Bartec Tech500 User manual

Tech 500 User Guide rev1.0 JUNE 2013
1
TABLE OF CONTENTS
IMPORTANT NOTICES 2
BEFORE YOU GET STARTED 3
TOOL LAYOUT 4
TOOL CONNECTIONS 5
POWER ON/OFF 6
CHARGING TOOL 7
TOOL DISPLAY AND ICONS 8
MENU SYSTEM
TEST BEFORE YOU TOUCH
RELEARN
REVIEW DATA
TOOLKIT
MY TOOL 11
TOOL POSITIONING/READING A SENSOR 20
UPDATING YOUR TOOL (PC) 29
UPDATING YOUR TOOL (SD Card) 32
UPDATING YOUR TOOL (Wireless)
APPENDIX A: INDUCTIVE CHARGING
APPENDIX B: VIN 37
APPENDIX C: FAQ’S & TROUBLESHOOTING GUIDE 38
APPENDIX D: DEFINITIONS 39
APPENDIX E: TPMS SYSTEM REVIEW 40
APPENDIX F: COMS ERROR TROUBLESHOOTING 42
APPENDIX G: Technical Support 43
LIMITED WARRANTY 44
TOOL REGISTRATION 47

Tech 500 User Guide rev1.0 JUNE 2013
2
INCLUDED IN Tech500 KIT:
Tech500 TPMS Tool [with protective Boot]
SD Card [in the tool]
Power Supply
Re-Learn Magnet
USB Cable
DB15 to OBDII Cable
Tech500 Quick Start Guide
Tech500 User Guide
Kit CD
IMPORTANT NOTICES
All specifications, illustrations and information contained within this manual are based on the
most current information available at the time of publication. BartecUSA reserves the right to
make changes at any time without obligation to notify any person or organization. BartecUSA
will do its best to keep you the customer informed of any changes that might affect the tools
performance.
FCC Compliance Model: DSW
FCC ID: SX8T500 IC: 5736A-T500
Contains FCC ID: QOQWT12 IC: 5123A-BGTWT12A
Contains FCCID: YOPGS1011MIP IC: 9154A-GS1011MIP
This device complies with Part 15 of the FCC Rules and with Industry Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2)
This device must accept any interference received, including
interference that may cause undesired operation.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux
appareils radio exempts de licence. L'exploitation est autorisée aux deux
conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2)

Tech 500 User Guide rev1.0 JUNE 2013
3
l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi,
même si le brouillage est susceptible d'en compromettre le fonctionnement.
Note: Changes or modifications not expressively approved by the party
responsible for compliance could void the user's authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits for
a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when
the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user
will be required to correct the interference at their expense.
BEFORE YOU GET STARTED
Before you get started using your Tech500 TPMS tool, there are a few items to review.
Charge your tool
The Tech500 is shipped with a fully charged battery, but due to shelf drain it may require
charging. It is recommended to charge your tool 2+ hours before use. (See page 6 for charging
instructions)
Register your tool
You can register your Bartec
Tech500 @ www.bartecusa.com.
Follow the on-screen prompts filling
in your information and tool serial

Tech 500 User Guide rev1.0 JUNE 2013
4
number. A valid serial number and supplier is required to process your registration, which can
take up to 24hrs once submitted.
Update your Tool
Once your tool is registered, verify the software level loaded to the level available online and
update your tool if necessary. Refer to section on tool updating for further instruction.
TOOL LAYOUT
TOOL CONNECTIONS

Tech 500 User Guide rev1.0 JUNE 2013
5
POWER ON/OFF SEQUENCE
The Tech500 is powered up using the ON/OFF key.
On/Off Key
To power the unit on press the On/Off Key for approx 2 seconds –the display will light showing
a logo and software version.
The unit will then display the Main Menu. All data (results and settings) from previous tests is
reloaded.

Tech 500 User Guide rev1.0 JUNE 2013
6
Power down the Tech500 by using the same ON/ OFF key.
On/Off Key
(Hold, then release when ‘Goodbye’ is displayed.) Auto power off is after 5 minutes of
inactivity.
The unit automatically powers up when the charger or USB port is in use- auto power off is not
operational.
CHARGING TOOL
NOTICE: Only use the power supply or USB cable that is included in the Tech500 tool kit to
charge this tool. The use of un-approved power supplies may damage your tool and will void
the tool warranty.

