Bartec Agile X IS User manual

10,1" Industry tablet PC 17-A1B.-.... /........
User Manual

GmbH
Max-Eyth-Straße 16
Tel: [phone]
Support:
[e-mail]
97980 Bad Mergentheim,
Germany
Fax: [phone]
Download:
http://automation.bartec.de
GERMANY
Internet:
www bartec de
User Manual - Translation
Industry Tablet PC 10.1"
Agile X IS
Type 17-A1B*-****/********
ATEX / IECEx Zone 0
ATEX / IECEx Zone 1
UL Class I Division 1
UL Class I Zone 0
UL Class I Zone 1
Document No.: 11-A1B0-7D0001 / 406842
Status: 30 May 2017
Reservation:
Technical data subject to change without notice. Changes, errors
and misprints may not be used as a basis for any claim for damages.
Content Pages
English 1-43

Contents 10.1" Tablet PC - Agile X IS
Type 17-A1B*-1***/********
Subject to technical changes.
05/2017
1. Basic safety information................................................................................................................. 1
1.1 Information on this user manual ........................................................................................................ 1
1.1.1 Languages ......................................................................................................................................... 2
1.1.2 Changes in the document ................................................................................................................. 2
1.1.3 Registered trademarks ...................................................................................................................... 2
1.2 Handling the product ......................................................................................................................... 2
1.3 Intended use ...................................................................................................................................... 3
1.3.1 Exclusive purpose ............................................................................................................................. 3
1.3.2 Unintended use ................................................................................................................................. 3
1.4 Duties of the operator ........................................................................................................................ 3
1.5 Safety information ............................................................................................................................. 3
1.5.1 General .............................................................................................................................................. 3
1.6 General safety information for operation ........................................................................................... 4
1.6.1 Maintenance ...................................................................................................................................... 4
1.6.2 Servicing ............................................................................................................................................ 4
1.6.3 Inspection .......................................................................................................................................... 4
1.6.4 Repairs .............................................................................................................................................. 4
1.6.5 Commissioning .................................................................................................................................. 4
1.7 Labelling, test certificate and standards ............................................................................................ 4
1.8 Warranty ............................................................................................................................................ 4
1.9 Co-applicable documents - set of documents ................................................................................... 5
1.10 Definition of terms ............................................................................................................................. 6
1.11 Configuration ..................................................................................................................................... 6
2. Product description ........................................................................................................................ 7
2.1Agile X IS ........................................................................................................................................... 7
2.2 Structure ............................................................................................................................................ 7
2.2.1 Front side .......................................................................................................................................... 7
2.2.2 Rear side ........................................................................................................................................... 8
2.2.3 Side view ........................................................................................................................................... 9
2.3 Purpose of use .................................................................................................................................. 9
3. Explosion protection and approvals...........................................................................................10
3.1 Applicable standards ....................................................................................................................... 10
4. Technical data ............................................................................................................................... 11
4.1 Features .......................................................................................................................................... 11
4.1.1 Performance features ...................................................................................................................... 11
4.1.2 Physical characteristics ................................................................................................................... 11
4.1.3 Ambient conditions .......................................................................................................................... 12
4.1.4 Application development ................................................................................................................. 12
4.1.5 Data transmission WiFi ................................................................................................................... 13
4.1.6 Data transmission Bluetooth............................................................................................................ 13
4.1.7 Data transmission LTE .................................................................................................................... 13
4.1.8 1D/2D Imager (SE4500-SR) ............................................................................................................ 14
4.1.9 Decode range .................................................................................................................................. 15
4.1.10 Symbologies supported ................................................................................................................... 15
4.1.11 RFID reader HF/NFC ...................................................................................................................... 16
4.2 Internal and external battery ............................................................................................................ 17
4.3 External interfaces ........................................................................................................................... 17
4.4 Product labelling .............................................................................................................................. 18
5. Transport and storage.................................................................................................................. 19
5.1 Transport ......................................................................................................................................... 19
5.2 Storage ............................................................................................................................................ 19

