BaByliss MULTI STYLE 2800DU User manual

MULTI STYLE
2800DU
SAFETY CAUTIONS
• This appliance should only be used as described within
this instruction booklet. Please retain for reference.
IMPORTANT CHILD SAFETY
WARNING! Polythene bags over a product or package
may be dangerous. To avoid danger of suffocation, keep
this wrapper away from babies and children. This bag is
not a toy.
WARNING! THIS APPLIANCE GETS HOT!
• ALWAYS keep out of reach of children (during and after
use and whilst cooling).
• This appliance should not be used, cleaned or
maintained by children.
• Always take extra care if used on children or near
children.
• Do not use on very young children.

IMPORTANT SAFETY
• Do not use the appliance in the bathroom.
• WARNING! Do not use this appliance near water
contained in basins, bathtubs or other vessels.
• Do not immerse the appliance in water or other liquids.
• Always inspect the appliance before use for noticeable
signs of damage. Do not use if damaged, or if the
appliance has been dropped. In the event of damage,
discontinue use immediately. Contact the Conair
Customer Care Line (refer to ‘UK After Sales Service’
section for further information).
• Do not use the appliance if the lead is damaged. In the
event of lead damage, discontinue use immediately.
If the lead is damaged it must be replaced by the
manufacturer. Return the appliance to the Customer
Care Centre (refer to ‘UK After Sales Service’ section
for further information). No repair must be attempted
by the consumer.
• Do not leave the appliance unattended when switched
on or plugged in.
• During use, do not place the appliance on any heat
sensitive surface.
• Take care to avoid the hot surface of the appliance
coming into direct contact with the skin, in particular
the eyes, ears, face and neck.
• This appliance should not be used by adults whose
reduced physical, sensory or mental capabilities, or
whose lack of experience and knowledge, might cause
a hazard, unless they have been correctly instructed to

understand the safe use and hazards involved and are
adequately supervised.
• Allow appliance to cool before storing away.
• After use, do not coil the lead around the appliance as
this may cause damage. Instead, coil loosely by the
side of the appliance.
• This product complies fully with all appropriate EU
and UK Legislation and the Standards relevant to this
type and class of appliance. We are an ISO9001:2015
certied company that continually evaluates our
Quality Management System performance. If you have
any queries regarding product safety and compliance,
please contact our Customer Services Department.
(See “U.K. After Sales Service” section for further
information.)

INSTRUCTIONS FOR USE
• Ensure the hair is dry and combed through to remove any tangles.
Divide the hair into sections ready for styling.
• Fit the required attachment as described below, ensuring that the
attachment is locked into position.
• To remove the attachments ensure the appliance is cool and
unplugged. On the power handle there are two slide switches on the
top and lower housing. Slide back the switches individually and pull
to release the separate attachments.
• Follow the instructions for each attachment as stated below.
• Plug the appliance into a suitable mains socket and slide the switch
to the ‘I’ to turn on, the ‘on’ indicator light will illuminate.
• Always place on a rm surface using the safety stand on the base
of the appliance. Do not place the appliance on any heat sensitive
surface.
• Allow the appliance to heat up.
• After use slide the switch to ‘0’ to turn off and unplug the appliance.
• Allow to cool before storing away
IMPORTANT! The element of the appliance will become very hot when
plugged in and switched on. Before xing or removing any attachments,
ensure the appliance is cool, switched off and is unplugged.
13MM/16MM/19MM TONG ATTACHMENTS
To create, tight or loose curls:
- Use the 13mm tong to create tighter curls
- Use the 16mm tong to create dened curls
- Use the 19mm tong to create loose curls
Fitting The Tong Attachments
• Insert the correct size tong in the bottom slot of the power handle.
On the bottom of the attachment there is a small ridge, ensure this
is facing downwards and then push the attachment into the handle
until it clicks into place.
• Hold the handle in the closed position and insert the spring lever in
the top slot of the appliance. On the top of the spring lever attachment

there is a small ridge, ensure this is facing upwards and then begin
to push the attachment into the handle, whilst still holding the handle
in the closed position you will need to line up the grooves on the
attachment so that they connect with the tong attachment and it clicks
into place.
NOTE: When using the 19mm tong only insert it as one attachment, as
the spring lever is already attached to the tong.
Instructions Of Use - 13mm, 16mm And 19mm Tong Attachments
• Ensure the hair is dry and combed through to remove any tangles.
Divide the hair into sections ready for styling and allow the appliance
to heat up.
• Pressing the lever, place the appliance midway up a section of hair
and spread hair evenly between the lever and barrel.
• Once hair is in place carefully let go of the lever so the hair is held
securely between lever and barrel. Gently slide the appliance down
to the hair ends.
• Wind the hair around the barrel at a slight angle, so the hair wraps
around the barrel in a spiral motion. As you wind the hair around the
barrel, ensure the hair is distributed evenly so the entire section is
touching the barrel, try not to overlay the hair.
• Hold in place for 5-10 seconds depending on the texture and length
of your hair.
• To remove the appliance from the hair, press the lever and pull
appliance away.
• Allow the curl to cool before styling.
• Repeat on each hair section.
• After use, switch off and unplug the appliance.
• Allow to cool before storing away

