Baumr-ag Sh0910 User manual

Chainsaw Sharpener

User Manual

RETAIN THIS MANUAL FOR FUTURE REFERENCE

PLEASE READ THIS MANUAL CAREFULLY BEFORE USE

Chainsaw Sharpener

i

Table of Contents

PREFACE.................................................................................................................................................1

PARTS................................................................................................................................................... 2

SAFETY INFORMATION...................................................................................................................... 3

ELECTRICAL SAFETY......................................................................................................................... 5

ASSEMBLY........................................................................................................................................... 6

GRINDING .............................................................................................................................................. 9

Grinding depth Delimiter..........................................................................................................10

DIMENSIONS ........................................................................................................................................ 11

SPECIFICATIONS ................................................................................................................................14

Chainsaw Sharpener

Preface

Thanks for buying the Chainsaw Sharpener, another high-quality machine from our company. To

get the most out of your purchase, please read the manual before use.

We ask you to please read this manual carefully beforehand in order to familiarise yourself with

this product and after reading, please store this instructional manual for future reference. Failure

to follow the proper protocols listed in the manual may cause personal injury to the operator or

damage to equipment.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Sharpener

Parts

Position

Description

Position

Description

1

Hand Piece

8

Cutting Angle Setting Wheel

2

Grinding Disk Lateral Guard

9

Scale

3

Depth of Grind Set Screw

10

Mounting Screw (10a/10b)

4

Cutting Edge Angle Set-Up Wheel

11

Guide Plate

5

Base

12

Chain Stop

6

Guide Screw

13

Grinding Disk

7

Rotary Table

14

Grinding Disk Protective Enclosure

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Sharpener

Safety Information

Chainsaw sharpeners can be dangerous when used improperly. Please observe basic safety

precautions to eliminate risk of fire, electric shock and personal injuries.

Familiarise yourself with the sharpener before use.

Only use the sharpener for the application if which it is designed.

Mount the sharpener on a non-skid and level ground.

Ensure that you stand securely and maintain your balance at all times.

Be attentive and be careful of what you do. One moment of carelessness when using the

device can result in serious injuries.

Do not use the device when you are tired or under the influence of drugs or alcohol.

Wear suitable work clothes!

Do not wear loose-fitting clothes or jewellery that can get caught in moving parts.

Wear gloves and slip-proof shoes.

Wear a hairnet if your hair is long.

Wear protective clothing.

Safety goggles

Ear protection (sound intensity level at workplace can exceed 78 dB (A))

Dust mask

Keep your workplace in an orderly condition.

Take into consideration the environmental influences:

Do not use the device in moist or wet conditions.

Do not expose the chainsaw sharpener to rain.

Only work with sufficient visibility conditions. Provide good illumination.

Never leave the machine unattended.

Persons under the age of 18 must not operate the device.

Do not allow other people, especially children, to touch the sharpener.

Keep them away from your working area.

Do not overload the machine!

Only operate the machine with complete and correctly attached safety equipment.

Do not use any grinding wheels which do not comply with the indicated characteristics of this

instruction manual.

Worn and defective grinding wheels (cracks, imbalance, chipping, etc.) must be replaced

immediately.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Sharpener

Switch the machine off and remove the mains plug from the socket when:

Carrying out repairs

Maintenance and cleaning

Storage

Leaving the chainsaw sharpener (even in case of short-term interruptions)

Maintain your chainsaw sharpener with care:

Keep the sharpener free of oil and grease.

Follow the maintenance instructions and the instructions for tool exchange.

Check the machine for possible damage:

Before continuing to use the machine, the protective devices must be inspected to

ensure that they work perfectly for their intended function.

Check whether the movable parts function perfectly and do not stick or whether the parts

are damaged. All parts must be properly mounted and all conditions met to ensure the

flawless operation of the chainsaw sharpener.

Unless otherwise, indicated in the operating instructions, damaged safety devices and

parts must be properly repaired by an authorised workshop.

