Home Styles 88 5003 181 User manual

Home Styles Consumer Assistance : www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Hardware List
Part List
IMPORTANT NOTE.
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure
a completed product as it was designed.
For assembly see instructions in carton 88 5003 182
88 5003 181
Executive Desk
B.
Back Panel
1 pc.
A.
Top
1 pc.
E.
Middle Panel
1 pc.
F.
Middle Panel
1 pc.
Cam Lock
24 pcs. (+6 extra)
Cam Lock Screw
24 pcs. (+2 extra)
M4x25
Machine Screw
10 pcs.
Knob
10 pcs.
M3x25
Wood Screw (long)
56 pcs. (+1 extra)
M3x15
Wood Screw (short)
24 pcs. (+1 extra)
M3x10
Wood Screw
for Hinge
6 pcs. (+1 extra)
M6x32
Wood Screw
for Base
8 pcs. (+1 extra)
Flat Washer
8 pcs. (+1 extra)

Home Styles Consumer Assistance : www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
Part List
IMPORTANT NOTE.
Carefully remove all the parts from the carton and put
them individually on a soft cloth to prevent scratches
or other damage occurring to the parts.
We have taken great care in the design of this
product and request that you carefully and strictly
follow our assembly instructions to ensure
a completed product as it was designed.
Tools required for assembly : Phillips screwdriver, Level
For assembly also need carton 88 5003 181
88 5003 182
Executive Desk
(Please refer to the last page of these
instructions for drawer assembly steps.)
N.
Keyboard Front
1 pc.
O.
Keyboard
1 pc.
P.
Metal Strip
4 pcs.
I.
Base
1 pc.
J.
Base
1 pc.
H.
Front Stretcher
2 pcs.
C.
Side Panel
1 pc.
D.
Side Panel
1 pc.
K .
Drawer
2 pcs.
M.
Drawer
2 pcs.
L.
Drawer
2 pcs.
G.
Front Stretcher
1 pc.

Assembly Instructions 2/7
IMPORTANT
* Please keep Hex Wrench in a safe place as you may need to tighten up the Head Cap Bolts in the future.
* Do not tighten up all the bolts until each part is properly assembled.
* Use a soft cloth between these parts and the floor.
* After assembly, item must be level to work properly. Use the included adjustable levelers to level.
STEP 1
Insert Cam Lock Screws into pre-drilled
holes of Top (A), Back Panel (B),
Side Panels (C) and (D) and
Middle Panels (E) and (F).
(See Figure 1)
Cam Lock Screw
A
B
Figure 1
Cam Lock Screw
F
E
C
D
Cam Lock Screw

Assembly Instructions 3/7
STEP 4
Attach Bases (I) and (J) to unit
with Flat Washers and
Wood Screws for Base.
(See Figure 3)
Figure 3
STEP 3
Attach Front Stretchers (G) and
(H) to unit with Cam Locks.
Attach Side Panels (C) and (D)
to unit with Cam Locks.
STEP 2
Attach Middle Panels (E) and (F) to
Back Panel (B) with Cam Locks.
(See Figure 2)
Cam Lock
B
F
E
G
C
DCam Lock
H
H
JI
Wood Screw
for Base
Flat Washer
Figure 2

Assembly Instructions 4/7
STEP 5
Attach Keyboard Front (N) to Keyboard (O) with
Wood Screws for Hinge.
Attach Knobs to keyboard with Machine Screws.
(See Figure 4)
Figure 4
Figure 6
STEP 6
Turn the unit from Step 4
over to its’ upright position.
Attach Top (A) to unit with Cam Locks.
Slide keyboard into position.
N
O
Figure 5
STEP 5
Slide Drawers (K), (L) and (M)
into position.
If you want to remove Drawer (M)
in the future, push the plastic
level on its’ left side up,
push the plastic level on its’
right side down and
pull open slowly.
(See Figure 5)
To level the unit, adjust the
adjustable levelers on the
bottom of unit.
(See Figure 6)
Note : Unit must be level to work properly.
Wood Screw for Hinge
Cam Lock
A
K
L
M
K
M
L

Part List
Drawer K
K1.
Drawer Front
2 pcs.
K2.
Drawer Back
2 pcs.
K3.
Drawer Side
2 pcs.
K4.
Drawer Side
2 pcs.
K5.
Drawer Base
2 pcs.
STEP 1
Attach 1, K2 and K3 using aKPhillips
screwdriver and wood screws (4X),long
tighten halfway.
Attach K1, K2 and K4 using a Phillips
screwdriver and wood screws (4X),long
tighten halfway. (See Figure 1)
Figure 2
K1
K3
K4
K5
STEP 2
Slide K5 into groove of K3 and K4. Be sure
to push K5 all the way forward so it meets K1.
(See Figure 2)
STEP 3
Insert wood screw (4X) into pre-drilledshort
holes of K5, tighten screws. (See Figure 3)
Figure 3
STEP 4
Attach Pull Handle with Machine Screws.
(See Figure 4)
Figure 4
Tighten all screws used in drawer assembly.
Assembly Instructions 5/7
K1
K2
K3
K4
Figure 1
MAKE SURE ROLLER
IS ON THE BACK
K5

Part List
L1
Drawer L
L2
L3
L4
Figure 1
STEP 1
Attach 1, L2 and L3 using aLPhillips
screwdriver and wood screws (4X),long
tighten halfway.
Attach L1, L2 and L4 using a Phillips
screwdriver and wood screws (4X),long
tighten halfway. (See Figure 1)
MAKE SURE ROLLER
IS ON THE BACK
Figure 2
L1
L3
L4
K5
STEP 2
Slide K5 into groove of L3 and L4. Be sure
to push K5 all the way forward so it meets L1.
(See Figure 2)
K5
Figure 3
STEP 4
Attach Pull Handle with Machine Screws.
(See Figure 4)
Figure 4
Tighten all screws used in drawer assembly.
L1.
Drawer Front
2 pcs.
L2.
Drawer Back
2 pcs.
K5.
Drawer Base
2 pcs.
L3.
Drawer Side
2 pcs.
L4.
Drawer Side
2 pcs.
Assembly Instructions 6/7
STEP 3
Insert wood screw (4X) into pre-drilledshort
holes of K5, tighten screws. (See Figure 3)

Part List
M1.
Drawer Front
2 pcs.
M2.
Drawer Back
2 pcs.
K5.
Drawer Base
2 pcs.
M3.
Drawer Side
2 pcs.
M4.
Drawer Side
2 pcs.
Drawer M
STEP 1
Attach 1, M2 and M3 using aMPhillips
screwdriver and wood screws (6X),long
tighten halfway.
Attach M1, M2 and M4 using a Phillips
screwdriver and wood screws (6X),long
tighten halfway. (See Figure 1)
Figure 2
STEP 2
Slide K5 into groove of M3 and M4. Be sure
to push K5 all the way forward so it meets M1. (See Figure 2)
STEP 4
Attach Pull Handle with
Machine Screws.
(See Figure 4)
Figure 4
Tighten all screws used
in drawer assembly.
Assembly Instructions 7/7
Legal Size
Letter Size
Figure 5
Figure 4
STEP 3
Insert wood screw intoshort (4X)
pre-drilled holes of K5, tighten screws.
(See Figure 3)
K5
Figure 3
M1
M3
M4
K5
M1
M2
M3
M4
Figure 1
STEP 5
Place Metal Strips (P)
into position.
(See Figure 5)
The Metal Strip (P)
can be adjusted for
letter or legal size files
as shown.
P