Industry Tablet PC 10.1" Agile X IS
Type 17-A1B*-****/******** Contents
Subject to technical changes.
05/2017
6. Commissioning............................................................................................................................. 20
6.1 Scope of delivery ............................................................................................................................. 20
6.1.1 Optional accessories ....................................................................................................................... 20
6.2 Requirements in potentially explosive atmosphere ......................................................................... 21
6.3 First steps ........................................................................................................................................ 21
6.3.1 Inserting external battery/cover module .......................................................................................... 22
6.3.2 Charge internal and external battery ............................................................................................... 23
6.3.3 Battery LED status .......................................................................................................................... 24
6.3.4 Turn on/Turn off the Agile X IS ........................................................................................................ 24
6.3.5 Key combination .............................................................................................................................. 25
6.4 Windows operating system – Getting started .................................................................................. 26
6.4.1 Windows 10 IoT Enterprise ............................................................................................................. 26
6.4.2 Windows Embedded 8.1 Industry Pro ............................................................................................. 27
6.5 Activating peripheral equipment ...................................................................................................... 27
6.6 Insert MicroSD card, Micro SIM card or USB stick .......................................................................... 28
6.6.1 Insert USB stick ............................................................................................................................... 28
6.6.2 Insert Micro SIM card (only functions with an optional LTE module available) ................................ 28
6.6.3 Insert MicroSD card ......................................................................................................................... 29
6.6.4 Remove/replace screen protector ................................................................................................... 29
6.7 Add on module ................................................................................................................................ 29
7. Operation....................................................................................................................................... 30
7.1 Final inspection ............................................................................................................................... 30
7.2 Cleaning .......................................................................................................................................... 30
7.3 Operation, recommendations and requirements ............................................................................. 31
7.3.1Basic safety and health protection requirements ............................................................................. 31
7.3.2 Information on the use of wireless devices ...................................................................................... 31
7.3.3 Safety in aircraft .............................................................................................................................. 31
7.3.4 Safety in hospitals ........................................................................................................................... 31
7.3.5 Heart pacemakers ........................................................................................................................... 31
7.3.6 Hearing aids .................................................................................................................................... 31
7.3.7 Other medical equipment ................................................................................................................ 31
7.3.8 Equipping laser devices .................................................................................................................. 32
7.3.9 LED units ......................................................................................................................................... 32
7.3.10 Restrictions in the case of wireless devices .................................................................................... 32
7.4 Operating frequency - FCC and IC .................................................................................................. 33
7.5 Electromagnetic fields ..................................................................................................................... 35
8. Faults and troubleshooting.......................................................................................................... 36
8.1 Troubleshooting ............................................................................................................................... 36
8.2 Resetting the Tablet PC using the recovery function ...................................................................... 37
9. Service, inspection and repair..................................................................................................... 39
9.1 Service intervals .............................................................................................................................. 39
9.2 Inspection ........................................................................................................................................ 39
9.3 Service and repair work ................................................................................................................... 39
9.3.1 Information on sending in for repairs ............................................................................................... 39
10. Disposal......................................................................................................................................... 40
11. Shipping and packaging information.......................................................................................... 40
12. Accessories................................................................................................................................... 41
13. Additional information.................................................................................................................. 41
13.1 Links ................................................................................................................................................ 41
14. EU Declaration of Conformity...................................................................................................... 42

Blank page

Industry Tablet PC 10.1" Agile X IS
Type 17-A1B*-****/******** Basic safety information
Subject to technical changes.
05/2017 EN 1/43
1. Basic safety information
1.1 Information on this user manual
Read carefully before putting the devices into operation.
The user manual is a fixed part of the product. It must be kept in the direct vicinity of the
device and the installation, operating and service staff must have access to it at all
times.
The user manual contains important information, safety instructions and test certificates
which are necessary for the perfect function of the device in operation.
The user manual is directed at all individuals concerned with the commissioning,
handling and servicing of the product. The applicable guidelines and standards for
areas with gas and dust atmosphere (EN/IEC 60079-17, EN/IEC 60079-
19,) must be
observed when conducting this work.
Knowledge of the safety and warning information in this user manual and the strict
compliance with it is essential for safe installation and commissioning
. Accidents,
injuries and material damage can be avoided by circumspect handling and
systematically following the instructions.
The examples, tables, and figures provided in this user manual are for illustration
purposes. Due to the different requirements of the respective application, the BARTEC
company cannot assume responsibility or liability for actual use based on the examples
and figures.
The BARTEC company reserves the right to carry out technical changes at any time.
In no event will BARTEC company be responsible or liable for indirect or consequential
damages resulting from the use or application of this user manual.
Safety instructions and warnings are specially highlighted in these operating instructions
and marked by symbols.
DANGER
DANGER
describes a directly imminent danger. If not avoided, death or severe injury
will be the consequence.
WARNING
WARNING
describes a possibly imminent danger. If not avoided, death or severe injury
may be the consequence.
CAUTION
CAUTION
describes a possibly imminent danger. If not avoided, mild or slight injury
may be the consequence.