Damaged or illegible safety warning labels should be replaced immediately.

Do not allow any tool key to be plugged in!

Before switching on, check always that wrenches and adjusting tools are removed.

Store unused equipment in a dry, locked place out of reach of children.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Sharpener

Electrical Safety

Long and thin connection lines will result in a potential drop.

Plugs and coupler outlets on connection cables must be made of rubber, non-rigid PVC or

other thermoplastic material of the same mechanical stability.

The connector of the connection cable must be splash-proof.

When running the connection line, make sure it is neither bent or stretched

Never run the sharpener with a wet plug connection

Wind the cable completely when using a cable drum.

Only use the cable as it was intended.

Protect the cable against heat, oil and sharp edges.

Do not use the cable to pull the plug from the socket.

Protect yourself against electric shocks. Avoid touching earthed parts (e.g. pipes, heating

apparatus, cooker, fridges etc.)

Regularly check the extension cables and replace them if they are damaged.

Do not use any defective connection cables.

Do not set up any provisional electrical connections.

Never bypass protective devices or deactivate them.

The electrical connection or repairs to electrical parts of the machine must be carried out by a

certified electrician or by a representative of the manufacturer.

Use only original spare parts, accessories and special accessory parts. Accidents can arise for

the user through the use of other spare parts. The manufacturer is not liable for any damage or

injury resulting from such action.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Sharpener

Assembly

The chainsaw sharpener is delivered pre-assembled. It consists of the base, on which the chain

guide is located and the bearing arm with the motor and handgrip.

The assembly should be performed with the machine unplugged.

The sharpener is suited for both desk installation and wall mounting. When installing it on the

desk, put the machine on the edge of the desk and screw it to the desk using the holes in the

base.

When mounting on the wall, use the respective holes in the vertical part of the base (there should

be a maintained distance from the wall or alternately spacers can be used to gain access to the

rear set screw).

After the desk installation, fit the arm in the base by inserting the pilot pin and securing it with a

hexagonal screw (Fig. 1).

It is possible to fit a washer on the rear side screw and screw the setting wheel on. (Fig. 2).

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Sharpener

Screw the supporting arm control holder on the screw in the grinding disk body. (Fig. 3).

Fit the grinding disk enclosure in using the supplied screws and a respective wrench. (Fig. 4).

When mounting on the wall, carefully mount the machine at a height of 120-130 cm from the floor

to avoid working at eye height!

To be able to install the disk, unscrew the auxiliary flange. (Fig. 5).

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Sharpener

After you have removed the ancillary flange, you can insert the grinding disk in the body from

below. See that the ancillary flange and the disk abut against each other precisely. (Fig. 6).

Do not tighten the screws too much to avoid damaging to the disk. The grinding disk on the hub

torque is 7 Nm; you can adjust it using a torque spanner. Now, the grinding disk additional guard

should be fitted on (Fig. 7).

Check the correct bottoming of the disk: it should not move across and lengthwise. With the

grinding disk properly installed, a trial may be performed.

If the grinding disk is vibrating or shows otherwise wobbling, switch off and unplug the machine

before you attempt in clearing the fault.

The machine has a zero voltage circuit breaker, which is disabled on outage and will prevent any

restarting of the machine after the power supply is restored.

Using the sharpening stone and a clamping plate, it is possible to sharpen the disk to obtain the

required profile.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Sharpener

Grinding

Before the start of grinding, the chain should be conducted between both the attachment guides.

The sharpening angle must correspond to the guide’s position.

The type of chain to be sharpened can be determined using the sharpening block provided on

the dimension table.

Loosen the mounting screw (10b) and place the cutting chain in the guide rail between the guide

plate (Fig. 11).

Fold the chain stop (Fig.12) down and pull the chain toward the back until the cutting link rests

against the stop.

