Badger Basket 02240 User manual

2.0/1008/TG
MODEL NUMBERS:
02240 - White
02241 - Natural
02242 - Cherry
Page 1 of 6
SLEIGH STYLE BABY
CHANGING TABLE WITH
DRAWER
Assembly
Instructions.
AdultAssembly
Required.
Save these
instructions for
future use.
Visit us online at www.badgerbasket.com
Toll-Free Customer Service: 1-800-236-1310 (Monday through Thursday 7:30AM to 4:30 PM CST)
Web: http://www.badgerbasket.com/parts • E-mail: p[email protected]
Mail: PO Box 227, Edgar, WI 54426-0227 • Phone: [phone] • Fax: [phone]

2.0/1008/TG
BEFORE YOU BEGIN ASSEMBLY:
Check all parts and hardware. If anything is missing or not
satisfactory, please DO NOT call the store where purchased or
return the product to them. Contact Badger Basket for assistance.
Most problems are resolved without you needing to leave home.
When contacting us, please have this instruction manual, your
product model number, and your product version code ready.
For fastest service, go to
http://www.badgerbasket.com/parts
Your Product Version Code is: 2.0/1008/TG
USE AND CARE INSTRUCTIONS:
Wipe the table, pad, and safety belt clean with a damp cloth and mild soap as needed.
READ ALL INSTRUCTIONS before use of this changing table. Keep instructions for future use.
Choking Hazard! Keep unassembled parts out of the reach of small children. Use only the parts,
hardware, and changing pad provided by Badger Basket. Do not use the changing table if it is
damaged or broken.
FALL HAZARD - To prevent death or serious injury, always keep baby within arm’s reach.
NEVER leave your baby unattended, not even for a moment, when you are changing Baby’s
diaper.
ALWAYS use the safety belt provided; and as an extra precaution keep at least one hand on
your baby at all times. DO NOT allow any children to climb or play on the table. Periodically
check to make sure all the bolts and screws remain tight and that the drawer is properly aligned
in its tracks. NEVER load the drawer with items weighing more than a total of five (5) pounds (2.3
kg). NEVER lean on the drawer when it’s open and never use the drawer as a surface for
changing your baby.
This table is suitable for use with children weighing up to 30 lbs. (13.64 kg).
WARNING - FAILURE TO FOLLOW THESE WARNINGS
AND THE INSTRUCTIONS COULD RESULT IN
SERIOUS INJURY OR DEATH
Page 2 of 6

2.0/1008/TG
TABLE PARTS INCLUDED:
(A1) 1 - Right Outside Drawer Track
(A2) 1 - Left Outside Drawer Track
(B1) 1 - Right End Panel
(B2) 1 - Left End Panel
(C) 6 - ½” Screws
(D) 16 - Black Pegs
(E) 2 - Top Rails
(F1) 2 - Top Shelf Rails**
(F2) 4 - Middle/Lower Shelf Rails
(G) 16 - 1¾” Bolts
(H1) 1 - Top Shelf Panel**
(not shown)
(H2) 2 - Middle/Lower Shelf Panels
(not shown)
(I) 1 - Safety Belt
(J) 1 - Metal Support Bar
(K) 2 - 5/8” Screws
(L) 1 - Mattress Pad (not shown)
DRAWER PARTS INCLUDED:
(M) 4 - Metal Pins
(N) 1 - Left Side Panel
(O) 1 - Right Side Panel
(P) 1 - Back Panel
(Q) 4 - Round Metal Cams
(R) 1 - Bottom Panel
(S) 1 - Front Panel
(T1) 1 - Left Inside Drawer Track
(T2) 1 - Right Inside Drawer Track
(C) 6 - ½” Screws
Page 3 of 6
Px1
Sx1
Rx1
Nx1
Ox1
B1x1
F1x2
F2x4
B2x1
Ix1 Jx1
Ex2
A1x1
Dx16
Cx6
T1x1
Gx16
Kx2
A2x1
T2x1
Mx4 Qx4
PARTSAND HARDWARE:
TOOLS NEEDED (not included):
Phillips Screwdriver
StandardScrewdriver
Power driver is helpful but be careful not to damage the product.
ASSEMBLY NOTES:
Parts & Hardware diagrams not to scale.
* Style of PEGS may vary from shown
** The two TOP SHELF RAILS have a larger shelf groove
than the other four rails. The TOP SHELF PANEL is thicker
than the middle/lower shelf panels.