Basic safety information Industry Tablet PC 10.1" Agile X IS
Type 17-A1B*-****/********
EN 2/43 Subject to technical changes.
05/2017
ATTENTION
ATTENTION describes a possibly damaging situation. If not avoided, the plant or
objects in its vicinity may be damaged.
Important information on effective, economical & environmentally compliant
handling.
1.1.1 Languages
The original user manual with safety information is written in English. All other available
languages are translations of the original user manual.
The user manual is available in English. If further languages are required, these must
be requested from BARTEC or stated on placing an order.
1.1.2 Changes in the document
BARTEC reserves the right to change the content of this document without notification.
No warranty is assumed for the correctness of the information. In cases of doubt, the
German safety instructions apply because it is not possible to rule out errors of
translation or printing. In the case of legal disputes, the “General Terms and Conditions
of Business” of the BARTEC GmbH also apply.
The current versions of the datasheets, operating instructions, certificates and EC
declarations of conformity can be downloaded from www.bartec.de
or may be
requested directly from BARTEC GmbH.
1.1.3 Registered trademarks
Intel® is a registered trademark of Intel Corporation
Centrino® is a registered trademark of Centrino Mobile Technology
Bluetooth® is a registered trademark of Bluetooth Special Interest Group
WINDOWS is a registered trademark of MICROSOFT Corporation
1.2 Handling the product
The product described in this user manual left the factory in a perfect and tested state
in terms of safety. To maintain this state and to achieve a perfect and safe operation of
this product, it may only be operated in the manner described by the manufacturer. In
addition, the perfect and safe operation of this product requires correct transportation,
proper storage and careful operation.
The safe and perfect handling of the tablet PC is a prerequisite for its perfect and
correct functioning.

Industry Tablet PC 10.1" Agile X IS
Type 17-A1B*-****/******** Basic safety information
Subject to technical changes.
05/2017 EN 3/43
1.3 Intended use
1.3.1 Exclusive purpose
The tablet PC Agile X IS is a handheld piece of electrical equipment. It serves the
purpose of the mobile recording, processing and/or radio transmission of data within
potentially explosive atmospheres.
It is used exclusively in combination with devices which comply with the requirements
placed on the overvoltage category I.
The admissible operating data of the device used must be considered.
1.3.2 Unintended use
Any other use is unintended and may lead to damage and accidents. The manufacturer
shall not be liable for any use extending beyond the exclusive purpose.
1.4 Duties of the operator
The operator undertakes to only permit persons to work with the tablet PC who:
-are acquainted with the basic regulations on safety and accident prevention, and
who have been inducted in the use of the tablet PC,
-have read and understood the documentation, the safety chapter and the
warnings.
The operator checks that the safety and accident prevention regulations applicable to
the respective case of use have been observed.
1.5 Safety information
1.5.1 General
–Do not attempt to open the devices.
–Do not charge batteries in potentially explosive atmospheres.
–General statutory provisions or guidelines on occupational
health and safety,
accident prevention provisions and environmental protection laws must be
heeded, e.g. Operational Safety Ordinance (BetrSichV) and nationally applicable
ordinances.
–
Use suitable clothing and shoes with respect to the danger of hazardous
electrostatic charges.
–Avoid heat influences outside the specified temperature range.
–
Protect device from external influences! Do not expose device to
caustic/aggressive liquids, vapours or spray. In the case of malfunction or
damaged enclosure, remove the device immediately from the potentially explosive
atmosphere and bring it to a safe place.

