Baumr-ag Cm-210 User manual

Compound Mitre Saw – CM-210

User Manual

[Revision 2.0 February 2020]

READ THIS MANUAL CAREFULLY BEFORE USE – FAILURE TO DO SO MAY RESULT IN INJURY, PROPERTY DAMAGE

AND MAY VOID WARRANTY. • KEEP THIS MANUAL FOR FUTURE REFERENCE. • Products covered by this manual may

vary in appearance, assembly, inclusions, specifications, description and packaging.

Compound Mitre Saw – CM-210

Safety

Safety messages are designed to alert you to possible dangers or hazards that could cause death, injury or

equipment or property damage if not understood or followed. Safety messages have the following symbols:

You WILL be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be KILLED or

SERIOUSLY INJURED if you do

not follow instructions.

You CAN be INJURED if you do

not follow instructions or equipment

damage may occur.

It is vital that you read and understand this

user manual before using the product,

including safety warnings, and any assembly

and operating instructions. Keep the manual

for future reference.

Safety precautions and recommendations

detailed here must be fully understood and

followed to reduce the risk of injury, fire,

explosion, electrical hazard, and/or property

damage.

Safety information presented here is generic

in nature – some advice may not be

applicable to every product. The term

"equipment" refers to the product, be it

electrical mains powered, battery powered or

combustion engine powered.

•Before Use - If you are not familiar with the

safe operation/handling of the equipment or

are in any way unsure of any aspect of

suitability or correct use for your

application, you should complete training

conducted by a person or organization

qualified in safe use and operation of this

equipment, including fuel/electrical handling

and safety.

•Do NOT operate the equipment in

flammable or explosive environments, such

as in the presence of flammable liquids,

gases or dust. The equipment may create

sparks or heat that may ignite flammable

substances.

•Keep clear of moving parts.

•Equipment may be a potential source of

electric shock or injury if misused.

•Do NOT operate the equipment if it is

damaged, malfunctioning or is in an

excessively worn state.

•Do NOT allow others to use the equipment

unless they have read this manual and are

adequately trained.

•Keep packaging away from children - risk

of suffocation! Operators must use the

equipment correctly. When using the

equipment, consider conditions and pay

due care to persons and property.

General Work Area Safety

•Work areas should be clean and well it.

•Do not operate the equipment if

bystanders, animals etc are within

operating range of the equipment or the

general work area.

•If devices are provided for connecting dust

extraction / collection facilities, ensure

these are connected and used properly.

Dust collection can reduce dust-related

hazards.

General Personal Safety

•Wear appropriate protective equipment

when operating, servicing, or when in the

operating area of the equipment to help

protect from eye and ear injury, poisoning,

burns, cutting and crush injuries. Protective

equipment such as safety goggles,

respirators, non-slip safety footwear, hard

hat, hearing protection etc should be used

for appropriate equipment / conditions.

Other people nearby should also wear

appropriate personal protective equipment.

Do not wear loose clothing or jewellery,

which can be caught in moving parts. Keep

hair and clothing away from the equipment.

•Stay alert and use common sense when

operating the equipment. Do not over-

reach. Always maintain secure footing and

balance.

•Do not use the equipment if tired or under

the influence of drugs, alcohol or

medication.

•This equipment is not intended for use by

persons with reduced physical, sensory or

mental capabilities.

General Fuel Safety

•Petrol/fuel/gasoline is extremely flammable

– keep clear of naked flames or other

ignition sources.

•Do not spill fuel. If you spill fuel, wipe it off

the equipment immediately – if fuel gets on

your clothing, change clothing.

•Do NOT smoke near fuel or when

refuelling.

•Always shut off the engine before

refuelling.

•Do NOT refuel a hot engine.

•Open the fuel cap carefully to allow any

pressure build-up in the tank to release

slowly.

•Always refuel in well ventilated areas.

•Always check for fuel leakage. If fuel

leakage is found, do not start or run the

engine until all leaks are fixed.

General Carbon-Monoxide Safety

•Using a combustion engine indoors CAN

KILL IN MINUTES. Engine exhaust

contains carbon-monoxide – a poison you

cannot smell or see.

•Use combustion engines OUTSIDE only,

and far away from windows, doors and

vents.

General Equipment Use and Care

•The equipment is designed for domestic

use only.

•Handle the equipment safely and carefully.

•Before use, inspect the equipment for

misalignment or binding of moving parts,

loose components, damage or any other

condition that may affect its operation. If

damaged, have the equipment repaired by

an authorised service centre or technician

before use.