DUAL BARREL TONG ATTACHMENT
To create waves and styles with movement:
- Use both the 13mm and 16mm tongs
Fitting The Dual Barrel Tong Attachment
• Insert the 13mm size tong in the bottom slot of the appliance. On the
bottom of the attachment there is a small ridge, ensure this is facing
downwards and then push the attachment into the handle until it
clicks into place.
• Hold the handle in the closed position and insert the 16mm size tong
in the top slot of the appliance. On the top of the 16mm size tong
attachment there is a small ridge, ensure this is facing upwards and
then begin to push the attachment into the handle, whilst still holding
the handle in the closed position you will need to line up the grooves
on the attachments so that they connect with each other and click
into place.
Instructions For Use - Dual Barrel Tong
• Ensure the hair is dry and combed through to remove any tangles.
Divide the hair into sections ready for styling and allow the appliance
to heat up.
• Take a small section of hair and wind the hair around both barrels.
Take care to avoid the hot surface of the barrels.
• Hold in place for 5-10 seconds, depending on the length and texture
of the hair.
• Release the end of the hair and slowly pull the tong from the hair.
Allow the curl to cool before styling.
• Repeat on each hair section.
• After use, switch off and unplug the appliance.
• Allow to cool before storing away

SPIRAL SLEEVE ATTACHMENT
To create ringlets and tousled curls:
- Use the 19mm tong with the spiral sleeve
NOTE: The spiral sleeve can only be used with the 19mm tong
attachment.
Fitting The Spiral Sleeve Attachment
• Ensure the 19mm tong is inserted into the appliance (Please see the
‘Fitting The Tong Attachments’ section for direction) and is completely
cool. Push the spiral sleeve over the tong and the long lever. Once
the sleeve has reached the small lever press the spoon button and
continue to push the sleeve to the end of the barrel to attach.
Instructions For Use - Spiral Sleeve
• Ensure the hair is dry and combed through to remove any tangles.
Divide the hair into sections ready for styling and allow the appliance
to heat up.
• Pressing the lever, place the end of the hair section under the small
lever. Once hair is in place carefully let go of the lever so the hair
is held securely between lever and barrel. To avoid crimped ends,
ensure the ends are securely wound under the lever in the direction
of the desired curl.
• Twist the appliance upwards, winding the hair around the tong,
keeping the hair within the spiral guides. Wind the hair upwards,
taking care to avoid the hot surface of the barrel touching the scalp.
• Hold in place for 5-10 seconds depending on the texture and length
of your hair.
• To remove the appliance from the hair twist the appliance downwards,
unwinding the hair from around the barrel and press the lever and pull
appliance away.
• Allow the curl to cool before styling.
• Repeat on each hair section.
• After use, switch off and unplug the appliance.
• Allow to cool before storing away

BRUSH SLEEVE ATTACHMENT
To create shape, texture and volume:
- Use the 19mm tong with brush sleeve.
NOTE: The brush sleeve can only be used with the 19mm tong
attachment.
Fitting The Brush Sleeve Attachment
• Ensure the 19mm tong is inserted into the appliance (Please see the
‘Fitting The Tong Attachments’ section for direction) and is completely
cool. Push the brush sleeve over the tong and the long lever until it
reaches the end of the barrel to attach.
Instructions For Use - Brush Sleeve
• Ensure the hair is dry and combed through to remove any tangles.
Divide the hair into sections ready for styling and allow the appliance
to heat up.
• Place the brush at the roots and slide downwards towards the ends
of the hair.
• To add shape, roll a section of hair around the brush and hold for
5-10 seconds. On longer styles, be careful not to overlay the hair
around the barrel as this may cause tangling.
• Allow the section of hair to cool before styling.
• Repeat on each hair section.
• After use, switch off and unplug the appliance.
• Allow to cool before storing away
STRAIGHTENER/CRIMPER ATTACHMENT
To create sleek or crimped styles:
- Use the straightener/crimped plates
NOTE: This appliance has one set of heated styling plates, which are
reversible for crimping or straightening. Once the plate attachments are
tted it is simple and easy to change between using the straightening
plates and crimping plates without having to remove the attachments
themselves.

