Spectrum Industries 37118 User manual

Note: The core table should be fully-assembled in it’s nal location
before proceeding with this installation. These end worksurfaces
should be installed before the side worksurfaces or center console
panel. If you have existing side worksurfaces and a center console
panel installed, they will need to be removed.
0115715 Page 1 of 3
Assembly Instructions
Important
Before you begin, please make sure all parts and proper quantities
are included. Any parts damaged during shipment must be reported
within 15 days of receipt. To report information regarding damage, to
purchase parts or accessories, or if you have any questions, please
contact us at:
www.spectrumfurniture.com
715-723-6750, 800-235-1262
Thank you for purchasing Spectrum products!
End worksurface for InVision Access Table
37118 - Curved
37119 - Rectangular
(24) 026064
1/4-20 x 5/8” PHMS
(4) 0115718
cantilever worksurface
bracket
(2) 036281
dual unit-to-unit bracket
37118
curved worksurface
37119
rectangular worksurface
cantilever
worksurface
bracket
(4 required)
1. Install cantilever worksurface brackets
1. Make sure the table is upright. It may take 3-4 people to ip.
2. Tip the 4 cantilever end worksurface brackets while inserting
into the leg slots. Figure 1A.
The end worksurface brackets
have to be installed into the
slots before any worksurfaces
are installed. The end worksurfaces
will be installed rst, then the side
worksurfaces (step 3), then center
console panel.
Figure 1A
Phillips
screwdriver
Tools
Required
(1) worksurface
0115713 - curved worksurface
0115722 - rectangular worksurface

0115715 Page 2 of 3
Figure 1B
3. Set the end worksurface onto the brackets and align the mounting holes. Figure 1B.
4. Install two 1/4-20 x 5/8” PHM screws through each bracket to secure the end worksurface. Do not tighten completely.
5. Install one 1/4-20 x 5/8” PHM screw per bracket through the bracket and into the table leg. Do not tighten completely.
6. Install the two unit-to-unit brackets with (2) 1/4-20 x 5/8” PHM screws. Do not tighten completely.
Keep all installed fasteners
loose until step 3.
end worksurface
(curved shown)
unit-to-unit bracket with
(2) 1/4-20 x 5/8” PHMS
1/4-20 x 5/8”
PHMS
1/4-20 x 5/8”
PHMS
unit-to-unit bracket with
(2) 1/4-20 x 5/8” PHMS
2. Attach support plates to side worksurfaces
1. Place the side worksurfaces laminate-side down
onto a non-abrasive surface. Figure 2.
2. Attach a support plate to each worksurface with
(3) 1/4-20 x 5/8” PHM screws and tighten securely.
Figure 2
side worksurface
support plate
1/4-20 x 5/8” PHMS
(3 required)
Phillips
screwdriver
Tools
Required
Note: Steps 2-3 use parts included with the table.

0115715 Page 3 of 3
925 First Avenue, PO Box 400, Chippewa Falls, WI 54729 Ph: 800-235-1262, 715-723-6750 Fax: [phone]
E-mail: [email protected] web: www.spectrumfurniture.com
3. Install side worksurfaces
1. Set the 2 side worksurfaces onto the table and align the mounting holes. Figure 3A.
2. Attach each side worksurface to the table with (4) 1/4-20 x 2-3/4” PHM screws and tighten securely.
3. Install a 1/4-20 x 5/8” PHM screw through the remaining hole in each cantilever worksurface bracket and into
the side worksurface.
4. Attach each unit-to-unit bracket to the side worksurface with (2) 1/4-20 x 5/8” PHM screws. Figure 3B
5. Line up the edges of the previously installed end worksurfaces with the side worksurfaces.
6. When everything is aligned and without gaps, tighten all worksurface and unit-to-unit bracket screws securely.
7. The center console panel can now be installed.
Figure 3A
side worksurface
(install 2nd)
1/4-20 x 2-3/4” PHMS
(4 required per side worksurface)
Phillips
screwdriver
Tools
Required
side worksurface
(install 2nd)
end worksurface
(install 1st)
end worksurface
(install 1st)
1/4-20 x 2-3/4”
PHMS
dual unit-to-
unit bracket
Figure 3B