•Prevent unintentional starting of the

equipment - ensure equipment and power

switches are in the OFF position before

connecting or moving equipment. Do not

carry equipment with hands or fingers

touching any controls. Remove any tools or

other items that are not a part of the

equipment from it before starting or

switching on.

•Do not force the equipment. Use the

correct equipment for your application.

Equipment will perform better and be safer

when used within its design and usage

parameters.

•Use the equipment and accessories etc. in

accordance with these instructions,

considering working conditions and the

work to be performed. Using the equipment

for operations different from those intended

could result in hazardous situations.

•Always keep equipment components

(engines, hoses, handles, controls, frames,

housings, guards etc) and accessories

(cutting tools, nozzles, bits etc) properly

maintained. Keep the equipment clean and,

where applicable, properly lubricated.

•Store the equipment out of reach of

children or untrained persons. To avoid

burns or fire hazards, let the equipment

cool completely before transporting or

storing. Never place or store the equipment

near flammable materials, combustible

gases or liquids etc.

•The equipment is not weather-proof, and

should not be stored in direct sunlight, at

high ambient temperatures or locations that

are damp or humid.

•Do not clean equipment with solvents,

flammable liquids or harsh abrasives.

•For specific equipment safety use and care,

see Equipment Safety.

Compound Mitre Saw – CM-210

General Electrical Safety

•Inspect electrical equipment, extension

cords, power bars, and electrical fittings for

damage or wear before each use. Repair or

replace damaged equipment immediately.

•Ensure all power sources conform to

equipment voltage requirements and are

disconnected before connecting or

disconnecting equipment.

•When wiring electrically powered

equipment, follow all electrical and safety

codes.

•Wherever possible, use a residual current

device (RCD).

•High voltage / high current power lines may

be present. Use extreme caution to avoid

contact or interference with power lines.

Electrical shock can be fatal.

General Electrical Safety

•Electrically grounded equipment must have

an approved cord and plug and be

connected to a grounded electrical outlet.

•Do NOT bypass the ON/OFF switch and

operate equipment by connecting and

disconnecting the electrical cord.

•Do NOT use equipment that has exposed

wiring, damaged switches, covers or

guards.

•Do NOT use electrical equipment in wet

conditions or in damp locations.

•Do NOT use electrical cords to lift, move or

carry equipment.

•Do NOT coil or knot electrical cords, and

ensure electrical cords are not trip hazards.

General Service Information

•The equipment must be serviced or

repaired at authorised service centres by

qualified personnel only.

•Replacement parts must be original

equipment manufacturer (OEM) to ensure

equipment safety is maintained.

•Do NOT attempt any maintenance or repair

work not described in this manual.

•After use, the equipment and components

may still be hot – allow the equipment to

cool and disconnect spark plugs and/or

electrical power sources and/or batteries

from it before adjusting, changing

accessories or performing repair or

maintenance.

•Do NOT adjust while the equipment is

running.

•Perform service related activities in suitable

conditions, such as a workshop.

•Replace worn, damaged or missing

warning/safety labels immediately.

INTRODUCTION

According to the applicable product liability laws, the manufacturer of the device does not assume liability for damages to the product or damages

caused by the product that occurs due to:

•Improper handling,

•Non-compliance of the operating instructions,

•Repairs by third parties, not by authorized service technicians,

•Installation and replacement of non-original spare parts,

•Application other than specified,

•A breakdown of the electrical system that occurs due to the non-compliance of the electric regulations and VDE regulations 0100, DIN 57113 /

VDE0113.

Read through the complete text in the operating instructions before installing and commissioning the device.

The operating instructions are intended to help the user to become familiar with the machine and take advantage of its application possibilities in

accordance with the recommendations.

The operating instructions contain important information on how to operate the machine safely, professionally and economically, how to avoid

danger, costly repairs, reduce downtimes and how to increase reliability and service life of the machine. In addition to the safety regulations in the

operating instructions, you have to meet the applicable regulations that apply for the operation of the machine in your country.

Keep the operating instructions package with the machine at all times and store it in a plastic cover to protect it from dirt and moisture. Read the

instruction manual each time before operating the machine and carefully follow its information.

The machine can only be operated by persons who were instructed concerning the operation of the machine and who are informed about the

associated dangers. The minimum age requirement must be complied with.

In addition to the safety instructions contained in this operating manual and the specific regulations of your country, the technical rules generally

accepted for the operation of machines of the same type must be observed.

We accept no liability for damage or accidents which arise due to non-observance of these instructions and the safety information.

INTENDED USE

The mitre saw is designed to crosscut wood and plastic respective of the machine’s size. The saw is not designed for cutting firewood.