Basic safety information Industry Tablet PC 10.1" Agile X IS
Type 17-A1B*-****/********
EN 4/43 Subject to technical changes.
05/2017
1.6 General safety information for operation
1.6.1 Maintenance
The pertinent erection and operating provisions for electrical systems must be
observed! (E.g. Directive
RL 2014/34/EU, BetrSichV and nationally applicable
ordinances EN 60079-14, IEC 60079-14 and the series DIN VDE 0100)!
Observe the national waste disposal regulations when disposing of materials.
1.6.2 Servicing
No constant servicing will be necessary if operated correctly under consideration of the
assembly instructions and environmental conditions. See Chapter “Service, inspection,
repair” in this respect.
1.6.3 Inspection
According to EN/IEC 60079-17 and EN/IEC 60079-
19, the operator of electrical
systems in potentially explosive atmospheres is obliged to have these inspected by an
electrician to ensure correct condition.
1.6.4 Repairs
Repairs to explosion-proof equipment may only be performed by persons authorized by
BARTEC, who must employ the latest technolog
ical practices, observe the
manufacturer's instructions and use only original spare parts. The applicable
regulations are to be observed here.
1.6.5 Commissioning
It must be checked that all components and documents are available before
commissioning.
1.7 Labelling, test certificate and standards
The device features an explosion protection label, as well as a test certificate. For an
explanation of the symbols and information used, see chapter 4 "Technical data".
The Tablet PC series complies with Directive 2014/34/EU on equipment and protective
systems intended for use in potentially explosive atmospheres (ATEX Directive). For
information on standards that must be observed, see chapter 3 "Explosion protection
and approvals".
1.8 Warranty
WARNING
Explosion protection cannot be guaranteed if non-specified components are
used.
Do not make any changes or perform any reconstruction work on the device.
Use only original spare parts.

Industry Tablet PC 10.1" Agile X IS
Type 17-A1B*-****/******** Basic safety information
Subject to technical changes.
05/2017 EN 5/43
The manufacturer provides a full warranty exclusively for
the spare parts it
supplies. When using parts from third parties, there is no guarantee that they
have been designed or manufactured to handle the requisite stress or offer the
requisite degree of safety.
Our “General Terms and Conditions of Sale and Delivery” shall apply in principle.
These shall be made available to the operator on signing of contract at the latest.
Warranty and liability claims in the case of injury and damage to property shall be
excluded if they are attributable to one or several of the following causes:
–Unintended use of the tablet PC.
–Incorrect handling
–Failure to observe the information in the user manual with respect to transport,
storage, commissioning, operation and service.
–Independent structural changes
–Faulty monitoring of parts subject to wear and tear.
–Incorrectly performed repairs.
–Cases of disaster through the impact of foreign bodies and force majeure.
BARTEC grants a warranty period of three years on the Tablet PCs (exception: internal
and external rechargeable battery ½ year), starting from the BARTEC delivery date.
The warranty period for accessories is 1 year from the date of delivery. This warranty
covers all parts of the delivery and is limited to the free-of-charge replacement of or
repair of the defective parts by BARTEC. The packaging supplied should ideally be
retained for this purpose (return shipping). If necessary and following written
consultation, the products should be sent to us with an RMA form. No claims may be
submitted for repair work to be performed at the installation location.
The information contained in this document refers to the explosion-proof version of the
Agile X IS Tablet PC series.
This user manual contains all important information on the topic of explosion protection.
A quick guide and further product information on handling and commissioning are also
available.
1.9 Co-applicable documents - set of documents
−User manual for the tablet PC series Agile X IS
Describes the usage, commissioning and the settings of the explosion-proof
version of the Agile X IS Tablet PC series.
−Quick Start Guide for the tablet PC series Agile X IS
Describes safety-relevant information, first use and provides further data on the
explosion-proof version of the Agile X IS Tablet PC series.
The software and manual are available for download at: http://automation.bartec.de

