Bartec MAK TIGER 3003 User manual

BARTEC BENKE GmbH Schulstrasse 30 D-94239 Gotteszell Tel. [phone] Fax [phone]
E-mail: gottes[email protected] Internet: www.bartec.de
MAK 3003
Measuring system TIGER / LYNX
Operating Instructions
Software MAK 3003 2.35
BA 190130

All rights reserved. Subject to change without prior notice.
No part of this document may be reproduced, processed or distributed
in any form or by any means without the prior written permission of BARTEC
BENKE.
Copyright © 2022 by
BARTEC BENKE
Schulstraße 30
D-94239 Gotteszell

Contents
1
MAK 3003 Measuring system TIGER / LYNX Operating Instructions, Software version 2.35, BA 190130 (11.07.2022)
Table of Contents
1About this manual...........................................................................................................................5
2Safety Precautions..........................................................................................................................6
3Basics 7
3.1 Compact Controller.......................................................................................................7
3.1.1 Keypad..........................................................................................................................7
3.1.2 Display..........................................................................................................................7
3.2 Operating Concept........................................................................................................8
3.2.1 The software user interface..........................................................................................8
3.2.2 Info line .........................................................................................................................8
3.2.3 Softkeys........................................................................................................................8
3.2.4 Hidden softkeys ............................................................................................................9
3.2.5 Event display...............................................................................................................10
4Overview of functions...................................................................................................................11
5Tour start and tour end.................................................................................................................13
5.1 Switching on the system.............................................................................................13
5.2 Manual tour start.........................................................................................................13
5.3 Ending the tour............................................................................................................14
6Enter supplier number..................................................................................................................15
6.1 Manual input ...............................................................................................................15
6.2 Supplier recording with GPS.......................................................................................16
7Milk intake......................................................................................................................................18
8Sampling ........................................................................................................................................20
8.1 Single sample .............................................................................................................21
8.2 Tour sample................................................................................................................22
8.3 Belgium sample ..........................................................................................................23
8.3.1 Procedure ...................................................................................................................23
8.3.2 Belgium Sample menu................................................................................................26
8.3.2.1 Sampler errors............................................................................................................27
8.3.2.2 Additional Analysis of Tank.........................................................................................28
8.3.2.3 Additional Sample.......................................................................................................29
8.3.2.4 Manual sample............................................................................................................31
8.4 SMV4 sample..............................................................................................................32
8.4.1 Procedure ...................................................................................................................32
8.4.2 Additional sample .......................................................................................................36
9Tank segment monitoring ............................................................................................................39
10 Raw milk separation......................................................................................................................42
11 Data transfer to the office.............................................................................................................49
12 Tour menu......................................................................................................................................50
12.1 Intake..........................................................................................................................51
12.2 Pump over measured .................................................................................................51
12.3 Pump over segment....................................................................................................53
12.4 Drain the measuring system.......................................................................................57
12.5 Pump over unmeasured .............................................................................................58
12.6 Manual cleaning..........................................................................................................60
12.7 Automatic cleaning .....................................................................................................62

Contents
2
MAK 3003 Measuring system TIGER / LYNX Operating Instructions, Software version 2.35, BA 190130 (11.07.2022)
12.8 Activate pre-sample....................................................................................................63
12.9 Pre-sample switched off.............................................................................................63
12.10 Long-term memory.....................................................................................................64
12.11 Unloading unmeasured..............................................................................................65
12.12 Driver number input....................................................................................................66
12.13 Tank segment levels ..................................................................................................66
12.14 Tank segment quality.................................................................................................67
13 Shortcut keys................................................................................................................................68
13.1 Intake data of the last supplier ...................................................................................68
13.2 Tank segment levels ..................................................................................................68
14 Main Menu .....................................................................................................................................69
14.1 Data transfer...............................................................................................................70
14.2 Long-term memory.....................................................................................................70
14.3 Password level...........................................................................................................73
14.4 Databases..................................................................................................................75
14.5 Configuration..............................................................................................................76
14.6 Service menu .............................................................................................................77
14.6.1 Logfile Browser...........................................................................................................77
14.6.2 Activate Bluetooth ......................................................................................................78
14.7 Language ...................................................................................................................80
14.8 Cleaning.....................................................................................................................81
14.9 Special functions HLW...............................................................................................82
14.9.1 Pump over..................................................................................................................82
14.9.2 Cleaning .....................................................................................................................83
14.9.3 Emptying system........................................................................................................83

