Badger Meter Blancett B220210 User manual

Turbine Flow Meter
B220210 Magnetic Pick-up with Preamplier
for Model 1100 and QuikSert®
TRB-UM-02248-EN-02 (December 2016) User Manual

Scope of This Manual
Page 2 December 2016TRB-UM-02248-EN-02
SCOPE OF THIS MANUAL
This manual is intended to help you install and use the Blancett B220210 magnetic pick-up
with preamplifier for Model 1100 and QuikSert turbine flow meters.
MPORTANTI
Read this manual carefully before attempting any installation or operation. Not following
instructions properly may impair safety of equipment and/or personnel. Keep the manual
accessible for future reference.
UNPACKING AND INSPECTION
Upon opening the shipping container, visually inspect the product and applicable
accessories for any physical damage such as scratches, loose or broken parts, or any other
sign of damage that may have occurred during shipment.
OTE:NIf damage is found, request an inspection by the carrier’s agent within 48 hours of
delivery and file a claim with the carrier. A claim for equipment damage in transit
is the sole responsibility of the purchaser.
INTRODUCTION
The Blancett B220210 magnetic pick-up with preamplifier was designed to directly replace
a standard pick-up within a turbine flow meter when signal amplification is required.
The pick-up is a combination of a standard Blancett magnetic pick-up and a solid state
electronic preamplifier in a single stainless steel housing.

Operating Principle
Page 3December 2016 TRB-UM-02248-EN-02
OPERATING PRINCIPLE
As fluid flows through the meter the turbine rotates at a speed proportional to the fluid
velocity. As each turbine blade passes through the magnetic field at the base of the pick-up,
an AC voltage pulse is generated in the pickup coil. The voltage signal generated by these
pulses becomes amplified within the pick-up. The output signal generated from the pick-
up is now in the form of a square wave. The frequency of this amplified signal is used to
represent the flow rate of fluid passing through the turbine flow meter.
1 IN. CONDUIT CONNECTOR
Figure 1: Model 1100 flow meter with preamplifier pick-up and connecting cable

Turbine Flow Meter, B220210 Magnetic Pick-up with Preamplier for Model 1100 and QuikSert®
www.badgermeter.com
Blancett and QuikSert are registered trademarks of Badger Meter, In. Other trademarks appearing in this document are the property of their respective entities. Due
to continuous research, product improvements and enhancements, Badger Meter reserves the right to change product or system specications without notice,
except to the extent an outstanding contractual obligation exists. © 2016 Badger Meter, Inc. All rights reserved.
The Americas | Badger Meter | 4545 West Brown Deer Rd | PO Box 245036 | Milwaukee, WI 53224-9536 | 800-876-3837 | 414-355-0400
México | Badger Meter de las Americas, S.A. de C.V. | Pedro Luis Ogazón N°32 | Esq. Angelina N°24 | Colonia Guadalupe Inn | CP 01050 | México, DF | México | [phone]
Europe, Middle East and Africa | Badger Meter Europa GmbH | Nurtinger Str 76 | 72639 Neuen | Germany | [phone]
Europe, Middle East Branch Oce | Badger Meter Europe | PO Box 341442 | Dubai Silicon Oasis, Head Quarter Building, Wing C, Oce #C209 | Dubai / UAE | [phone]
Czech Republic | Badger Meter Czech Republic s.r.o. | Maříkova 2082/26 | 621 00 Brno, Czech Republic | [phone]
Slovakia | Badger Meter Slovakia s.r.o. | Racianska 109/B | 831 02 Bratislava, Slovakia | [phone]
Asia Pacic | Badger Meter | 80 Marine Parade Rd | 21-06 Parkway Parade | Singapore 449269 | [phone]
China | Badger Meter | 7-1202 | 99 Hangzhong Road | Minhang District | Shanghai | China 201101 | [phone]
Switzerland | Badger Meter Swiss AG | Mittelholzerstrasse 8 | 3006 Bern | Switzerland | [phone]
Legacy Document Number: 02-SGN-UM-00124-EN
Control. Manage. Optimize.
INSTALLATION AND WIRING
The B220210 is simply threaded into the hole (5/8 inch – 18UNF) in the turbine meter until
the pick-up bottoms out. Tighten the pick-up finger tight. Do not over tighten.
Install the 3-pin connector in the proper orientation and connect the wire ends of the cable
using appropriate common wiring practices. Refer to the table and Figure 2 below for
wiring specifications.
Pin Description Wire Color
A Power: 5…30V DC @ 15 mA Red
B Common: Power return Black
C Output Signal: 0…10V (Square Wave) Green or Clear
0.64 DIA MAX
0.64 DIA MAX
Figure 2: Pin configuration
SPECIFICATIONS
Supply Voltage 5…30V DC
Input Current 15 mA
Current Sinking 25 mA maximum
Pulse Out 0…10V peak-to-peak
Frequency Range 5 Hz…10 kHz
Transmit Distance 1500 ft maximum
Temperature –20…160° F (–29…71° C)
Housing Stainless steel and epoxy encapsulated
Electrical Connection 3-pin straight Amphenol® connector supplied with 10 ft cable standard
(Part No. B220-219, sold separately.)