Basic safety information Industry Tablet PC 10.1" Agile X IS
Type 17-A1B*-****/********
EN 6/43 Subject to technical changes.
05/2017
1.10 Definition of terms
A few abbreviations are used in the documentation.
IS = Intrinsically Safety is used a generic term for the
Zone 0, Zone 1 and Division 1 version
= Stands for the entire explosion-proof product range
1.11 Configuration
The devices are only supplied with preinstalled operating system
–Windows 10 IoT Enterprise CBB – 64 Bit
–Windows Embedded 8.1 Industry Professional – 64 Bit
Customer software or further applications are not contained in the delivery.
Configuration
Version
Processor
Intel Pentium N3710 Quad Core 1.6 GHz
Display
10.1”
Resolution
1920 x 1200 pixel
System memory 8 GB SODIMM DDR3L-1600
Mass memory 128 GB SATA uSSD
Operating
system options
Supplied as standard with
-Windows 10 IoT Enterprise Professional – 64 Bit
-Windows Embedded 8.1 Industry Professional – 64 Bit
WLAN
IEEE 802.11 a/b/g/n/ac
Bluetooth
Version 4.1 LE Class I
WWAN
(optional) -4G/LTE module with European frequencies
-4G/LTE module with North American frequencies
GPS u-Blox Neo-M8N
Scanner
(optional) SE 4500 1D/2D Imager from Zebra Technologies Corporation
RFID-Reader
HF/NFC
13.56 MHz
ISO 15693 (read and write)
ISO 14443-A (read and write)
ISO 14443-B (only read UID)

Industry Tablet PC 10.1" Agile X IS
Type 17-A1B*-****/******** Product description
Subject to technical changes.
05/2017 EN 7/43
2. Product description
2.1 Agile X IS
The
Agile X IS
is a rugged Tablet PC with 10.1" display which has been designed for
use in industrial environments and was developed specifically by BARTEC for use in
potentially explosive atmospheres.
2.2 Structure
2.2.1 Front side
NoDescription
1 Full HD 10-finger multi-touch outdoor display
2 2x digital microphone inclusive noise cancellation
3 Rubber bumper
4 Front camera
5 Brightness sensor
6 Kensington lock
7 LED indicators
8 Power button
9 Home menu button
10 Function key, freely programmable

Product description Industry Tablet PC 10.1" Agile X IS
Type 17-A1B*-****/********
EN 8/43 Subject to technical changes.
05/2017
2.2.2 Rear side
NoDescription
11 I/O ports USB 2.0 port
MicroSD card slot
Micro SIM card slot
Charging port
12 Volume (+/-)
13 Function key
14 Expansion port for add on modules
15 High quality 5MP camera with flash
16 SE4500 1D/2D Imager from Zebra Technologies Corporation (optional)
17 Multi-stage battery compartment locking mechanism
18 Empty module/external battery (can be changed during active operations)
for battery compartment
19 Docking station connection

Industry Tablet PC 10.1" Agile X IS
Type 17-A1B*-****/******** Product description
Subject to technical changes.
05/2017 EN 9/43
2.2.3 Side view
NoDescription
20 Charging port
21
Micro SIM card slot
22 MicroSD card slot
23 USB 2.0 port
2.3 Purpose of use
The tablet PCs Agile X IS is a handheld electrical device. They serve the purpose of
entry, processing and (radio) transmission of data within potentially explosive
atmospheres.
The tablet PC Agile X IS is used exclusively in combination with devices which comply
with the requirements placed on the overvoltage category I.
The tablet PC Agile X IS is developed for the use in the following potentially explosive
atmospheres:
−ATEX / IECEx Zone 0
−ATEX / IECEx Zone 1
−UL Class I Division 1 Groups A, B, C and D
−UL Class 1 Zone 0 AEx ia IIC T4 Ga
−UL Class 1 Zone 1 AEx ia IIC T4 Gb
The tablet PC Agile X IS may not be used in the following zones:
−ATEX / IECEx Zone 20, 21 and 22
−UL Class II Division 1 und Division 2
−UL Class III

