Balkene Home SIENA 64016 User manual

SIENA
MEDIA CONSOLE
Item#: 64016
SAVE THESE INSTRUCTIONS
FOR FUTURE REFERENCE.
10112021
Questions, problems, missing parts?
Before returning to your retailer, our Florida-based customer service team is available:
ATTACH YOUR RECEIPT
Keep a copy of your proof of purchase
or order confirmation, which will be
needed if you need to contact us about
warranty coverage.
Purchase date:
Call toll-free [phone] 9 am – 9 pm, EST
Email
Live Chat
[email protected]
www.balkenehome.com 9 am – 6 pm, EST, Monday – Friday

Á>UÁ¿É¸¿tµ¿>¸¸¸Á>Ug[¿¿£l½½¤¿lu¼l¼¼¿¿N¿¿ÑÑѦL>ggg¦U¿ ¿¿¿¿¿¿Ç
INFORMATION
BEFORE YOU BEGIN
Before beginning assembly, make sure all parts are present. Compare parts
received with the "Parts List." If any part is missing or damaged, do NOT attempt
to assemble the product. Please read and understand this entire manual before
attempting to assemble this product. If you have any questions regarding the
product, please contact Customer Service.
GENERAL INFORMATION
This product is made of particle board and MDF. For safe assembly, work on a
dry, soft, secure, and clean surface. Do not clean with detergents or chemicals.
Do not sit or stand on the unit. Do not place damp or hot items such as coffee
cups directly on the surface of this item. Keep away from direct sunlight and
water. Do not drag the unit. For indoor use only.
SAFETY INFORMATION
WARNING
DO NOT sit or stand, or allow children to sit or stand on the assembled product.
Make sure connectors are securely in place. Perform periodic checks to ensure
the connectors remain secure and adjust if needed. Keep unassembled parts and
hardware away from children and infants. This package contains small parts and
sharp edges. Adult assembly required.
CAUTION
READ all instructions before beginning assembly. Failure to do so may result in
faulty assembly and potential injury. Assemble the item on a soft, nonabrasive
surface such as carpet or cardboard to avoid damaging the item.
Max safe load limit:
Top: 20 KG / 44 LB
Open Shelf: 8 KG / 17.5 LB
Drawer: 5 KG / 11 LB
Side compartments: 8 KG/ 17.5 LB
Call toll-free [phone] 9 am – 9 pm, EST
Email
Live Chat
[email protected]
www.balkenehome.com 9 am – 6 pm, EST, Monday – Friday

Á>UÁ¿É¸¿tµ¿>¸¸¸Á>Ug[¿¿£l½½¤¿lu¼l¼¼¿¿N¿¿ÑÑѦL>ggg¦U¿ ¿¿¿¿¿¿Ã
PARTS LIST
A
C
E
B
F
PART DESCRIPTION QTY
ATop Panel
BLeft Side
CRight Side
DLeft Divider
ERight Divider
1
1
1
1
1
FBase Panel
GBottom Face Frame
1
1
PART DESCRIPTION QTY
I
Top Face Frame
J
Door Rail
K
Support Leg
L
Shelf
M
Side Backer Panel
1
1
1
1
2
N
Top Backer Panel
Bottom Backer Panel
1
1
PART DESCRIPTION QTY
Q
Left Door
R
Right Door
S
Drawer Front
T
Drawer Back
U
Left Drawer Side
1
1
1
1
1
Right Drawer Side 1
Drawer Bottom 1
D
H O
P
G
J
K
H
N
P
O
I
L
M
R
S
T
Q
U
L