Tech 500 User Guide rev1.0 JUNE 2013
7
The Tech500 comes with the rechargeable battery already installed. Battery replacement must
be done at the factory.
For optimum performance, always keep your Tech500 sufficiently charged. It is recommended
that you charge the tool 2 + hours before first use.
The charge port is located on the right side of the tool and is the USB port opening.
TOOL DISPLAY AND ICONS
# of selections
# of selections
USB indicator
Data stored on tool
Battery indicator

Tech 500 User Guide rev1.0 JUNE 2013
8
The menu page number (e.g. x/y) on the status line indicates the menu page or item currently
displayed. The first number- x- indicates the item number selected. The second- y- indicates the
total number of items available.
USB Indicator
This status line indicator confirms the Tech500 is connected to the USB port of a computer.
Once communication has been established, results data can be viewed on the pc via the Mass
Storage Device feature. (Use the PC explorer program) “HTM File”
When the USB lead is removed the USB icon will disappear.
Battery Indicator/ Charging
This status line Indicator will illustrate the remaining charge status of the battery.
As different TPM types will ‘use up’ differing amounts of energy, the indicator can only provide
estimates of remaining life left before a recharge is required.
FULL Charge
Partial Charge - charging shortly is
suggested.

Tech 500 User Guide rev1.0 JUNE 2013
9
Little power in the battery- charging
required.
The battery is FLAT, requires
charging
When the battery is being charged the indicator segments ‘walk;’ from left to right.
When there is an insufficient amount of power remaining in the battery, the Tech500 will flash
its battery icon for two seconds, save all of the TPM Data and then power itself off.
Results Data Available Indicator
Indicates TPM data is available for viewing on the screen (using the View TPM Data command
from the main menu) or via a PC when the Tech500 is in its Mass Storage Device mode. (See
Section on Audit Mode)

Tech 500 User Guide rev1.0 JUNE 2013
10
When there is no data present, the TPM Data Indicator will not be visible.
To Access the Audit Data, connect your tool to the PC using the supplied USB Cable.
MENU SYSTEM
The Tech500’s menu system provides a hierarchy of instructions and commands. The top line of
the display will always indicate the current menu selected. The home key will always return to
the Main Menu screen- with ‘Select by Vehicle’ highlighted.
Current report
Archived reports

Tech 500 User Guide rev1.0 JUNE 2013
11
Menu Navigation
The menu system is navigated by the directional keys:
Up Arrow Key
Navigates up within the current menu
Down Arrow
Key
Navigates down within the current
menu
ENTER Key
Navigates to the next menu or actions
the currently selected item
Back/ESC Key
Navigates to the previous menu item
All menus wrap around. The enter key will primarily move to a sub menu.
TEST Key
Commence a TPM test. Only works on
Audit Screen
Home Key
Always returns to the Home Menu
Home Menu
This is the main screen- providing access to the main functional items of the Tech500.

Tech 500 User Guide rev1.0 JUNE 2013
12
1. Test Before You Touch
This Item is a sub menu, pressing the Enter Key will take the user to the “Test Before
You Touch” menu. The user should select the vehicle make, model and year. Used when
doing a pre-service scan.
2. Relearn
This Item is a sub menu, pressing the Enter Key will take the user to the “Test Before
You Touch” menu. The user should select the vehicle make, model and year. Used when
relearning the sensor ID’s to the vehicle.
3. Review Data
This item is a sub menu, pressing the Enter Key will take the user to the results screens.
Press directional arrows to examine the required results.
4. Toolkit
A sub-menu in which you will find your options for EZ sensor, RKE monitor, and UHF
monitor.
5. My Tool
Sub-menu containing important info about the tool itself.
Operations Screen
This screen is where you will complete all sensor testing and relearn steps.
TBYT/Relearn Toolkit
View Vehicle Info
Review Vehicle Data

Tech 500 User Guide rev1.0 JUNE 2013
13
Possible Scenarios
Successful Sensor Read
TPMS sensor was successfully activated and decoded. Displays pressure at wheel location.
Wrong Sensor Type
A TPMS sensor was activated and decoded, but does not match the protocol for the Make
Model Year that the tool was set-up for.
Failed Sensor Read
No Sensor Activation or Decode. May be wrong sensor fitment or non-functioning sensor. Tool
will prompt you to attempt reading the sensor 3 times.
Duplicate ID
A sensor with a duplicate ID has been read. The tool will direct you to re-read those sensors.
No Pressure
Sensor IDS read from ECU.
Low Battery

Tech 500 User Guide rev1.0 JUNE 2013
14
Sensor’s internal battery has dropped below a certain voltage threshold.
TEST BEFORE YOU TOUCH
TPMS is a process. With that Bartec has integrated that process to the tool. The 1st step with
TPMS is to conduct a Test Before You Touch. (Note: operator can skip TBYT and go directly to
RELEARN although not recommended). Test Before You Touch will prompt you through getting
a status of the vehicle prior to service by verifying the sensors are working and when
supported, verify the Diagnostic Trouble Codes (DTC).
To verify year, use 10th digit of the VIN.
Vehicle Operations Screen
Select by Make
Buick
Cadillac
Chevrolet
Chrysler
Dodge
7/45
Chevrolet
Corvette
Corvette C5
Corvette C6
Corvette Z06
Cruze
9/29
Chevrolet Cruze
2011
2012
1/2
ID:8920758D TEMP: 85
Mode: Learn BAT: Norm
32
32
32
32
Diagnosis:
Sensor Failure Detected
View data or print audit
report for details
Press any key to continue
Home
Test Before You Touch
Relearn
Review Data
Toolkit
My Tool
1/5