Fitting The Straightener/Crimper Attachment
Insert both styling plate attachments into the two slots in the power
handle, to do this make sure the ridge is lined up so the attachments
can be clicked into place.
Changing The Plates
To change between the plates, close the power handle together and
simply push down the convertible button that is on the side of the
styling plate attachment.
Instruction For Use - Straightener Plates
• Ensure the hair is dry and combed through to remove any tangles.
Divide the hair into sections ready for styling and allow the appliance
to heat up.
• Place the section of hair between the plates, close to the roots.
• Hold the hair rmly between the plates and slide slowly down the
length of the hair, from root to tip.
• Allow the hair to cool before combing through.
• Repeat on each hair section.
• After use, switch off and unplug the appliance.
• Allow to cool before storing away
Instruction For Use - Crimping Plates
• Ensure the hair is dry and combed through to remove any tangles.
Divide the hair into sections ready for styling and allow the appliance
to heat up.
• Clamp a section of hair between the top and bottom plates by
pressing the styler together. Hold in place for 5-10 seconds.
• Release the appliance from the hair and re-position the plates so
that the next crimp falls in line with the rst or do random sections
depending on your style.
• Always work from the roots towards the end of the hair.
• Repeat on each hair section.
• After use, switch off and unplug the appliance.
• Allow to cool before storing away

CARE & MAINTENANCE
To help keep your appliance in the best possible condition follow the
steps below:
• Do not wrap the lead around the appliance, instead coil the lead
loosely by the side of the appliance.
• Do not use the appliance at a stretch from the power point.
• Always unplug after use.
For more information on this appliance visit www.babyliss.co.uk
UK GUARANTEE
The Conair Group Ltd, Unit 3, Waterfront Business Park, Fleet,
GU51 3TW
This BaByliss appliance is guaranteed for consumer use for 3 years
and is only valid within the United Kingdom.
This guarantee covers consumer use only i.e. defects occurring under
normal use within the home from date of purchase or date of delivery,
whichever is later.
If the product develops a fault due to defects in materials or manufacture
within 12 months from the date of purchase, to avoid delays and
unnecessary inconvenience, where possible please return the product
to the point of purchase for an exchange.
If the product develops a fault due to defects in materials or manufacture
after 12 months from the date of purchase, and within the guarantee
period, Conair UK After Sales Service will repair or replace the product.

Exclusions
This guarantee will no longer be valid meaning that The Conair Group
Ltd will not be liable to repair or replace your product where:
1.) The appliance has been used on a voltage supply other than that
which is marked on the product, or advised within this instruction
booklet
2.) The appliance has been purchased from an unauthorised stockist*
3.) The appliance is used for professional / non domestic usage
4.) Repairs or alterations have been attempted by unauthorised persons
5.) The failure of the appliance is a direct result of misuse
6.) The failure is a result of not following the instructions for use
This guarantee does not cover any cosmetic damage due to misuse
of the product nor any damage to persons or property that occurs
because of product misuse.
*unauthorised stockists include, but are not limited to online auction
sites, private sellers and those selling second hand goods, refurbished
products etc
Please contact the Conair Customer Care Line on 03705 133 191
(09:00 to 17:00 Monday to Friday) or e-mail [e-mail] for
further information on authorised stockists.
It is important to retain your proof of purchase. We recommend
attaching your receipt to this page.
Even where a refund may be applicable, no refund will be provided
without a valid receipt or proof of purchase, we will only be able
to offer a repair or replacement service. Please note this does
not apply if the product was purchased directly from The Conair
Group Ltd.

Guarantees on replacement products run from the original purchase
date or date of delivery, whichever is later, and not from the date of
replacement.
This guarantee is an additional benefit and does not affect your
statutory rights as a consumer.
If you have any queries regarding this guarantee please contact the
Conair Customer Care Line on 03705 133 191 (09:00 to 17:00 Monday
to Friday) or e-mail [e-mail]
UK AFTER SALES SERVICE
For further advice on using the appliance or should you need to return
your product, please contact the Conair Customer Care Line on
03705 133 191 (09:00 to 17:00 Monday to Friday) or e-mail your enquiry to
[e-mail]
Return address:
Customer Care Centre
Conair Logistics
Unit 4, Revolution Park
Buckshaw Avenue
Buckshaw Village
Chorley
PR7 7DW
Please enclose your returns number, name and address details,
together with a copy of proof of purchase and details of the fault.
Please note this Instruction Booklet is not the guarantee.

SAFE DISPOSAL
The symbol on the product or on its packaging indicates that this
product may not be treated as household waste. Instead it should be
handed to an appropriate collection point for the recycling of Electrical
and Electronic equipment. By ensuring this product is disposed of
correctly, you will help prevent potential negative consequences for
the environment and human health, which could otherwise be caused
by inappropriate waste handling of this product. For more detailed
information about the recycling of this product, please contact your
local council ofce or your household waste disposal service.