Á>UÁ¿É¸¿tµ¿>¸¸¸Á>Ug[¿¿£l½½¤¿lu¼l¼¼¿¿N¿¿ÑÑѦL>ggg¦U¿4
HARDWARE CONTENTS
1
Cam Bolt
6x35mm
Qty: 23
YOU WILL NEED FOR ASSEMBLY:
(not included)
Phillips-head screwdriver
Mallet or hammer
2
Cam Nut
Qty: 23
3
Dowel
8x30mm
Qty: 31
4
Hex Bolt
6x18mm
Qty: 3
5
Handle
Qty: 2
7
Runner
Qty: 2
8 9
Track Pin
Qty: 2
Screw
4x35mm
Qty: 8
Screw
4x12mm
Qty: 8
Screw Bolt
4x12mm
Qty: 4
Screw Bolt
4x10mm
Qty: 2
Screw
5x40mm
Qty: 1
Foot Pad
Qty: 1
6
Hanger Roller
Qty: 4
Qty: 5
Screw Bolt
4x18mm
Qty: 4
Screw
3x12mm
Qty: 6
Screw
4x65mm
Qty: 4
Screw
3x16mm
Qty: 12
Corner Bracket
Qty: 12
Hex Wrench

Á>UÁ¿É¸¿tµ¿>¸¸¸Á>Ug[¿¿£l½½¤¿lu¼l¼¼¿¿N¿¿ÑÑѦL>ggg¦U¿¿¿¿¿5
ASSEMBLY
1Insert Cam Bolts 1 into the 2 indicated holes in
the Bottom Face Frame G. Use a Phillips-head
screwdriver to tighten the threads into the
panels.
Hardware Required: 1 Cam Bolt x3
Insert Dowels 3 into the 2 remaining holes
in the Bottom Face Frame G.
Insert the hardware in the Bottom Face Frame
into the corresponding holes in the edge of the
Base Panel F as shown. Secure by inserting a
Cam Nut 2 into each of the adjoining holes in
the underside of the Base Panel. (HINT: the
small arrow on the flat side of the Cam Nut
should point toward the adjoining panel.)
Use a Phillips-head screwdriver to turn the
Cam Nuts clockwise to secure the Cam Bolts.
Hardware Required: 2 Cam Nut x3
3 Dowel x2
Install the Support Leg J on the bottom of the
Bottom Panel F using a Screw ? as shown.
Apply a Foot Pad ? to the bottom of the
Support Leg. Press firmly to adhere.
Hardware Required: ? Screw (5x40mm) x1
? Foot Pad x1
3
F
3
2
2
J
F
1
G
3
G
→→
2
ASSEMBLY NOTE: Use a Phillips-
head screwdriver to tighten each
Cam Bolt you install until its
threads are fully inserted.

Á>UÁ¿É¸¿tµ¿>¸¸¸Á>Ug[¿¿£l½½¤¿lu¼l¼¼¿¿N¿¿ÑÑѦL>ggg¦U¿6
ASSEMBLY
4
5Place Dowels 3 in the 2 innermost holes on either
side of the Bottom Shelf K.
Insert the Cam Bolts 1 previously installed in the
Left Divider D into the corresponding holes in the
edge of the Bottom Shelf as shown. Secure by
inserting a Cam Nut 2 into each of the adjoining
holes in the underside of the Bottom Shelf. Use a
Phillips-head screwdriver to turn the Cam Nuts
clockwise to secure the Cam Bolts.
Attach the Right Divider E to the Bottom Shelf
using the same method.
Install the Drawer Runners 7 on the Left and Right Dividers D/E.
Hardware Required: 2 Cam Nut x4
3 Dowel x4
7
8
FRONT BACK
Fully extend the runner to uncover
the mounting holes. After attaching
the runner to the panel, push runner
back into the closed position.
8 8
7
8
FRONT
BACK
88
FRONT
BACK
1
D8
Hardware Required: 1 Cam Bolt x4
7 Runner x2
8 Screw (3x12mm) x6
Fully extend one Runner and align the inner section along the 3 small holes on the Left Divider. Verify that the
orientation of the Runner matches the diagram, then fasten the Runner to the Divider using 3 Screws 8
positioned as shown. Once the Runner is attached, slide it back to the closed position.
Attach the second Runner to the Right Divider E following the same method, checking orientation before
inserting Screws.
Insert Cam Bolts 1 into the 2 indicated holes above the Runners on each Divider.
E
3
7
E
1
8
7
FRONT
BACK
K
D
3
2
2