Contents
3
MAK 3003 Measuring system TIGER / LYNX Operating Instructions, Software version 2.35, BA 190130 (11.07.2022)
Warranty
Our “Terms & Conditions of Sale and Delivery” shall apply as a general
principle.
These shall be available to the operator upon entering into the contract
at the latest.
Claims may not be brought under the warranty or for liability in case of
personal injury and property damage where attributable to one or more
of the following root causes:
►Improper use of the product.
►Incorrect assembly, commissioning, operation and mainte-
nance of the product.
►Failure to follow the instructions in the manual regarding
transport, storage, assembly, commissioning, operation and
maintenance.
►Unauthorised structural alterations to the product.
►Inadequate monitoring and inspection of parts which are sub-
ject to wear.
►Incorrectly executed repairs.
►Disasters caused by foreign objects and extraneous forces be-
yond all control.
►No liability shall be accepted for consequential damage as a
general rule.
EU-Declaration of conformity
We BARTEC BENKE GmbH, Schulstraße 30, D-94239 Gotteszell,
hereby declare, that this product is in compliance with the essential re-
quirements of the relevant EU-directives.
The EU-Declaration of conformity for this product can be obtained from
BARTEC BENKE GmbH, Schulstraße 30, D-94239 Gotteszell,
[email protected].

Contents
4
MAK 3003 Measuring system TIGER / LYNX Operating Instructions, Software version 2.35, BA 190130 (11.07.2022)

About this manual
5
MAK 3003 Measuring system TIGER / LYNX Operating Instructions, Software version 2.35, BA 190130 (11.07.2022)
1 About this manual
The operating instructions are part of the product and must be kept in the
immediate vicinity of the device. The personnel for assembly, operation and
maintenance must have access to it at all times.
The operating instructions contain important notes, safety instructions and test
certificates that are necessary for the correct functioning of the device during
operation. The operating instructions are intended for all persons involved in
the assembly, installation, commissioning and maintenance of the product.
The illustrations in this manual are intended to illustrate the information and
descriptions. They cannot always be transferred unchanged and may differ
slightly from the actual design of the device.
BARTEC GmbH reserves the right to make technical changes at any time.
BARTEC GmbH is under no circumstances responsible or liable for any indi-
rect or consequential damages resulting from the use, operation or application
of this user manual.
Please read the operating instructions carefully before using the
product.
Please note that the instructions must be kept by the user for the entire
life of the product.
Signs and symbols
The following characters and symbols are used in this manual to highlight
passages that need special attention.
Notes
This arrow indicates special features to be observed during operation.
Warning
This symbol draws your attention to passages that, if not followed or followed
inaccurately, may result in damage to or destruction of parts of the system or
loss of data.
Danger!
This symbol marks passages that, if not followed, endanger the health or life
of humans.
Special notes that appear within the text are marked with a frame.

Safety Precautions
6
MAK 3003 Measuring system TIGER / LYNX Operating Instructions, Software version 2.35, BA 190130 (11.07.2022)
2 Safety Precautions
The system operator is responsible for all complying with all regulations appli-
cable to the storage, transport and handling of the food product "milk".
All regulations and provisions remain in full force when operating the system
with MAK devices.
MAK devices are built in compliance with applicable regulations and must
leave the factory in perfect condition. The devices must be installed and ser-
viced by qualified technicians.
Make sure that the information and operating conditions listed by the man-
ufacturer are followed.
Follow the instructions on operating and servicing the devices.
If you notice any damage or deterioration on parts of the system or if safe
operation is not ensured for other reasons, do not start up the system or
shut it off immediately. Notify your service point.
You should also contact our service technicians if you notify malfunctions
or defects during operation or have any doubts as to whether the devices
are working property.
The measuring system may only be operated for applications that are subject
to legal metrological control in the respective EU member state if the nominal
operating conditions specified in the EU-type examination certificate are met.
The controller software is constantly evolving. A different software version or
configuration may cause the screen displays on your system to differ slightly
from the illustrations in this document.

