silverlynx CARRERA BED User manual

Bomi Furniture P/L trading as SilverLynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au
CARRERA BED
Assembly Instructions
Please retain these instructions for future reference
Please read through these assembly instructions carefully to ensure that you can assemble your new purchase
without stress. These detailed instructions will guide you on how to prepare and assemble your bedroom suite.
DIFFICULTY
WE ADVISE YOU DO NOT USE POWERED DRILLS TO ASSEMBLE ANY BOLTS ON THIS
EQUIPMENT PROVIDED
NOT PROVIDED: Flat Head Screwdriver
Thank you for purchasing a SilverLynx product
As one of Australia’s leading bedroom furniture manufacturers, we have long established partnerships with
Australia’s most successful retailers.
Customers who buy our products recognise our commitment to quality and customer satisfaction.
SilverLynx is a values-based business. Our commitment to quality, evolving design leadership, customer
service and exceeding customer expectations - is unsurpassed in the industry.
Enjoy your SilverLynx bed.
Hardware Pack: containing –4x (M6) 10mm button head bolts; 2x 38mm screws; 1x allen key
There are additional bolts and hardware that are pre-installed to your components as required.
*NOTE: The hardware pack may contain more items than required. Please contact our sales team if you have any
questions/concerns.
Slat System: See the attached document “Amendment to instructions for all SilverLynx beds”.
Bed Frame Parts:

Bomi Furniture P/L trading as SilverLynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au
STEP 1 –Position Bed Head and Side
Rails approximately where your bed is to
be set up. Remove 4x bolts from the
sides of your Bed Head using a flat head
screwdriver (not provided) to keep the
slot on the cross dowel horizontal (this
keeps the thread for the bolt straight so
that it can be un-wound easily).
STEP 2 –Move one Siderail into
place and re-attach bolt to the Bed
Head panel through the holes in the
Siderail panel. Use the screwdriver to
keep the cross dowel aligned with the
bolt so that it catches easily by hand
(do NOT force bolts if you feel
resistance –adjust cross dowel
alignment).
STEP 3 –Complete the above
process on the other Side Rail.
STEP 1
STEP 2 & 3
STEP 2 & 3

Bomi Furniture P/L trading as SilverLynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au
STEP 4 –Next, connect the top of your
Side Rails to the top of the Bed Head
panel. Remove the black M8 16mm
bolts from the back of the Side Rail
capping and loosen the bolts holding the
fixing plates onto the back of the Bed
Head panel –enough so the plates can
be rotated (you may need to remove the
bolts securing the fixing plate near the
leg in order to rotate it).
STEP 5 –Turn the top plate 90
degrees so that the free hole aligns with
the bolt hole on the Side Rail capping.
Secure the plates using the black M8
16mm bolts you removed in step 4
(finger tight only). Repeat this process
with the bottom plate, then repeat on the
other Side Rail. Tighten all bolts using
the allen key. Once snug, tighten only
with ¼ turn of the Allen Key. DO NOT
USE powered drills as over-tightening
can damage bolts.
STEP 6 –Remove the two button
head bolts for the Floating Bar from the
foot end of each Siderail. Gently lift the
Siderails and position the Floating Bar,
lining up the holes on each end of the
Floating Bar with the holes on the side
rails
STEP 7 –Using the bolts you
removed from the Siderails, secure
(finger tight only) the Floating Bar in
place.
STEP 8 –Lift the Bed Foot into place,
hooking the Side Rail brackets onto the
foot brackets. Screw two button head
bolts (M4) into the position shown
below and tighten (finger tight only).
Note you may have more bolts than
you need.
Having trouble? See *Helpful Tips* at
the end of this document.
STEP 4 & 5
STEP 7
STEP 6
STEP 8

Bomi Furniture P/L trading as SilverLynx ABN 99 006 489 541 11-17 Sages Road Glenroy Victoria 3046 Australia
T:[phone] F:[phone] E:[e-mail] W:www.silverlynx.com.au
STEP 9 –Ensure that the bed is
sitting square and then tighten all bolts
using the allen key. Once snug, tighten
only with ¼ turn of the Allen Key. DO
NOT USE powered drills as over-
tightening can cause foot end rail to
bow. Your bed should now look like the
following diagram.
STEP 10 –To set up the slat and
spine system, proceed to the
instructions titles “Amendment to
instructions for all SilverLynx beds”.
Note the 2x 38mm screws provided in
the hardware pack can be used in this
section of the assembly.
NOTES
•Button head bolts should be regularly inspected and may need to be retightened periodically
•Never drag or move assembled bed as this may damage the bed
CARE & MAINTENANCE
Your SilverLynx product is crafted with care, properly maintained, it will mature over time developing a rich
deep patina enhancing its appearance. To get the best performance from your SilverLynx product, please
follow the simple care instructions listed below.
•Do not use silicone based polishes/cleaners at any time.
•Dust surfaces gently with a feather duster then wipe gently with a slightly damp cloth/chamois.
•Do not allow liquids, damp clothes to remain in contact with lacquered surface for extended periods.
•Never place furniture in close proximity to heating outlets.
•Exposure to direct sunlight will cause colour fading to fabrics, leathers and timber finishes.
•Do not allow solvents, abrasives or heated objects to come in contact with the suite.
•Do not use cordless drivers or power drills to tighten your bed brackets, as over-tightening can cause the
foot end rail to bow.
Contact your retailer or our sales office for further information
*Helpful Tips*
STEP 8 –If you are having trouble connecting the button head bolts on the foot bracket, try shifting the foot end
slightly up &/or down as this can help line up the holes so the bolts can connect easily.
GENERAL
Do not tighten bolts before attaching all components and making sure they sit square. When ready,
make sure bolts are snug, then tighten only with ¼ turn of the Allen Key. DO NOT USE powered drills as
over-tightening can cause components to bow.
Never force bolts if you can feel resistance as this can cause the thread to strip. Try to adjust the hole alignment
until your bolt can connect easily by hand.
STEP 9