Á>UÁ¿É¸¿tµ¿>¸¸¸Á>Ug[¿¿£l½½¤¿lu¼l¼¼¿¿N¿¿ÑÑѦL>ggg¦U¿7
ASSEMBLY
6
7
Slide the Bottom Backer Panel N into the groove
behind the Runners 7.
Place Dowels 3 in the 2 center-most holes in the
bottom edges of both the Left and Right
Dividers D/E.
Insert the installed Dowels into the
corresponding holes on the top of the Base
Panel F.
Secure the components together by inserting 4
Screws ? through the bottom of the Bottom
Panel and into the Dividers.
8
F
D
Hardware Required: 3 Dowel x4
? Screw (4x35mm) x4
Insert Cam Bolts 1 into the Left and Right
Sides B/C.
Apply Foot Pads ? to the bottom of each leg.
Press firmly to adhere.
Hardware Required: 1 Cam Bolt x4
? Foot Pad x4
E
3
3
N
B
C
1
1
F
C
2
3
Insert 3 Dowels 3 into the Right Side C as
indicated.
Attach the Right Side to the partially-assembled
unit by inserting the installed Dowels and Cam
Bolts into the right edge of the Base Panel F.
Secure by inserting a Cam Nut into each of the 2
adjoining holes in the underside of the Base
Panel. Use a Phillips-head screwdriver to turn the
Cam Nuts to secure the Cam Bolts.
Hardware Required: 2 Cam Nut x2
3 Dowel x3

Á>UÁ¿É¸¿tµ¿>¸¸¸Á>Ug[¿¿£l½½¤¿lu¼l¼¼¿¿N¿¿ÑÑѦL>ggg¦U¿8
ASSEMBLY
9
10
Attach the Door Rail I to the Top Face Frame H
using 3 Hex Bolts 4. Use the Hex Wrench ? to
tighten each Hex Bolt.
Hardware Required: 4 Hex Bolt (6x18mm) x3
?Hex Wrench
4
Insert 2 Dowels 3 into the each end of the
Top Face Frame H. Slide the Top Face
3
3
3
3
F
B
C
2
Hardware Required: 2 Cam Nut x2
3 Dowel x7
in the underside of the Top Panel A.
Hardware Required: 1 Cam Bolt x8
11Insert a total of 8 Cam Bolts 1 into the indicated holes
1
H
I
4
H
Frame into place on the partially-
assembled unit as shown, inserting the
Dowels into corresponding holes on the Right
Side.
Insert 3 more Dowels into the remaining holes
along the bottom edge of the Left Side B.
Attach the Left Side to the partially-assembled
unit by sliding the Cam Bolts 1 into the
corresponding holes in the left edge of the
Base Panell F while inserting the Dowels on
the free end of the Top Face Frame into the
Left Side panel. Fasten the Cam Bolts by
inserting a Cam Nut into each of the 2
adjoining holes at the underside of the Base
Panel. Use a Phillips-head screwdriver to turn
the Cam Nuts clockwise.
A

Á>UÁ¿É¸¿tµ¿>¸¸¸Á>Ug[¿¿£l½½¤¿lu¼l¼¼¿¿N¿¿ÑÑѦL>ggg¦U¿¿¿¿¿¿¿9
ASSEMBLY
Insert 11 Dowels 3 in the top edges of the
Left Side B, Center Panel D, Right Side C,
and Top Face Frames H.
Hardware Required: 2 Cam Nut x8
3 Dowel x11
? Screw (4x65mm) x4
12
A
3
B
With runner side facing out, attach the Left
Drawer Side S to the Drawer Back R using 2
Screws ?. Ensure that the narrow groove at
13
Hardware Required: ? Screw (4x35mm) x4
Insert Cam Bolts 1 into the indicated holes
in each Drawer Front Q. Tighten the threads
fully into the panels using a Phillips-head
screwdriver.
1 Cam Bolt x4
14
Q
1
1
Hardware Required:
2
2
H
L
M
L
R
S
T
the bottom runs continuously along the inside of
both pieces.
Repeat to attach the Right Drawer Side T to the
Drawer Back.
Lower the Top Panel A into place by inserting the
Cam Bolts 1 into the top edges of the vertical
panels. Secure by inserting a Cam Nut 2 into each
of the adjoining holes near the tops of the vertical
panels. Use a Phillips-head screwdriver to turn
the Cam Nuts clockwise to secure the Cam Bolts.
Insert 2 Screws ? through the bottom of each of
the Top Face Frames and into the Top Panel.
Tighten with a Phillips-head screwdriver.