Tech 500 User Guide rev1.0 JUNE 2013
15
If equipped, tool will prompt user to connect to OBD and retrieve Diagnostic Trouble Codes
The Tech500 has the ability to Read out vehicle DTCs (Diagnostic Trouble Codes). Once read,
you will need to reference these codes with an external reference to determine the codes
definition.

Tech 500 User Guide rev1.0 JUNE 2013
16
RELEARN
Stationary Relearns
Active (Drive) Relearns
OBD Relearns
Stationary Relearns:
Stationary Relearns use the vehicles on-board TPMS system to listen for transmissions from
TPM sensors while the vehicle is in a “Learn Mode”. This is usually achieved through a series of
functions on the vehicle to place the vehicle into this mode.
Once the vehicle is in Learn Mode, using your Tech500 to activate the sensors, the vehicle will
listen for the sensor IDS and learn them to the vehicle.
Using your Tech500 to perform Stationary Relearns:
Home
Test Before You Touch
Relearn
Review Data
Toolkit
My Tool
1/5
Select by Make
Buick
Cadillac
Chevrolet
Chrysler
Dodge
7/45
Chevrolet
Corvette
Corvette C5
Corvette C6
Corvette Z06
Cruze
9/29
Chevrolet Cruze
2011
2012
1/2

Tech 500 User Guide rev1.0 JUNE 2013
17
>Inflate tires to Placard
>Capture all 4 ID’s
>Turn ignition to ON
>Plug OBDII Cable and select
>Write ID’s to Vehicle
>Leave vehicle in the ON position
>Start vehicle and ensure light is off
To verify year, use 10th digit of the VIN.
Follow on-screen instructions
Vehicle Operations Screen
Active (Drive) Relearns:
Active or Drive Relearns
Some vehicles can be reset by driving. Refer to the on-screen re-learn procedures for details on
how far/long to drive.
ID:8920758D TEMP: 85
Mode: Learn BAT: Norm
32
32
32
32

Tech 500 User Guide rev1.0 JUNE 2013
18
OBD Relearns:
Connection to a vehicle allows the Tech500 to directly program the vehicle electronics module
with TPM ID’s.
Note that not all vehicles support vehicle communications modes.
Once 4 TPM ID’s are stored within the Tech500, it can be connected to the OBD interface using
the provided cable.
Vehicle Operations Screen
Home
Test Before You Touch
Relearn
Review Data
Toolkit
My Tool
1/5
Select by Make
Buick
Cadillac
Chevrolet
Chrysler
Dodge
7/45
Chevrolet
Corvette
Corvette C5
Corvette C6
Corvette Z06
Cruze
9/29
Chevrolet Cruze
2011
2012
1/2
ID:8920758D TEMP: 85
Mode: Learn BAT: Norm
32
32
32
32

Tech 500 User Guide rev1.0 JUNE 2013
19
Follow on-screen instructions
During vehicle communication, the BACK key is inhibited. Should the process be commenced
inadvertently, the tool can be left to timeout on its own accord - approximately 20 seconds.
Once the communication is complete, the tool will flash IDS Written Successfully.
IF an Error Message comes up during the COMS process, Refer to Appendix F for COMS error
trouble shooting.
Indirect system –Vehicle may require calibration at point of service or replacement. No wheel
sensors on this type of TPMS.
Home
Test Before You Touch
Relearn
Review Data
Toolkit
My Tool
1/5
Select by Make
Buick
Cadillac
Chevrolet
Chrysler
Dodge
7/45
Chevrolet
Corvette
Corvette C5
Corvette C6
Corvette Z06
Cruze
9/29
Chevrolet Cruze
2011
2012
1/2
Connect tool to OBD II Port
and Turn Ignition ON
Press Enter to Read
Vehicle TPMS related info.
Press ESC to Cancel

Tech 500 User Guide rev1.0 JUNE 2013
20
>Inflate tires to Placard
>Capture all 4 ID’s
>Turn ignition to ON
>Plug OBDII Cable and select
>Write ID’s to Vehicle
>Leave vehicle in the ON position
>Start vehicle and ensure light is off
To verify year, use 10th digit of the VIN.
Follow on-screen instructions
Viewing Full Relearn Procedures