PB TEEN Stuff Your Stuff Desk User manual

www.pbteen.com
Stuff Your Stuff Desk
PRE-ASSEMBLY:
•Please read all instructions before beginning assembly.
•Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or
hardware.
PARTS INCLUDED:
A - Desk Top – 1 pc B - Leg – 4 pcs
C - Breadboard – 1 pc D - Drawer – 1 pc
HARDWARE INCLUDED:
E - Flat Washer – 8 pcs F - Lock Washer – 8 pcs G - Nut – 8 pcs
H - Allen Wrench – 1 pc I - Stopper – 2 pcs
ASSEMBLY INSTRUCTIONS:
1. Lay the Desk Top (A) upside down on a soft surface or scratch-free surface.
2. Attach the Legs (B) by inserting the exposed threads into the pre-drilled holes on the corner blocks.
Secure with Flat Washers (E), Lock Washers (F) and Nuts (G) using Allen Wrench (H). See Figure 1.
3. Insert the Breadboard (C) into the Desk Top (A) with the insert nut on the breadboard facing up, as shown
in Figure 1. Insert and tighten Stoppers (I) into the insert nut on the Breadboard.
4. Turn the desk right-side up. Attach the Drawer (D) to the Desk Top (A) by inserting the Drawer’s (D) glide,
which is pre-mounted on two sides of the Drawer (D), into the runner, which is pre-assembled on the Desk
Top (A). Push the Drawer (D) in until the lock stick of the glide on the Drawer (D) stays inside the runner
on the Desk Top (A). See Figure 2.
Note: To detach the Drawer (D) from the Desk Top (A). Pull the drawer until it‘s stopped by the lock stick.
Press down on the lock stick on the right side and lift up the left side of the Drawer (D), then pull out to
remove it. See figure 2.

www.pbteen.com
Figure 1
Stopper (I)
Inserted Nut
on the bottom of Breadboard (C)
GF
I
I
CB
A
E
Figure 2
Glide
which is pre-mounted
on the Drawer
Runner
which is pre-assembled
on the Desk Top
Lock Stick
on the Glide
CARE INSTRUCTIONS:
•Dust often with a soft, dry cloth.
•To clean, slightly moisten cloth with water (a damp cloth will hold dust and prevent scratching; dry
thoroughly).

www.pbteen.com
Stuff-Your-Stuff Tower – Top
PARTS INCLUDED:
A- Tower Top (1pc)
B- Large Shelf Panel (2pcs)
C- Small Shelf Panel (1pc)
HARDWARE INCLUDED:
D- Wood Screw (M 3.5 x 5/8”) (8pcs)
E- Mending Plate (2-15/16” x 13/16” x 1/16”) (2pcs)
F- Shelf Support Wire (9-5/8” x 11/16” x 1/8”) (6pcs)
TOOLS REQUIRED (but not included):
•Phillips Head Screwdriver
•Drill needed for Tipping Restraint
ASSEMBLY INSTRUCTIONS:
1. Insert Shelf Support Wires (F) into pre-drilled holes in the middle of both Large Shelf Panels (B).
2. Insert Shelf Support Wires (F) into pre-drilled holes in the underside of the top shelf and on the top of
bottom shelf of the Tower Top (A). See Figure 1.
3. Attach both Large Shelf Panels (B) by sliding them onto the Shelf Support Wires (F) on Tower Top (A).
4. Attach Small Shelf Panel (C) by sliding it onto the Large Shelf Panel’s (B) Shelf Support Wires (F).
5. Carefully place the Tower Top Unit (A) onto the Tower Base Unit.
6. Secure Tower Top Unit (A) to Tower Base Unit by using Mending Plates (E). Place the Mending Plates (E)
over the pre-drilled holes located in the rear of the Tower Top (A) and Tower Base Unit. Secure with Wood
Screws (D). See Figure 2
Figure 1
C
A
A
D
E
CARE INSTRUCTIONS:
•Dust often using a soft, dry cloth.
•To protect the finish, do not apply abrasives or household cleaners.
Figure 2

www.pbteen.com
Furniture Tipping Restraint
Young children may be injured by tipping furniture. The use of a tipping restraint is highly recommended.
When properly installed, this restraint could provide protection against the unexpected tipping of furniture due
to small tremors, bumping or climbing. We recommend mounting this restraint to a wall stud.
WARNING: This product is only a deterrent. It is not a substitute for proper adult supervision.
Hardware Included:
A - (2) Brackets B - (2) Long screws
C - (2) Short screws D - (1) Nylon strap
Installation Instructions:
1. Locate a wall stud behind your furniture. Position a Bracket (A) on the stud approximately 1” below the top of the
furniture. Mark and drill pilot hole into the center of the stud with a 3/32” drill bit.Attach a
Bracket (A) to the stud with the Long Screws (B) provided.
2. On the back of the furniture, the second Bracket (A) will need to be attached to the furniture frame at
the top. To do this, temporarily move the furniture into its final position and mark the location of the
wall’s Bracket (A) on the furniture frame with a pencil.
3. Move the furniture away from the wall and place a Bracket (A) on the mark. Using the marks from the
previous step as a guide, drill holes for screws with a 3/32” drill bit. Attach the bracket to the furniture
with the Short Screws (C) provided.
4. Move the furniture into its final position, taking care to line up the wall bracket with the furniture
bracket. Thread the Nylon Strap (D) through the Bracket as shown in the illustration. Tighten strap until snug. Do
not over tighten.

www.pbteen.com
Stuff-Your-Stuff Tower - Base
PARTS INCLUDED:
A- Tower Base (1pc)
B- Shelf (1pc)
HARDWARE INCLUDED:
C- Shelf Pin (4pcs)
ASSEMBLY INSTRUCTIONS:
1. Insert the 4 Shelf Pins (C) into pre-drilled holes located on the interior walls of the Tower Base (A), at the
desired height position.
2. Place Shelf (B) onto the Shelf Pins (C), making sure the Shelf (B) is stable.
A
B
C
CARE INSTRUCTIONS:
•Dust often using a soft, dry cloth.
•To protect the finish, do not apply abrasives or household cleaners.