Á>UÁ¿É¸¿tµ¿>¸¸¸Á>Ug[¿¿£l½½¤¿lu¼l¼¼¿¿N¿¿ÑÑѦL>ggg¦U¿10
ASSEMBLY
15
16
Hardware Required: 2 Cam Nut x4
2
Slide the Drawer Bottom U into place in the
groove in the drawer panels.
To install the drawer, fully extend both Drawer
Runners 7 and slide the drawer into place
between them. Secure the Runners to the
Hardware Required: ? Screw Bolt (4x10mm) x2
U
2
T
Q
S
Insert the Cam Bolts in the Drawer Front Q into
the front edges of the Drawer Sides. Secure by
inserting a Cam Nut 2 into each of the adjoining
holes on the outside of the Drawer Sides. Use a
Phillips-head screwdriver to turn the Cam Nuts
clockwise to secure the Cam Bolts.
Q
7Q
sides of the Drawer using 2 Screw Bolts ?.
17
Insert 2 Track Pins 9 in the top edge of the Bottom
Face Frame G, one in front of each Divider D/E.
Hardware Required: 9 Track Pin x2
9
G
E
D

Á>UÁ¿É¸¿tµ¿>¸¸¸Á>Ug[¿¿£l½½¤¿lu¼l¼¼¿¿N¿¿ÑÑѦL>ggg¦U¿11
ASSEMBLY
18
Hardware Required:
Attach a Handle 5 to each Door O/P using 2 Screw Bolts 6.
Attach 2 Hanger Rollers ? to each Door as shown using 2 Screws ? per Roller.
5
6
5 Handle x2
6 Screw Bolt (4x18mm) x4
? Hanger Roller x4
? Screw (4x12mm) x8
6
O
P
5
19 Hang each Door O/P by resting the
wheels of the Roller Hangers ? on
top of the Door Rail I and settling the
track on the bottom edge of the door
onto the Track Pin 9.
P
O
9
I

Á>UÁ¿É¸¿tµ¿>¸¸¸Á>Ug[¿¿£l½½¤¿lu¼l¼¼¿¿N¿¿ÑÑѦL>ggg¦U¿12
ASSEMBLY
20
Hardware Required:
Secure each Roller Hanger ? to the Door
Rail I using a Screw Bolt ? as shown.
? Screw Bolt (4x12mm) x4
21 Install the Corner Brackets ? at each corner of the Side
and Top Backer Panels L/M by inserting a Screw ?.
I
Hardware Required: ? Corner Bracket x12
? Screw (3x16mm) x12
L
M
L
Your Siena Media Console is ready for use!