Explosion protection and
approvals Industry Tablet PC 10.1" Agile X IS Type 17-A1B*-****/********
EN 10/43 Subject to technical changes.
05/2017
3. Explosion protection and approvals
ATEX
ATEX Zone 0 Typ: 17-A1B5-****/********
17-A1B6-****/******** II 1 G Ex ia op is IIC T4 Ga -20 °C ≤ Ta ≤ +50 °C
ATEX Zone 1 Typ: 17-A1B3-****/********
17-A1B4-****/******** II 2 G Ex ia op is IIC T4 Gb -20 °C ≤ Ta ≤ +50 °C
Test certificate DEMKO 16 ATEX 1803
Standards EN 60079-0:2012 + A11: 2013
EN 60079-11: 2012 EN 60079-28: 2015
Guidelines ATEX 2014/34/EU EMV 2014/30/EU
R&TTE 1999/5/EC RoHS 2011/65/EU
IECEx
IECEx Zone 0 Typ: 17-A1B5-****/********
17-A1B6-****/******** Ex ia IIC op is T4 Ga -20 °C ≤ Ta ≤ +50 °C
IECEx Zone 1 Typ: 17-A1B3-****/********
17-A1B4-****/******** Ex ia IIC op is T4 Gb -20 °C ≤ Ta ≤ +50 °C
Test certificate IECEx UL 16.0160
Standards IEC 60079-0: 2011 IEC 60079-11: 2011
IEC 60079-28: 2014
Guidelines ATEX 2014/34/EU EMV 2014/30/EU
R&TTE 1999/5/EC RoHS 2011/65/EU
UL Class I, Division 1 and Class I Zone 0 / 1
UL Class I
Division 1 Typ: 17-A1B1-****/******** 17-A1B4-****/********
17-A1B6-****/********
Class I, Division 1,
Groups A, B, C and D
UL Class I
Zone 0 Typ: 17-A1B6-****/******** Class I, Division 1, Groups A, B, C and D Class I, Zone 0, AEx ia IIC T4 Ga
-20 °C ≤ Ta ≤ +50 °C
UL Class I
Zone 1 Typ: 17-A1B4-****/******** Class I, Division 1, Groups A, B, C and D Class I, Zone 1, AEx ia IIC T4 Gb
-20 °C ≤ Ta ≤ +50 °C
Test certificate for USA and Canada IECEx UL 16.0160
Standards UL 913: 8th Edition UL 60079-0: 6th Edition
UL 60079-11: 6th Edition
CAN/CSA C22.2 No. 157-92
CAN/CSA C22.2 No. 6079-0:11
CAN/CSA C22.2 No. 6079-11:11
3.1 Applicable standards
See the chapter entitled "EU Certificate of Conformity"

Industry Tablet PC 10.1" Agile X IS
Type 17-A1B*-****/******** Technical data
Subject to technical changes.
05/2017 EN 11/43
4. Technical data
4.1 Features
4.1.1 Performance features
Processor Intel Pentium N3710 Quad Core 1.6 GHz
1.6 – 2.56 GHz clock speed
Operating system Windows 10 IoT Enterprise CBB - 64 Bit
Windows Embedded 8.1 Industry Pro - 64 Bit
System memory 8 GB SODIMM DDR3L-1600
Mass memory 128 GB SATA uSSD
Expansion slot MicroSD card slot supports
up to 32 GB
Interfaces
Tablet-PC
1 x USB 2.0 port
1 x MicroSD card slot
1 x Micro SIM card slot
1 x Charging port (DC 19 V)
1 x Extension port for Add-on module
1 x Port docking station
Interfaces
Docking station 4 x USB 2.0 1 x RS232 serial
1 x Ethernet 10/100 Mbit/s
1 x HDMI
1 x Charging port (DC 9 V to 36 V)
4.1.2 Physical characteristics
Dimensions
(width x height x depth) 290 mm x 209 mm x 33 mm
Weight
(including internal battery)
Depends on version and configuration
approx. 2,3 kg
Display Size 10.1"
Background lighting LED
Luminance 700 cd/m2 (typical)
Contrast 800:1 (typical)
Touch Projective capacity Multi-Touch 10 points
Size 10.1"
Interactive sensor technology Light sensor
G Sensor
E-compass

