Bakfiets Q-4 T-BOX User manual

BAKFIETS
Q-4 T-BOX

1 rear frame、canopy tube、
front wheel、accessories、
canipy、leather seatand .
2left picture:
a.canopy tubex2
b.rear framex1
c.leather seatx2
d.canopyx1
e.front fenderx2
f.front wheelx2
g.saddlex1
h.hedraulic disc brake(without
disc)x1
i.seat postx1
j.safe beltx4

3bottom frame,folded plate
4left picture:
a.bottom framex1
b.folded platex4

5you can see three pats:woo
box、handlebar、accessories.
6Left picture:
a.front woodx1
b.rear woodx1
c.bottom woodx1
d.side woodx2
e.seat woodx2
7left picture:
a.front lightx2
b.foot stepx2
c.pendalx1
d.bellx1
e.damperx2
f.wheel reflectorx3
g.dscx2
h.release(∮25.4)x2
i.damper bushingx2
j.fasteners bagx1
8left photo:
a.handelbar rightx1
b.handelbar leftx1

9
a.Bearing shell(big)x1
b.Bearing shell(small)x1
c.Hammerx1
10 The bearing shell (small)
flat on the bottom frame to the
plane of the head tube, beaten
with a hammer
11 bearing shell(small) please
see the result

13 Bearing shell(big) beat out
12 10 The bearing shell (big)
flat on the bottom frame to the
plane of the head tube, beaten
with a hammer
14
a.Adjustable wrenchx1
b.M18nutx1
c.spring washerx1
d.flatx1
e.bearing (small)x1

15 Please let the rear frame
and bottom frame together,do
as picture
16 check the finished
17 put bearing(small)
18 see the finished

19 put flat mat,then put spring
washer
20 screw on M18 nut
21 lock it
22 fasteners&damper and tool ,
a.damperx2
b. damper bushingx2
c.M8X50 boltx2
d.M8 nylon nutx2
e.flat matx2
f.12#wrenchx1
g.13#wrenchx1

23 please let the damper fit
frame hole
24 put one flat,and M8 nylon
nut
25 use12#&13#扳手wrench lock
i
26 in a hole of the other
end,put the bushing

27 M8x50 bolt
28 use 13#wrench lock it
29 damper finished
30
a.flat matx1
b.M5X20 inner hexagon boltx1
c.wrenchx1

31 Please let the brake hole to
fit bottom thread,then put flat
mat,use M5*20 hexagon bolt
32 Please adjust the
position,use wrench to lock it
33
a.flat matx12
b.M6 hexagon boltx4
c.wrenchx1

34 let the cable like this
35 Leave rubber sleeve
36 use 3 flat mat

37 Fit Hexagon bolt
38 Lock it
39 assembling right brake same
as left(Attention:the cable don't
need round)

40 disc brake kit sub-pump
the following part of the
assembly after the
completion of the effect
41 Place the disc brakes on
the bottom of the bottom
frame from the bottom of the
right side

42
a.8#wrench x1
b.cross screwdriverx1
c.M5nylon nutx4
d.flat matx4
e.M5x12round cross boltx4
43 please find the fender hole on
bottom,put flat mat,fitM5x12
round cross bolt
44 use cross screwdriver&8#
wrench lock it

45 the fender finished
46 Let foot ladder top hole to fit
fender top hole,use M5x12 flat
head cross screw
47 put the falt mat on the
inside fender and M5nylon nut

48 use the cross screwdriver
&8# and wrench
49 finished foot ladder

50 let shift lever from left bottom
51 shift lever go though like this
picture

52
a.discx2
b.screwx12
c.wrench(plum flower head)x1
53 the assembling
finished(attention:whatever right
wheel or left wheel,the disc
direction same as wheel moving)
54
a.15#wrenchx1
b.3/8:flange nutx1
c.safety hookx1

55 front wheel,put safety hook,fit
3/8”flange nut
56 use15#wrench lock it
57 front wheels assembling be
finished(attention:tread patern's
arrow direction same as wheel
moving)