Warning! Do not use the saw to cut materials other than those specified described in manual.

Warning! The supplied saw blade is only intended for the sawing of wood! Do not use this blade for the sawing of firewood!

The equipment is to be used only for its prescribed purpose. Any other use is deemed to be a case of misuse. The user / operator and not the

manufacturer will be liable for any damage or injuries of any kind caused as a result of this.

The equipment is to be operated only with suitable saw blades. It is prohibited to use any type of cutting-off wheel.

To use the equipment properly you must also observe the safety information, the assembly instructions and the operating instructions to be found in

this manual.

All persons who use and service the equipment have to be acquainted with this manual and must be informed about the equipment’s potential

hazards. It is also imperative to observe the accident prevention regulations in force in your area. The same applies for the general rules of health

and safety at work.

The manufacturer will not be liable for any changes made to the equipment nor for any damage resulting from such changes. Even when the

equipment is used as prescribed it is still impossible to eliminate certain residual risk factors. The following hazards may arise in connection with the

machine’s construction and design:

Compound Mitre Saw – CM-210

•Contact with the saw blade in the uncovered saw zone.

•Reaching into the running saw blade (cut injuries).

•Kick-back of workpieces and parts of workpieces.

•Saw blade fracturing.

•Catapulting of faulty carbide tips from the saw blade.

•Damage to hearing if ear-muffs are not used as necessary.

•Harmful emissions of wood dust when used in closed rooms.

Please note that our equipment has not been designed for use in commercial, trade or industrial applications. Our warranty will be voided if the

equipment is used in commercial, trade or industrial businesses or for equivalent purposes.

GENERAL SAFETY INFORMATION FOR POWER TOOLS

WARNING! Read all safety warnings, instructions, illustrations and technical data provided with this power tool. Failure to follow the

warnings and instructions may result in electric shock, fire and/ or serious injury.

Save all warnings and instructions for future reference. The term “power tool” used in the safety instructions refers to mains powered power

tools (with power cord) and cordless power tools (without power cord).

WORKPLACE SAFETY

•Keep your workplace clean and well illuminated. Disorderliness and poorly illuminated workplaces may lead to accidents.

•Do not operate the power tool in explosive atmospheres with inflammable liquids, gases or dust. Power tools generate sparks which may ignite

dust or vapours.

•Keep children and other persons away from the power tool during operation. You may lose control of the tool if you are distracted.

ELECTRIC SAFETY

•The plug of the power tool must fit into the socket. Do not modify the plug in any way. Do not use adapter plugs together with grounded power

tools. Unmodified plugs and matching sockets reduce the risk of electric shock.

•Avoid body contact with grounded surfaces such as pipes, radiators, ovens and refrigerators. There is an increased risk of electric shock if your

body is grounded.

•Keep power tools away from rain or humidity. Water permeation into the power tool will increase the risk of electric shock.

•Use the cable solely for its intended purpose. Do not use the cable to carry or hang up the power tool or to pull out the plug from the socket. Keep

the cable away from heat, oil, sharp edges or moving machine parts. Damaged or twisted cables increase the risk of electric shock.

•When working outdoors with power tools, only use extension cords which are suited for outdoor areas. Using extension cords suited for outdoor

applications reduces the risk of electric shock.

•If the operation of power tools in a humid environment cannot be avoided, you must use a residual current circuit breaker. The use of a residual

current circuit breaker will reduce the risk of electric shock.

PERSONAL SAFETY

•Pay attention to what you are doing and use power tools sensibly. Do not use power tools when you are tired or under the influence of drugs,

alcohol or medication. A single moment of inattention while using power tools may cause severe injury.

•Wear personal protective equipment and safety goggles. Wearing personal protective equipment such as a dust mask, non-skid safety boots, a

protective helmet or hearing protection according to the type and application of the power tool reduces the risk of injury.

•Avoid starting the power tool unintentionally. Make sure that the power tool is switched off before you connect it to the mains and/ or insert a

battery, pick it up or carry it. lf you have your finger on the switch when you carry the power tool, or if the machine is switched on when you

connect it to the mains, this may result in accidents.

•Remove adjustment tools or wrenches before switching on the power tool. Tools or wrenches in rotating machine parts may cause injury.

•Avoid abnormal body positions. Stand securely and keep your balance at all times. By doing so, you can control the power tool more easily in

unexpected situations.

•Wear suitable clothing. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothing,

jewellery or long hair may be trapped in moving parts.

