Bambu Lab P1S User manual

3D Printer
Quick Start
Please review the entire guide before operating the printer.
Safety Notice: Do not connect to power until assembly is complete.
P1S

Belt Tensioner
Bambu Bus
Excess Chute
Power Socket
Component Introduction
Tool Head
Pause
Screen
SD Card
Air Filter
Back
USB
Build Plate
Cooling Fan
Chamber
Camera

Screen Spool Holder Spare Hot End Nozzle Wiping
Pad
Power Cord PTFE Tube Allen Key H1.5
Allen Key H2
Unclogging Pin Tool
Build Plate
（ Pre-installed）
Filament
H1.5
H2
Bambu Scraper

Tool Head Unlock

Attention:
Spool Holder Assembly
Secure the spool holder with two screws fromRemove the screws as pictured with an Allen
Key H2.

into the terminal as pictured.
2
Attention: Bend the LCD cable towards the
opening on the back of the screen as pictured.
Inset the screen back to the slot on the printer,
then lock it by pushing it to the left.
4
Hot Bed Unlock & Screen Installation
Remove the three screws with an Allen
Key H2 to unlock the hot bed.
1
3

QR Code
DO NOT remove the protective foam from beneath the hot bed until after the initial calibration is complete.
3. Use Bambu Handy to scan the QR code on the screen, and bind your printer with your Bambu Lab
account.
4. Follow the instructions on the screen to complete the initial calibration.
It is normal to have vibration and noise during the calibration process.
2. Connect the printer to power. Follow the instructions on
the screen until getting to the page shown on the right side.
1. Download the Bambu Handy App. Register and log in
to your Bambu Lab account.
Printer Binding
Bambu Handy
Download
P1S
P1S
P1S
1 2 3

1 2
Select " "-" ", and heat the nozzle to the
Select " "-" "-" " several times until the
pulled out from the PTFE tube anchor manually.
print.
3
First Print

Download Bambu Studio: https://bambulab.com/en/download/studio
Log in to Bambu Studio with your Bambu Lab account, which is the same for the Bambu Online store.
Create or open a project.
Bambu Studio

Slice the model, select your printer and send the model to print.
Bambu Studio
P1S
P1S
PLA Plate

During printing, you can remotely monitor your print, or pause/stop printing on the
P1S
Bambu Studio

Fused Deposition Modeling
Body
Build Volume(W*D*H) 256*256*256 mm³
Chassis Steel
Plastic & GlassShell
Toolhead
Hot End All-Metal
Extruder Gears Steel
Nozzle Stainless Steel
Max Hot End Temperature 300
100
Nozzle Diameter (Included) 0.4 mm
Nozzle Diameter (Optional) 0.2 mm, 0.6 mm, 0.8 mm
Filament Cutter Yes
Filament Diameter 1.75 mm
Compatible Build Plate
Bambu Textured PEI Plate
Bambu Cool Plate
Bambu Engineering Plate
Bambu High Temperature Plate
Max Build Plate Temperature
Speed
Heatbed
Max Speed of Toolhead 500 mm/s
Max Acceleration of Toolhead 20 m/s²
Max Hot End Flow
Cooling
Hot End Fan
Closed Loop Control
Control Board Fan
Closed Loop Control
Chamber Temperature Regulator Fan
Closed Loop Control
PCooling Fan
Closed Loop Control
Closed Loop Control
Air Filter Activated Carbon Filter
PLA, PETG, TPU, ABS, ASA, PVA, PET
PA, PC
Ideal
Capable
Carbon/Glass Fiber Reinforced Polymer Not Recommended
Sensors
Chamber Monitoring Camera Low Rate Camera 1280 x 720 / 0.5fps ,
Timelapse Suppoed
Yes
Filament Run Out Sensor
YesPower Loss Recover
Optional with AMS
Printing Technology
Item

https://bambulab.com/download
Bambu Studio
Bambu Handy
Electrical Requirements
100-240 VAC, 50/60 Hz
Max Power
Input Voltage
USB Output Power
Electronics
Display
5V/1.5A
Connectivity
2.7-inch 192x64 Screen
Storage
Wi-Fi, Bluetooth, Bambu-Bus
Micro SD Card
Control Int
Motion Controller
Button, APP, PC Application
Software Slicer
Bambu Studio
G-code such as Superslicer, Prusaslicer and Cura,
Slic MacOS, Windows
Bluetooth
Frequency Band
Frequency Range
Transmitter Power（EIRP)
2412MHz-2472MHz(CE)
2412MHz-2462MHz(FCC)
2400MHz-2483.5MHz(SRRC)
Protocol
Protocol
≤21.5dBm(FCC)
≤20dBm(CE/SRRC)
IEEE802.11 b/g/n
Transmitter Power（EIRP）
2402MHz-2480MHz(CE/FCC)
2400MHz-2483.5MHz(SRRC)
≤20dBm(FCC/SRRC)
<10dBm(CE)
BLE5.0
1000W@220V, 350W@110V
Physical Dimensions Dimensions(W×D×H) 389*389*458mm³
Net Weight 12.95kg

Please visit the Bambu Lab Wiki for more setup and
maintenance tutorials.
https://wiki.bambulab.com/en/home
Approach 1:
Approach 2:
Bambulab
Wiki

Enjoy!
www.bambulab.com