Basics
7
MAK 3003 Measuring system TIGER / LYNX Operating Instructions, Software version 2.35, BA 190130 (11.07.2022)
3 Basics
With the MAK 3003 system, all processes and operating steps required for the
loading and unloading of milk collection and transport vehicles can be rec-
orded and controlled.
The TIGER 3003 version is used to control milk intake and record the data
entered during that process.
The system is operated from the compact controller.
Switching on the system and operating the vehicle system depend on the spe-
cific vehicle type and the operating instructions applicable thereto.
3.1 Compact Controller
The compact controller is the main control and information unit for the whole
system. Communication between the controller and other components in a
system is handled via USB or, for P-NET devices, via P-NET.
3.1.1 Keypad
The system is operated using the touch-sensitive keys on the control unit
(touch screen) (number keys, selector keys, soft keys and operating keys) and
using the key functions which appear the display depending on the situation.
The functions of the soft keys are controlled by the software based on the
current operating status.
3.1.2 Display
A graphic display screen which is designed as a touch screen is used to show
all readouts. Thanks to the backlit transreflective liquid crystal technology
used, the display can be easily read even in darkness or bright sunlight.
Softkeys
Display
Number Keys
Operating Keys
Selector Keys

Basics
8
MAK 3003 Measuring system TIGER / LYNX Operating Instructions, Software version 2.35, BA 190130 (11.07.2022)
3.2 Operating Concept
3.2.1 The software user interface
After starting the system, the main screen appears on the display.
You can call up different screens or operating modes using the soft keys to
the left and right of the display.
Corresponding to the installed measuring equipment type (TIGER, LYNX
HLW, ABO Magyar, V3003, Optimate, ROMEX, V plus or E-TIGER) differ the
start screen and the main menu.
3.2.2 Info line
The info line shows the date and time, information about the operating status
and the software page number.
3.2.3 Softkeys
The softkeys can be assigned various functions, the current meaning of which
is indicated by symbols.
All keys are touch-sensitive, meaning that you don’t need to press them but
simply have to touch them.
Bringing up the menu
Info line
Displaying softkey assignments
Time
Date
Password level
Page
Fault

Basics
9
MAK 3003 Measuring system TIGER / LYNX Operating Instructions, Software version 2.35, BA 190130 (11.07.2022)
3.2.4 Hidden softkeys
In various operating situations, the current assignment of soft keys is not
shown on the display. In such instances, the keys to the left or right of the
display will not be marked. In this case, you have to touch any soft key in this
row of keys. The current assignment of the soft keys will be shown for three
seconds. During this time, you can touch one of the soft keys to start the func-
tion in question.
Call up event screen
Show data from the last tour

Basics
10
MAK 3003 Measuring system TIGER / LYNX Operating Instructions, Software version 2.35, BA 190130 (11.07.2022)
3.2.5 Event display
Important error or malfunction messages are shown right on the display.
The event screen is called up using the hidden softkey EVENTS . This displays
all operating statuses and malfunctions.
To exit the event screen, touch the same softkey again.

Overview of functions
11
MAK 3003 Measuring system TIGER / LYNX Operating Instructions, Software version 2.35, BA 190130 (11.07.2022)
4 Overview of functions
The operating sequence and scope during the round of sampling depend on
the respective equipment and the configuration of the software.
All functions that are available during and outside of a tour are described be-
low.
The actual operating sequence results from the differing combinations of the
individual functions. The following illustrations may therefore deviate from the
displays.
Tour start and tour end
A tour must be started in order to be able to perform intake or discharge pro-
cesses. For the tours, default data may be available that contain all the nec-
essary information.
The tour can also be started without default data. All data must be entered
manually (chapter 5).
Enter supplier number
The data of all intake or discharge processes are recorded and can be
uniquely assigned to each supplier. For this reason, a supplier number must
be entered before each process. The numbers can be recorded in different
ways (chapter 6).
Milk intake
The actual milk intake at the supplier takes place when all the necessary data
have been entered and recorded (chapter 7).
Sampling
Samples can be taken from the collected milk in different ways and filled
(chapter 8).
Tank segment monitoring
The filling level of the tank segments and the filling sequence can be moni-
tored and displayed (chapter 9).
Raw milk separation
During intake, the milk can be filled into separate tank segments according to
its quality. Qualities from 1 (good) to 8 (bad) are possible (chapter 10)
Data transfer
The recorded data are transferred via an Internet connection using the config-
ured FTP server (see chapter 11).

