Home Styles Monarch Kitchen Island 88 5020 941 User manual

Hardware List
Part List
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319
88 5020 941
Kitchen Island
IMPORTANT
Cam Lock
15 pcs. (+2 extra)
Cam Lock Screw
15 pcs. (+1 extra)
1/2”
Round Head Screw
4 pcs. (+1 extra)
3/4”
Round Head Screw
8 pcs. (+1 extra)
1”
Round Head Screw
16 pcs. (+1 extra)
M6x35
Head Cap Bolt
20 pcs. (+1 extra)
Magnet
2 pcs.
M4x25
Machine Screw
4 pcs.
Knob
4 pcs.
Flat Washer
8 pcs. (+1 extra)
3/4”
Flat Head Screw
12 pcs. (+1 extra)
Adjustable Pin
16 pcs. (+1 extra)
Patent 8,584,600 B2
Carefully remove all the parts from the carton and
place them individually on a soft cloth to prevent
scratches or other damage.
Carefully and strictly follow these assembly instructions
to ensure a completed product as designed.
Do not use power tools above 8 volts to assemble.
B.
Side Panel
1 Pc.
C.
Side Panel
1 Pc.
D.
Middle Panel
1 Pc.
K.
Back Panel
2 Pcs.
L.
Back Piece
1 Pc.
E.
Front Rail
1 Pc.
F.
Front Rail
1 Pc.
G.
Back Rail
1 Pc.
H.
Back Rail
1 Pc.
I.
Shelf
4 Pcs.
M.
Door
1 Pc.
N.
Door
1 Pc.
J.
Bottom
1 Pc.
O.
Drawer
2 Pcs.
Refer to the last page(s) of these
instructions for drawer assembly.
Small Hex Wrench
1 pc.
Hex Wrench
1 pc.
Cartons 88 5020 942, 88 5008 943 or 88 5009 943 are also needed for assembly.
Tool(s) required for assembly: LevelPhillips screwdriver,

Assembly Instructions 2/8
IMPORTANT
Use a soft cloth between these parts and the floor.
Do not use power tools above 8 volts to assemble.
Do not tighten all the bolts until each part is properly assembled.
The unit must be level to work properly. Use the included adjustable levelers to level.
Keep Hex Wrench in a safe place as the bolts may need to be tightened up in the future.
STEP 1
Insert Cam Lock Screws into the
pre-drilled holes of Side Panels (B), (C),
Front Rails (E), (F), Back Rails (G), (H),
Bottom (J) and Back Piece (L).
(See Figure 1)
STEP 2
Attach Magnets to Front Rail (F)
with 1/2” Round Head Screws. (See Figure 2)
Figure 1
G
L
H
J
B
C
F
E
Cam Lock Screw
1/2” Round Head Screw
Magnet
Figure 2
F

Assembly Instructions 3/8
E
F
D
G
K
K
L
H
B
C
Cam Lock
Cam Lock
STEP 3
Attach Middle Panel (D) to Front Rails (E), (F),
Back Rails (G), (H) and Back Piece (L) with Cam Locks.
(See Figure 3)
Slide Back Panels (K) into place.
STEP 4
Attach Side Panels (B) and (C)
to unit with Cam Locks.
Figure 3

Figure 4
Assembly Instructions 4/8
STEP 5
Attach Bottom (J) to unit with Cam Locks,
Head Cap Bolts and Flat Washers.
Tighten bolts using Hex Wrench.
(See Figure 4)
STEP 6
Attach Frame Legs (P) and (Q)
to unit with Head Cap Bolts.
Tighten bolts using Hex Wrench.
J
Cam Lock
Head Cap Bolt
Head Cap Bolt
Flat Washer
P
Q

Assembly Instructions 5/8
1” Round Head Screw
STEP 9
Attach Knobs with Machine Screws.
Drawer (O)
STEP 7
Attach Drawer Front (O1) and Drawer
Back (O2) to Drawer Side (O3) with
1” Round Head Screws.
STEP 8
Slide Drawer Bottom (O5) into the grooves
of Drawer Front (O1) and Drawer Back (O2)
until it meets Drawer Side (O3).
Attach Drawer Side (O4) to unit with
1” Round Head Screws.
Part List
O1.
Drawer Front
2 pcs.
O2.
Drawer Back
2 pcs.
O3.
Drawer Side
2 pcs.
O4.
Drawer Side
2 pcs.
O5.
Drawer Bottom
2 pcs.
Roller at back
O2
O2
O4
O5
O1
O3
O3
O1

Assembly Instructions 6/8
STEP 10
Attach Doors (M) and (N) to unit,
by sliding the door lift hinges
into the side panel lift hinges.
(See Figure 5)
Assemble Knobs to Doors (M)
and (N) with Machine Screws.
(See Figure 6)
Level the unit by adjusting the
adjustable levelers on the bottom
of unit. (See Figure 7)
Insert 3/4” Round Head Screws
into the pre-drilled holes in the
back panel.
Note : Please make sure unit is level
before tightening these screws.
STEP 11
Slide Drawers (O) into place.
Insert Adjustable Pins into side
panels and middle panel at the
desired level.
Slide Shelves (I) into position.
3/4” Round Head Screw
Machine Screw
Adjustable Pin
Knob
3/4” Round Head Screw
M
N
Figure 5 Figure 6
Figure 7
I
I
O
O

Assembly Instructions 7/8
STEP 13
Pull out the Drawers from unit.
Attach Top (A) to the unit with
Head Cap Bolts and Flat Washers.
Tighten bolts using Hex Wrench.
(See Figure 8)
Slide Drawer into place.
STEP 12
Place Top (A1) and Top (A2)
upside down on a soft cloth.
Attach Top (A1) to Top (A2) using
3/4” Flat Head Screws.
A1
A2
3/4” Flat Head Screw
Flat Washer
Head Cap Bolt
Figure 8

Assembly Instructions 8/8
STEP 14
When Leaf Top is down, it should be oriented vertically.
If it is not vertical and adjustment is desired, turn the
adjuster on the adjuster block on back rail.
(See Figure 9)
STEP 15
Lift up the Leaf Top.
STEP 16
Holding the Leaf Top up, pull out a back leg
from the unit; then pull out the other leg.
Adjuster Black
Adjuster Black
Figure 9
TOP EXTENSION INSTRUCTIONS

NEVER
use glass cleaners on
finished furniture. Ammonia
chemically attacks the finish.
allow liquids to remain on furniture.
Absorption causes parts to warp
and split and finishes to delaminate.
NEVER
CARE INSTRUCTIONS
Do not use rubber
based placemats.
PREVENT
DISCOLORING
Do not use commercial
waxes and polishes.
PREVENT
YELLOWING
Do not place hot
objects on surface.
PREVENT
FINISH DAMAGE
Do not write
directly on surface.
PREVENT
MARKING
Do not use power tools
above 8 volts to assemble.
PREVENT
CRACKING
Do not place
in direct sunlight.
PREVENT
FADING
with a soft cloth moistened
in lukewarm soap and water.
Buff with a dry clean cloth.
CLEAN
Home Styles will provide replacements free of charge for missing or damaged hardware or parts within 30 days of
purchase. Digital images of the defective parts may be required. If the product was not purchased from an authorized
retail affiliate, Home Styles is under no obligation to provide replacement parts. Parts are not available for fully assembled
items nor are parts available for sale. Replacements for missing or damaged hardware or parts may be requested at:
www.homestyles-furniture.com/customer-service/replacement-parts
Home Styles Customer Service: www.homestyles-furniture.com,
[email protected], 888-680-7460, 877-831-0319