Set the top plate angle by means of the set screw (P.2, P.4); you can also use the scale to set

the angle. The vice angle should be setup by the set screw.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Sharpener

With the clamping screw adjusted and the vice angle setup (RH and LH teeth are different) and

pre-set to the top plate angle, set the distance with the help of the mounting screw (10a), lead the

grinding disk down to the tooth by soft pushing the supporting strut. The grinding depth may be

set by the set screw (K).

Tighten the mounting screw (10b); and after this you may switch the sharpener on. The chainsaw

sharpening may be started by gently pushing on the grinding disk. Adjust the pressure as

necessary. Mark the start of grinding with a piece of chalk and grind all the teeth in one direction,

then turn the clamping screw, minding the angle, and grind the teeth in the opposite direction.

With warn chains, the lateral guide position should be set at an angle where the grinding disk

can’t touch the guide.

While operating the sharpener, avoid strong thrusting as the teeth might collide and cause

excessive wear and tear of the chain.

Grinding depth Delimiter

The size of the depth delimiter can be determined by the table on page 11.

When you are grinding the depth delimiter, the screw clamp position should always be at a rate

of 0.

Set the supporting strut and holder at 90 degrees. The grind depth can be set using the set

screw K.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Sharpener

Dimensions

Chain

Pitch

Gauge

Oregon

Stihl

Sandvik

Carlton

Vise

Angle

Top Plate

Angle

Tilt

Angle

Wheel Width

Depth

Gauge

1/4”

0.050”/1.3mm

25AP

13RM

50K

30 ⁰

60 ⁰

10 ⁰

1/8”3.2mm

0.025”/0.63mm

0.325”

0.050”/1.3mm

20LP

23RS

50JLG

K1L

25 ⁰

60 ⁰

10 ⁰

1/8”3.2mm

0.025”/0.63mm

0.325”

0.058”/1.5mm

21LP

25RS

58JLG

K2L

25 ⁰

60 ⁰

10 ⁰

1/8”3.2mm

0.025”/0.63mm

0.325”

0.063”/1.6mm

22LP

26RS

63JLG

K3L

25 ⁰

60 ⁰

10 ⁰

1/8”3.2mm

0.025”/0.63mm

0.325”

0.050”/1.3mm

20BP

23RM

50JLG

K1C

30 ⁰

60 ⁰

10 ⁰

1/8”3.2mm

0.025”/0.63mm

0.325”

0.058”/1.5mm

21BP

25RM

58JLG

K2C

30 ⁰

60 ⁰

10 ⁰

1/8”3.2mm

0.025”/0.63mm

0.325”

0.063”/1.6mm

22BP

26RM

63JLG

K3C

30 ⁰

60 ⁰

10 ⁰

1/8”3.2mm

0.025”/0.63mm

0.325”

0.050”/1.3mm

95VP

K1N

30 ⁰

60 ⁰

10 ⁰

1/8”3.2mm

0.025”/0.63mm

0.325”

0.050”/1.3mm

95R

5 ⁰

50 ⁰

10 ⁰

1/8”3.2mm

0.030”/0.76mm

0.325”

0.058”/1.5mm

M21LP

25 ⁰

60 ⁰

10 ⁰

1/8”3.2mm

0.025”/0.63mm

0.325”

0.063”/1.6mm

M22LP

25 ⁰

60 ⁰

10 ⁰

1/8”3.2mm

0.025”/0.63mm

3/8”

0.050”/1.3mm

72LG

33RS

50AL

A1LM

25 ⁰

60 ⁰

10 ⁰

1/8”3.2mm

0.025”/0.63mm

3/8”

0.058”/1.5mm

73LG

35RS

58AL

A2LM

25 ⁰

60 ⁰

10 ⁰

1/8”3.2mm-

3/16”/4.7mm

0.025”/0.63mm

3/8”

0.063”/1.6mm

75LG

36RS

63AL

A3LM

25 ⁰

60 ⁰

10 ⁰

1/8”3.2mm-

3/16”/4.7mm

0.025”/0.63mm

3/8”