Technical data Industry Tablet PC 10.1" Agile X IS
Type 17-A1B*-****/********
EN 12/43 Subject to technical changes.
05/2017
Keys on front side Keys on rear side
-1x programmable function button
(Fn1)
-1x home / menu button
-1x power button
-
1 x programmable function button
(Fn2); (if no 1D/2D-Imager)
-2 x button for volume ( +/-)
4.1.3 Ambient conditions
Operating temperature
In potentially explosive atmosphere -20 °C to +50 °C / -4 °F to +122 °F
Operating temperature
during charging 0 °C to +40 °C / +32 °F to +104 °F
Storage temperature -20 °C to +50 °C / -4 °F to +140 °F
Air humidity 5 % to 95 % (non-condensing)
Class of protection (EN/IEC 60529) IP 65 (Industry)
4.1.4 Application development
Creating a customer-specific image
All drivers for creating a dedicated image are available on the BARTEC download
page.
1D/2D imager
The Zebra SE4500-SR Imager is the 1D/2D Imager. The Zebra Scanner SDK contains
a package of components that forms a uniform framework for software development
and offers a large number of functions for communication between Zebra scanners and
user-specific applications and solutions.
HF/NFC RFID reader
An SDK for integration in customer-specific applications is available.
The software and SDK are available for download at: http://automation.bartec.de.

Industry Tablet PC 10.1" Agile X IS
Type 17-A1B*-****/******** Technical data
Subject to technical changes.
05/2017 EN 13/43
4.1.5 Data transmission WiFi
Radio standard IEEE 802.11 a/b/g/n/ac
Antenna reference 0-2 dBi peak gain
WiFi (2,4 GHz) RF Specification
Frequency range 2,400 GHz ~ 2,497 GHz (2,4 GHz ISM Band)
WiFi (5 GHz) RF Specification
Frequency range 4,900 GHz ~ 5,845 GHz (5,0 GHz ISM Band)
4.1.6 Data transmission Bluetooth
Bluetooth Specification
Bluetooth-Standard Bluetooth V4.1 von 1, 2 und 3 Mbit/s
Antenna reference 0~2 dBi peak gain
Frequency band 2402 MHz – 2480 MHz
4.1.7 Data transmission LTE
Module support is not provided for all required bands. In terms of LTE support, only data
is supported (no speech function). Video calls can be supported via other apps such as
Skype or Line. For connectivity, the WWAN module supports the following bands:
4.1.7.1 PLS8-E (Europa)
Frequency band
GSM/GPRS/EGDE
UMTS/HSPA+:
LTE:
Dual band: 900/1800 MHz
Triple band: 900 (Bd 8)/1800 (Bd 3)/2100 MHz (Bd 1)
Bands: 800 (Bd 20)/900 (Bd 8)/1800 (Bd 3)/
2600 MHz (Bd 7)
4.1.7.2 PLS8-X-US
Frequency band
GSM/GPRS/EGDE
UMTS/HSPA+:
LTE:
Quad band 850 MHz/900 MHz/1800 MHz/1900 MHz
Triple band: 850 (Bd 5)/AWS (Bd 4)/1900 MHz (Bd 2)
Bands: 700 (Bd 17) 850 (Bd 5)/AWS (Bd 4)/
1900 MHz (Bd 2)

Technical data Industry Tablet PC 10.1" Agile X IS
Type 17-A1B*-****/********
EN 14/43 Subject to technical changes.
05/2017
4.1.8 1D/2D Imager (SE4500-SR)
For Agile X IS with integrated 1D/2D Imager
The SE4500-SR is ideal for small to medium-sized 1D/2D barcodes.
The maximum scanning range of the 1D/2D Imager depends on the barcode
type, print quality, module width (in mm) and software setting.
Laser class CDRH/IEC Class 2 laser and IEC Class
1M light
Aiming LED (VLD) 655 Nm ± 10 nm
Decode
range
5 mil Code 39
100 % UPC/EAN
6.7 mil PDF 417 Decode range
Skew, pitch & roll Skew tolerance : ± 60° Pitch tolerance : ± 60°
Roll tolerance : 360°
Focal distance from front of engine approx. 20 cm / 8.0 inch
Scan rate up to 60 fps
Sensor resolution 752 (H) x 480 (V) pixel
Field of view
Horizontal: 40 deg.
Vertical : 25 deg.
Illumination element 2 x 625nm LEDs
Minimum print contrast
Minimum 25% absolute dark/light
reflectance measured at 650 nm
Insensitivity to ambient light 96,900 Lux