Overview of functions
12
MAK 3003 Measuring system TIGER / LYNX Operating Instructions, Software version 2.35, BA 190130 (11.07.2022)
Special functions in the tour
During the tour, various functions are available via the tour menu (e.g., acti-
vation or deactivation of functions, discharge and transfer processes, clean-
ing) (chapter 12).
Shortcut keys
During the tour, you can call up various displays directly using one-touch keys
(chapter 13).
Functions outside the tour
Various control and service functions can be called up in the main menu
(chapter 14).

Tour start and tour end
13
MAK 3003 Measuring system TIGER / LYNX Operating Instructions, Software version 2.35, BA 190130 (11.07.2022)
5 Tour start and tour end
5.1 Switching on the system
Switch on the system according to the installation on the vehicle (usually a
separate switch).
When the system is switched on, the controller executes a start-up program.
The start screen is then shown on the display.
5.2 Manual tour start
With the described software version, the tour is started only manually.
●Touch the soft key START TOUR .
●In the following window, enter the details for the current tour or check the
details and change them if necessary.
Entering of the driver number depends on the configuration. If input is re-
quested, it can be done manually or by tag reader.
The entered data are stored in the database and displayed again the next time
the tour starts.

Tour start and tour end
14
MAK 3003 Measuring system TIGER / LYNX Operating Instructions, Software version 2.35, BA 190130 (11.07.2022)
5.3 Ending the tour
●To end the current tour, touch the soft key END TOUR .
●Then enter the number of the destination dairy and the current mileage.
●Confirm the entries with the soft key CONFIRM ; the "Tour log record" is
printed.

Enter supplier number
15
MAK 3003 Measuring system TIGER / LYNX Operating Instructions, Software version 2.35, BA 190130 (11.07.2022)
6 Enter supplier number
To perform an intake, a supplier number must be entered.
6.1 Manual input
●Touch the soft key INTAKE .
The window for entering the intake data opens.
●If the "Supplier ID" line is selected, touch the soft key CHANGE or enter
the number directly using the numeric keys.
The window for entering the supplier number opens. Enter the supplier
number there.
You can use the BACK SPACE soft key to delete the character to the left of
the cursor.
●Confirm the number.

Enter supplier number
16
MAK 3003 Measuring system TIGER / LYNX Operating Instructions, Software version 2.35, BA 190130 (11.07.2022)
6.2 Supplier recording with GPS
If the vehicle stops at a position within a tour for which supplier data are stored
in the database, these data are automatically displayed.
The requirement for this is that an intake has already been carried out at this
location with the corresponding supplier number. The supplier number must
be manually input once (see section 6.1). It is then automatically saved and
assigned to the location.
Supplier selection
If several suppliers are stored under one location, you can use the selection
keys on the controller to select a supplier.
1 supplier
found
2 suppliers
found

Enter supplier number
17
MAK 3003 Measuring system TIGER / LYNX Operating Instructions, Software version 2.35, BA 190130 (11.07.2022)
New supplier
If the intake is not to take place at any of the suppliers displayed, and instead
a new supplier is to be entered under the current position, you must first enter
this supplier manually.
●Touch one of the soft keys to the right of the display to display the hidden
softkeys.
●Then touch the INTAKE soft key.
●Enter the supplier number (see section 6.1).

Milk intake
18
MAK 3003 Measuring system TIGER / LYNX Operating Instructions, Software version 2.35, BA 190130 (11.07.2022)
7 Milk intake
After confirming the manually entered supplier number, or after displaying a
supplier number from the database, you can start the intake.
●Touch the START button on the controller or press the start button on the
remote control.
The milk intake starts and the measured data are shown on the display.