Bambu Lab X1 Combo User manual

3D Printer
Quick Start
Please review the entire guide before operating the printer.
Safety Notice: Do not connect to power until assembly is complete.

*Warning:
TPU Damp PVA Cardboard
Spool
The AMS suppos spools with a width of 50-68mm.
When operating the AMS, we recommend using Bambu Filament, which has been thoroughly
tested to work with the AMS. Please make sure to avoid using soft materials like TPU or damp
PVA, as they can get stuck in the AMS, and please avoid using cardboard spools as the spool
may slip. If you run into any issues with specic laments, please let us know so that we can
provide better advice to our community.

Tool Head
Touch Screen
Air Filter
Bambu Micro Lidar
PTFE Tube
Belt Tensioner
Bambu Bus
Cable 4-Pin
Excess Chute
Power Socket
Chamber Camera
(X1-Carbon Only)
Glass Cover Plate
Build Plate
Auxilia Pa
Cooling Fan
(X1-Carbon Only)
Component Introduction
Pause
Screen Sleep/Wake

Filament Outlet
Buckle
Bambu Bus Cable 6-Pin Inteace
Desiccant
Filament Inlet

Touch Screen Spool Holder Spare Hot End Nozzle Wiping
Pad (x2)
Power Cord Spare Filament
Cutter (x2) Allen Key H1.5 Allen Key H2
H1.5
H2
Unclogging Pin
Tool
Flexible Build Plate
(Pre-installed on
build plate)
Spare Sheet for
Bambu Cool Plate (x2) Bambu Scraper Glue Stick for Build Plate
250g Filament (x3)
Bambu Bus Cable-4Pin
Bambu Bus Cable-6Pin
Accesso Specication

1 2
Take out the accesso box. Use Allen Key H2
to remove the screws as pictured.
Take out the AMS by sliding it out through
the top.
AMS & Tool Head Unlock
（Allen Key H2）
*We recommend using the sho end of the Allen Key to unlock the screws more easily.

4
Take out the AMS cushioning.
Remove the four screws as the arrows indicate.
3
Remove the carboard from the tool head.
Romove the foam from the excess chute.
（Allen Key H2）
5

AMS Assembly
550mm PTFE Tube
370mm PTFE Tube
*The cable-6pin can be plugged into either inteace.
Bambu Bus Cable-6Pin Bambu Bus Cable-4Pin

Secure the spool holder with two screws from
the accesso box.
Spool Holder Assembly
21
*The spool holder is only necessa when printing with laments that are not suppoed for use with the AMS.
Remove the screw as pictured with an
Allen Key H2.
（Allen Key H2）

Pull the Flexible Printed Circuit（FPC) out
about 50mm.
Inse the screen back to the slot on the
printer, then lock it by pushing it to the left.
Inse the FPC into the po by pressing the
terminal as pictured.
Screen Installation
12
3

Hot Bed Unlock
Remove the three screws with an Allen Key H2 to unlock the hot bed. Connect the printer to
power. Follow the instructions on the screen to complete the initial calibration.
DO NOT remove the protective foam from beneath the hot bed until after the initial calibration is complete.
（Allen Key H2）

Place at least one spool of Bambu Filament
into the AMS. Turn on the power to sta the
printer and the AMS. Inse the lament into
the lament inlet. The lament will be
automatically pre-loaded when detected.
*We recommend rst printing a single-color model
with the supplied Bambu PLA Basic.
Apply a thin layer of glue on the build plate.
First Print
Press " " - "internal". Select a le to sta the
rst print.
*We recommend using one of the pre-loaded les as a
rst test print.

X1-Carbon X1
Fused Deposition Modeling
Body
Build Volume(W*D*H) 256*256*256 mm
Chassis Steel
Shell Aluminum & Glass
Tool Head
Hot End All-Metal
Extruder Gears Hardened Steel Steel
Nozzle Hardened Steel Stainless Steel
Max Hot End Temperature 300
Nozzle Diameter (Included) 0.4 mm
Nozzle Diameter (Optional) 0.2 mm, 0.6 mm, 0.8 mm
Filament Cutter Yes
Filament Diameter 1.75 mm
Hot bed
Build PlateFlexible Steel Plate
Build Plate Suace(Included) Bambu Cool Plate, Bambu Engineering Plate
Build Plate Suace (Optional) Bambu High Temperature Plate
Max Build Plate Temperature 110℃@220V， 120℃@110V
Speed
Max Speed ofTool Head 500 mm/s
Max Acceleration ofTool Head 20 m/s^2
Max Hot End Flow 32 mm^3/s @ABS
Cooling
Pa Cooling Fan Closed Loop Control
Hot End Fan Closed Loop Control
Control Board Fan Closed Loop Control
Chamber Temperature Regulator Fan Closed Loop Control
Auxilia Pa Cooling Fan Closed Loop Control Optional
Air Filter Activated Carbon Filter Optional
Suppoed Filament
PLA, PETG, TPU,ABS,ASA,PVA,PET Yes
PA, PC Ideal Capable
Carbon/Glass Fiber Reinforced Polymer Ideal Not Recommended
Sensors
Bambu Micro Lidar Yes
Chamber Monitoring Camera 1920*1080 Included Optional
Door Sensor Yes
Filament Run Out Sensor Yes
Filament Odomet Optional with AMS
Power Loss Recover Yes
Specication
Plastic & Glass
Printing Technology
Item Specication

https://bambulab.com/download
Bambu Studio
Bambu Handy
Electrical Requirements Voltage 100-240 VAC, 50/60 Hz
Max Power
Electronics
Display 5-inch 1280*720 Touch Screen
Connectivity Wi-Fi,Bambu Bus
Storage 4GB EMMC and Micro SD Card Reader
Control Inteace Touch Screen, APP, PC Application
Motion Controller Dual-Core Coex M4
Application Processor Quad ARM A7 1.2 GHz
Neural-NetworkProcessing Unit 2 Tops
Software
Slicer
Bambu Studio
Suppo third pay slicers which expo standard
G-code such as Superslicer, Prusaslicer and Cura,
but ceain advanced features may not be suppoed.
Slicer Suppoed OS MacOS, Windows
Wi
Frequency Range 2400MHz-2483.5MHz
Transmitter Power（EIRP) ≤ 21.5dBm(FCC)
≤ 20 dBm（CE/SRRC)
Protocol 802.11b/g/n
Laser
(Class 2)
Wavelength 405nm, 808nm
Maximum Output of Laser Radiation <1mW
1000W@220V, 350W@110V
Physical Dimensions Dimensions 389*389*457mm
Net Weight 14.13kg 13.18kg

Please visit Bambu Lab Wiki to learn more setup and maintetance tutorials.
https://wiki.bambulab.com/en/home
If you need suppo, please t either of the two approaches:
Approach 1: Creat a suppo ticket on Ocial Website
Approach 2: Create a suppo ticket on Bambu Handy App

Enjoy!
www.bambulab.com