0.050”/1.3mm

72LP

33RS

50AG

A1L

25 ⁰

60 ⁰

10 ⁰

1/8”3.2mm-

3/16”/4.7mm

0.025”/0.63mm

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Sharpener

Chain

Pitch

Gauge

Oregon

Stihl

Sandvik

Carlton

Vise

Angle

Top Plate

Angle

Tilt

Angle

Wheel Width

Depth

Gauge

3/8”

0.058”/1.5mm

73LP

35RS

58AG

A2L

25 ⁰

60 ⁰

10 ⁰

1/8”3.2mm-

3/16”/4.7mm

0.025”/0.63mm

3/8”

0.063”/1.6mm

75LP

36RS

63AG

A3L

25 ⁰

60 ⁰

10 ⁰

1/8”3.2mm-

3/16”/4.7mm

0.025”/0.63mm

3/8”

0.050/1.3mm

72DP

33RMI

A1EP

35 ⁰

60 ⁰

0 ⁰

1/8”3.2mm-

3/16”/4.7mm

0.025”/0.63mm

3/8”

0.058”/1.5mm

73DP

A2EP

35 ⁰

60 ⁰

0 ⁰

1/8”3.2mm-

3/16”/4.7mm

0.025”/0.63mm

3/8”

0.063”/1.6mm

75DP

36RMI

A3EP

35 ⁰

60 ⁰

0 ⁰

1/8”3.2mm-

3/16”/4.7mm

0.025”/0.63mm

3/8”

0.050”/1.3mm

72RD

10 ⁰-15 ⁰

50 ⁰

10 ⁰

1/8”3.2mm-

3/16”/4.7mm

0.025”/0.63mm

3/8”

0.058”/1.5mm

73RD

10 ⁰-15 ⁰

50 ⁰

10 ⁰

1/8”3.2mm-

3/16”/4.7mm

0.025”/0.63mm

3/8”

0.063”/1.6mm

75RD

36RMX

10 ⁰-15 ⁰

50 ⁰

10 ⁰

1/8”3.2mm-

3/16”/4.7mm

0.025”/0.63mm

3/8”

0.058”/1.5mm

M73LP

25 ⁰

60 ⁰

10 ⁰

1/8”3.2mm-

3/16”/4.7mm

0.025”/0.63mm

3/8”

0.063”/1.6mm

M75LP

25 ⁰

60 ⁰

10 ⁰

1/8”3.2mm-

3/16”/4.7mm

0.025”/0.63mm

3/8 (90)

0.043”/1.1mm

90SG

63PMN

N4C

30 ⁰

60 ⁰

0 ⁰

1/8”3.2mm-

3/16”/4.7mm

0.020”/0.50mm

3/8 (91)

0.050”/1.3mm

91VS

63PM

50R

N1C

30 ⁰

60 ⁰

0 ⁰

1/8”3.2mm-

3/16”/4.7mm

0.025”/0.63mm

3/8 (91)

0.050”/1.3mm

91VG

63PMI

50RG

NIC-BC

30⁰

60 ⁰

0 ⁰

1/8”3.2mm-

3/16”/4.7mm

0.025”/0.63mm

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Sharpener

Chain

Pitch

Gauge

Oregon

Stihl

Sandvik

Carlton

Vise

Angle

Top Plate

Angle

Tilt

Angle

Wheel Width

Depth

Gauge

3/8 (91)

0.050”/1.3mm

91R

63PMX

5⁰

60 ⁰

0 ⁰

1/8”3.2mm-

3/16”/4.7mm

0.025”/0.63mm

0.404”

0.058”/1.5mm

581

B2LM

25⁰

60 ⁰

10 ⁰

3/16”/4.7mm

0.025”/0.63mm

0.404”

0.063”/1.6mm

591

B3LM

25⁰

60 ⁰

10 ⁰

3/16”/4.7mm

0.025”/0.63mm

0.404”