2.0/1008/TGPage 4 of 6
STEP1 - PICTURE 1: Attach the TWO OUTSIDE DRAWER TRACKS (A1 andA2) to the TWO END PANELS (B1, B2)
using SIX ½” SCREWS (C) (three screws for each track). Line up the first hole behind the track wheel so that all three screw
holes on (B) match up to holes on (A), and the narrower end of (A) lines up with the end of the track board.
STEP 2 - PICTURE 2: Insert the SIXTEEN BLACK PEGS (D) into the peg holes on the ends of the TWO TOP
RAILS (E) and the SIX SHELF RAILS (F1, F2). Push the thinner end of the peg into the hole until the wider end is
flush with the wood.
STEP 3 - PICTURE 3: Attach ONE TOP RAIL (E), ONE TOP SHELF RAIL (F1), and TWO MIDDLE/LOWER
SHELF RAILS (F2) to ONE END PANEL (B2 is shown, but you can begin with B1 if desired) using FOUR 1¾”
BOLTS (G). The grooves on the SHELF RAILS (F1, F2) face in and line up with the shelf grooves on the END PANEL
(B2).
STEP 4: See PICTURE 4. Repeat Step 3 to attach the remaining TOP RAIL (E), TOP SHELF RAIL (F1), and TWO
MIDDLE/LOWER SHELF RAILS (F2) to the END PANEL (B2).
PICTURE 1
Track Board
B1
A1
Narrow End
EF1,
F2
DD
PICTURE 2
E
B2
F1 F2
F2
PICTURE 3 PICTURE 4
E
STEP 5 - PICTURE 5: Rest the table on the END PANEL (B2). Insert the TOP SHELF PANEL (H1) and MIDDLE/
LOWER SHELF PANELS (H2) into the grooves on the SIX SHELF RAILS (F1, F2) with the white or colored sides
(depending on your model) of the shelves facing up. Be sure the shelves are seated into the grooves on all three sides.
B2
F1
F2
F2
*You must be sure to
use the F1 rails with
thethickergrooves
in the top positions.

2.0/1008/TGPage 5 of 6
PICTURE 8
H1
PICTURE 5
B2
H2
B1
PICTURE 6
STEP 6 - PICTURE 6: Attach the SECOND END PANEL (B1) to the TWO TOP RAILS (E) and SIX SHELF RAILS
(F1, F2) using EIGHT 1¾” BOLTS (G).
STEP 7 - PICTURES 7A, 7B and 7C:
Note: This step can also be completed with the table upside down to make it easier.
See PICTURE 7A. Slip one end of the SAFETY BELT (I) between the TOP RAIL (E) and the TOP SHELF
RAIL (F1).
See PICTURE 7B. Using the pre-made hole on the SAFETYBELT (I) and the pre-drilled hole on the underside of
the TOPSHELF RAIL (F1), sandwich the end of the SAFETYBELT (I) between the METAL SUPPORT BAR (J) and the
top shelf rail as shown and secure with ONE 5/8” SCREW (K).
See PICTURE 7C. Secure the other end of the SAFETY BELT (I) and the other end of the METAL SUPPORT BAR
(J) using the second 5/8” SCREW (K).
STEP 8 - PICTURE 8: NOW YOU WILLASSEMBLE THE DRAWER!
Take the FOUR METAL PINS (M) and screw them into the pre-installed threaded plastic jackets on drawer
parts N, O, and S. Screw in the pins only as deep as their threads.
H2
PICTURE 7C
PICTURE 7B
I
EJ
EF1
I
H1
PICTURE 7A
F1
*You must be sure to
use the thicker H1
shelf in the top
position.

2.0/1008/TG
N
O
P
R
PICTURE 9 PICTURE 10
S
STEP12 - PICTURE 12: Insert the drawer into the changing table. Angle the drawer so that you can slide the wheels
on the inside tracks (T) over and behind the wheels on the outside tracks (A); then holding the drawer level push it all
the way into the table. When properly installed the drawer will glide in and out smoothly and the wheels act as a stopper
to keep the drawer from falling out when fully opened.
Place the MATTRESS PAD (L) onto the TOP SHELF (H1)
underneath the SAFETY BELT (I).
PICTURE 11
T2
PICTURE 12
L
YOUR CHANGING TABLE IS ASSEMBLED!
DO NOT USE THIS PRODUCT UNTILYOU HAVE
REVIEWED THE SAFETYINSTRUCTIONS ON PAGE 2!
Remember that you can accessorize this table with up to
four Badger Nursery Baskets (sold separately)!
Browse our selection at www.badgerbasket.com! B2
B1
Page 6 of 6
STEP 9 - PICTURE 9: Insert the METAL PINS (M), and the wooden pegs, on the LEFT (N) and RIGHT SIDE
PANELS (O) into the holes on the side edges of the BACK PANEL (P). Be sure all of the shelf grooves are lined up.
Insert TWO ROUND METAL CAMS (Q) into the holes on the BACK PANEL (P) with the arrows on the cams
pointing towards the heads of the metal pins. Turn the cams clockwise using a standard screwdriver until they lock over
the heads of the pins. Insert the BOTTOM PANEL (R) into the grooves and be sure it’s seated on all three sides.
STEP 10 - PICTURE 10: Repeat the pin and cam procedure from Step 9 to attach the FRONT PANEL (S) to the
LEFT (N) and RIGHT SIDE PANELS (O). Be sure the BOTTOM PANEL (R) is properly seated in the grooves on all
four sides.
STEP 11 - PICTURE 11: With the drawer upside down, attach the TWO INSIDE DRAWER TRACKS (T1 and T2) to
the SIDE PANELS (N, O) using the pre-drilled holes and THREE ½” SCREWS (C) for each track. The wheels on the
tracks line up with the back edge of the drawer.