Jogger.
• Total weight load recommended for this Jogger is 125 lbs.
(combined passenger and baggage weight).
• This Jogger seats three passengers.
• WARNING: Recommended weight for seat pocket is 2 pounds and basket
is 10 pounds. Excessive weight may cause a hazardous unstable
condition to exist.
• It may be unsafe to use replacement parts other than those supplied or
approved by the manufacturer.
For the sake of your precious cargo, please read
these warnings before using your Baby Jogger.
Q-Triple (Assem) 4/6/05 2:09 PM Page 2

1
Frame
• To assemble, simply unfold frame as shown.
12
34
Q-Triple (Assem) 4/6/05 2:09 PM Page 1

2
1 To install front wheels,
lay Jogger back so handle
is resting on floor. Open
the caliper by flipping
the caliper lever toward
the rear wheels.
2 Insert one of the front
wheels into the fork tips
by aligning the axle flats
with the fork tip flats.
3 Tighten by turning the
wheel lever while holding
the opposite side.
4 Close the wheel lever
making sure that it is
facing toward the back
of the Jogger.
5 Close caliper by flipping
the caliper lever toward
the fork tips.
Repeat these steps to
install other wheel.
Front Wheels
Caliper Lever
Wheel
Lever
Q-Triple (Assem) 4/6/05 2:09 PM Page 2

3
• To install, gently slide the
wheel’s rear axle into the hole
in the axle end until you hear it
click into place.
• To remove, simply push in
the spring lock while pulling
out the wheel.
Rear Wheels
Q-Triple (Assem) 4/6/05 2:09 PM Page 3

4
• If you don’t have good braking
action, simply squeeze the brake
handle five or six times. If the
problem persists, loosen the
brake’s cylinder ring to adjust the
small ring, and then move the
small ring away from the handle
to tighten the cable. (Please do
not over tighten!) To lock the
rings, tighten the cylinder ring
against the handle while holding
the small ring in place.
Hand Brake with
Parking Button
• To use the parking button feature, simply squeeze
the brake handle and push the park brake button.
Rear Wheel Parking Brake
• Simply push brake pedal down to engage brake
and lift up to release.
Brakes
Small Ring
Parking
Button
Cylinder
Ring
JOGGER IS PACKAGED
WITH THE HAND BRAKE
ASSEMBLY LOOSE.
TIGHTENING IS NECESSARY
FOR SAFE OPERATION!
• Rotate hand brake assembly upward to a comfortable
position then tighten bolt (clockwise) on the hand
brake assembly with supplied allen wrench as shown.
Adjusting the Brake
Q-Triple (Assem) 4/6/05 2:10 PM Page 4

5
Adjusting
safety harness:
1 Loosen the shoulder straps from their
plastic guides.
2 Slide the end of each strap through pair of
seat loops closest to your child’s shoulder.
3 Slide the end of the shoulder strap back
into plastic guide.Please note: If you feel
the straps are too tight, you may adjust
their length by sliding the plastic guides
toward the top of the seat.
4 Lock both sides of the strap mechanism
into the center buckle. To adjust the center
strap, move its plastic guide up or down.
Safety Harness
WARNING: Avoid serious injury from falling or sliding out.
Always use safety harness!
Q-Triple (Assem) 4/6/05 2:10 PM Page 5

6
1Simply adjust seat
straps to desired
degree of recline.
2Pull on strap when you
want to return the seat
to its upright position.
3Rear flap serves as sun
canopy when seat is in
reclined position.
Reclining Seat
4Jogger is packaged with seat support board and can be easily removed
or inserted into the seat back if additional support is desired.
Be sure to remove the board from the back of the seat before washing.
Q-Triple (Assem) 4/6/05 2:10 PM Page 6

Folding
Simple
Lift & Fold
Yellow
Safety
Straps
Must Be
Released
Before
Folding
7
1Retract sun canopies and unsnap the yellow safety straps from Jogger frame.
2Stand in front of the Jogger with your body centered over one front wheel. Grasp
both fold straps and firmly pull upwards to fold.
ALWAYS BE SURE
THE YELLOW
SAFETY STRAP
IS SECURELY
SNAPPED ONTO
THE FRAME
BEFORE USING
JOGGER!
Q-Triple (Assem) 4/6/05 2:10 PM Page 7

8
Seat
1 Snap seat to frame. 2 Attach bottom part of seat
to footplate with the Velcro.
3 Wrap bottom straps around
frame, thread each strap
through D-ring and secure.
5 Snap all center yellow
safety straps to Jogger
frame.
6 Snap safety strap to
side frame.
4 Standing behind stroller,
locate the center seat straps,
and snap them to each
other connecting all seats.
NOTE: Some Joggers are shipped
with the Canopy, Seat and Basket
pre-assembled. Assembly instructions
are given if any pre-assemble items are
removed for cleaning or replacement.
Q-Triple (Assem) 4/6/05 2:10 PM Page 8