0.058”/1.5mm

26/P

58B

B2EP

35⁰

60 ⁰

10 ⁰

3/16”/4.7mm

0.030”/0.76mm

0.404”

0.063”/1.6mm

27/P

46RSE

63B

B3EP

35⁰

60 ⁰

10 ⁰

3/16”/4.7mm

0.030”/0.76mm

0.404”

0.063”/1.6mm

59AC

46RM

63BC

B3S

35⁰

60 ⁰

0 ⁰

3/16”/4.7mm

0.030”/0.76mm

0.404”

0.63”/1.6mm

27R

46RMX

63BR

B3RM10

10 ⁰-15 ⁰

50 ⁰

10 ⁰

3/16”/4.7mm

0.030”/0.76mm

0.404”

0.63”/1.6mm

16H

46RMH

HC

B3M

35⁰

60 ⁰

10 ⁰

3/16”/4.7mm

0.050”/1.27mm

0.404”

0.080”/2.0mm

18H

49RMH

2HC

B3M

35⁰

60 ⁰

10 ⁰

3/16”/4.7mm

0.050”/1.27mm

3/4”

0.122”/3.1mm

11H

G7S

35⁰

60 ⁰

10 ⁰

1/4”/6mm

0.050”/1.27mm

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Chainsaw Sharpener

Specifications

Type

SH0910

Operating Voltage

220-240V

Rated Power

230W

Max. Power

Output: 350W @ 50% Duty Cycle

Max. Motor RPM

3,000 RPM

Motor Rating P1

350W

Max. Cutting Length

250mm

Vice Capacity

0.80" to 0.50"

Light Wattage

35W

Max. Working Angle

35 Degrees Left to Right

Grinding Disc Size

145 x 3.2 x 22.3mm Arbor

Approvals

CE, GS, C-TICK, EMC

Lwa / Lpa

85/72 dB (A)

Gross Weight

8 kg

Vibration

3.21 m/s2

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Some experts believe the incorrect or prolonged use of almost any

product could causeserious injury or death. For information that

may reduce your risk of serious injury or death consult thepoints

below and additionally, the information available at

www.datastreamserver.com/safety

- Consult all documentation, packaging and

product labelling be fore use. Note that some

products feature online documentation which

should be printed and kept with the product.

- Check product for loose / broken / damaged /

missing parts, wear or leaks (if applicable) be fore

each use. Never use a product with loose / broken

/ damaged / missing pa rts, wear or leaks (if

applicable).

- Products must be inspected and serviced (if

applicable) by a qualified specialist every 6

months assuming average residential use by a

person of average weight and strength, ab ove

average technical aptitude, on a property

matching average metropolitan specification.

Intended use outside these guidelines could

indicate the product is not suitable for intended

use or may require more regular inspection or

servicing.

- Ensure all possible users of the p roduct have

completed an industry recognised training course

before being given access to the product.

- The product has been supplied by a general merchandise

retailer that may not be familiar with your specific applic ation or

your description of the application. Be sure to attain third party

approval for your application from a qualified specialist before use

regardless of prior assurances by the retailer or its representatives.

- This product is not intended for use where fail-safe operation is

required. As with any product (take an au tomobile, aircraft,

computer or ball point pen for example) there is always a small

chance of a technical issue that needs to be repaired or may

require replacement of the product or a part. If the possibility of

such failure and the associated time it takes to rectify could in any

situation inconvenience the user, business or employee or could

financially affect the user, business or employee then the product

is not suitable for your requirements. This p roduct is not for use

where incorrect operation or a failure of any kind, including but

not limited to a condition requiring product return, replacement,

service by a technician or replacement of parts could cause a

financial loss, loss of employee time or an in convenience

requiring compensation.

- If this item has been purchased in error considering the points

above simply contact the retailer directly for details of their

returns policies if required.

Baumr-AG SH0910 User manual

Popular Power Tools manuals by other brands