LIMITED WARRANTY
Customers in the Contiguous US
With proof of purchase from an authorized retailer, this product is warranted
for a period of 1 year from original purchase date against defects in materials
and workmanship under normal use. This warranty does NOT cover normal
wear/weathering, exposure to water, freezing temperatures, oils, fluids, or
chemicals OR use in a commercial context if the unit is not designated as a
commercial model. At Well Traveled Living’s sole discretion, products under
warranty will be repaired and/or replaced at no charge to the customer.
Returns sent back to Well Traveled Living must be sent via prepaid freight in
the original retail packaging.
For warranty service, contact Balkene Home/Well Traveled Living at the
address, phone numbers or website and email listed in this owner’s manual.
Be sure to have your sales receipt, date of purchase and catalogue/model
numbers available when calling. All warranty service will be coordinated by
Well Traveled Living's Amelia Island, Florida service center. This warranty is
extended only to the original owner. Proof of purchase will be required before
warranty service is rendered. The sales receipt is the only valid proof of
purchase. This warranty only covers failures due to defects in materials or
workmanship which occur during normal use. Failures and/or damage which
result from accident, negligence, misuse, abuse, neglect, mishandling,
alteration or modification, failure to maintain, improper assembly or
maintenance, service by unauthorized agency or use of unauthorized
components or damage that is attributable to acts of God are NOT covered.
This limited warranty gives you specific legal rights and you may also have
other rights which vary from jurisdiction to jurisdiction. The provisions of the
United Nations Convention on Contracts for the Sales of Goods shall not apply
to this limited warranty or the sale of products covered by this limited
warranty.
• THERE ARE NO EXPRESS WARRANTIES EXCEPT AS
LISTED.
• PURCHASER ASSUMES ALL RISKS IN THE
ASSEMBLY AND OPERATION OF THIS UNIT.
• FAILURE TO FOLLOW WARNINGS AND
OPERATIONAL INSTRUCTIONS CONTAINED IN
THIS MANUAL CAN RESULT IN SEVERE PROPERTY
DAMAGE AND/OR PERSONAL INJURY.
• IN NO EVENT WILL WELL TRAVELED LIVING, OR
ITS DIRECTORS, OFFICERS OR AGENTS BE LIABLE
TO THE PURCHASER OR ANY THIRD PARTY,
WHETHER IN CONTRACT, IN TORT, OR ON ANY
OTHER BASIS, FOR ANY INDIRECT, SPECIAL,
PUNITIVE, EXEMPLARY, CONSEQUENTIAL, OR
INCIDENTAL LOSS, COST, OR DAMAGE ARISING
OUT OF OR IN CONNECTION WITH THE SALE,
MAINTENANCE, USE, OR INABILITY TO USE THE
PRODUCT, EVEN IF WELL TRAVELED LIVING OR
ITS DIRECTORS, OFFICERS OR AGENTS HAVE BEEN
ADVISED OF THE POSSIBILITY OF SUCH LOSSES,
COSTS OR DAMAGES, OR IF SUCH LOSSES, COSTS,
OR DAMAGES ARE FORESEEABLE. IN NO EVENT
WILL WELL TRAVELED LIVING, OR ITS OFFICERS,
DIRECTORS, OR AGENTS BE LIABLE FOR ANY
DIRECT LOSSES, COSTS OR DAMAGES THAT
EXCEED THE PURCHASE PRICE OF THE PRODUCT.
• SOME JURISDICTIONS DO NOT ALLOW THE
EXCLUSION OR LIMITATION OF INCIDENTAL OR
CONSEQUENTIAL DAMAGES, SO THE ABOVE
LIMITATION OR EXCLUSION MAY NOT APPLY TO
THE PURCHASER.
Important Notice
Do NOT return to place of purchase—for customer service and warranty issues: Distributed by:
Well Traveled Living
716 S 8th Street, Amelia Island, FL 32034
balkenehome.com
[email protected]
[phone]
Fire Sense®, Patio Sense,® Avalon Home,® Mojave Sun®, Vulcan®, Balkene Home® and Well Traveled Living® are registered trademarks of
Well Traveled Imports, Inc®. All assembly instruction presentations are the property of Well Traveled Imports, Inc.
® and are protected by
U.S. copyrights and trademarks. All rights reserved.
EXTEND YOUR WARRANTY
When you purchase a Fire Sense or Balkene Home product from any authorized retailer, you'll have peace
of mind in knowing that it comes with a one-year warranty. Extend your warranty for an additional year
when you review your item at balkenehome.com within 365 days of purchase.
Call toll-free [phone] 9 am – 9 pm, EST
Email [email protected]
Live chat balkenehome.com 9 am – 6 pm, EST, Mon – Fri