•If dust extraction tools or collection bins can optionally be attached, you must make sure that they are connected and correctly used. Using dust

extraction tools may reduce risks caused by dust.

•Do not let familiarity gained from frequent use of the tool allow you to become complacent and ignore tool safety principles. A careless action can

cause severe injury within a fraction of a second.

•Wear hearing protection. The effects of noise can cause a loss of hearing.

•Try to keep emissions as low as possible, for example by limiting your working time. In this regard, all the operational cycle phases must be taken

into consideration (such as the times when the tool is switched off or running idle).

USE AND TREATMENT OF THE POWER TOOL

•Do not overload the tool. Use the appropriate power tool for your type of work. With appropriate power tools, you can work better and more safely

within the given power range.

•Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must

be repaired.

•Disconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments,

changing accessories, or storing power tools. This preventive safety measure reduces the risk of starting the power tool accidentally.

•Store idle power tools out of the reach of children. Do not allow persons unfamiliar with the power tool or these instructions to operate the power

tool. Power tools are dangerous in the hands of untrained users.

Compound Mitre Saw – CM-210

•Carefully maintain power tools and accessories. Check moving parts for proper function and smooth running, and check whether there are parts

which are broken or damaged to the extent that the functionality of the power tool is impaired.

•Have damaged parts repaired before using the power tool. Many accidents are caused by poorly-maintained power tools.

•Keep cutting tools sharp and clean. Carefully maintained cutting tools with sharp edges are less likely to jam and can be guided more easily.

•Use power tools, accessory parts, insertion tools, etc. in compliance with these instructions. Take into account the working conditions and the

activity which is to be carried out. Using power tools for applications other than those intended may cause dangerous situations.

•Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe

handling and control of the power tool in unexpected situations.

SERVICE

•Have your power tool repaired by qualified specialists only, and always use original spare parts for repair. This is to maintain the safety of the

power tool.

•Warning! This electric tool generates an electromagnetic field during operation. This field can impair active or passive medical implants under

certain conditions. In order to prevent the risk of serious or deadly injuries, we recommend that persons with medical implants consult with their

physician and the manufacturer of the medical implant prior to operating the electric tool.

SAFETY INSTRUCTIONS FOR MITRE SAWS

•Mitre saws are intended to cut wood or wood like products, they cannot be used with abrasive cut-off wheels for cutting ferrous material such as

bars, rods, studs, etc. Abrasive dust causes moving parts such as the lower guard to jam. Sparks from abrasive cutting will burn the lower guard,

the kerf insert and other plastic parts.

•Use clamps to support the workpiece whenever possible. If supporting the workpiece by hand, you must always keep your hand at least 100 mm

from either side of the saw blade. Do not use this saw to cut pieces that are too small to be securely clamped or held by hand. If your hand is

placed too close to the saw blade, there is an increased risk of injury from blade contact.

•The workpiece must be stationary and clamped or held against both the fence and the table. Do not feed the workpiece into the blade or cut

“freehand” in any way. Unrestrained or moving workpieces could be thrown at high speeds, causing injury.

•Push the saw through the workpiece. Do not pull the saw through the workpiece. To make a cut, raise the saw head and pull it out over the

workpiece without cutting, start the motor, press the saw head down and push the saw through the workpiece. Cutting on the pull stroke is likely

to cause the saw blade to climb on top of the workpiece and violently throw the blade assembly towards the operator.

•Never cross your hand over the intended line of cutting either in front or behind the saw blade. Supporting the workpiece “cross handed” i.e.

holding the workpiece to the right of the saw blade with your left hand or vice versa is very dangerous.

•Do not reach behind the fence with either hand closer than 100 mm from either side of the saw blade, to remove wood scraps, or for any other

reason while the blade is spinning. The proximity of the spinning saw blade to your hand may not be obvious and you may be seriously injured.

•Inspect your workpiece before cutting. If the workpiece is bowed or warped, clamp it with the outside bowed face toward the fence. Always make

certain that there is no gap between the workpiece, fence and table along the line of the cut. Bent or warped workpieces can twist or shift and

may cause binding on the spinning saw blade while cutting. There should be no nails or foreign objects in the workpiece.

•Do not use the saw until the table is clear of all tools, wood scraps, etc., except for the workpiece. Small debris or loose pieces of wood or other

objects that contact the revolving blade can be thrown with high speed.

•Cut only one workpiece at a time. Stacked multiple workpieces cannot be adequately clamped or braced and may bind on the blade or shift

during cutting.

•Ensure the mitre saw is mounted or placed on a level, firm work surface before use. A level and firm work surface reduces the risk of the mitre

saw becoming unstable.

•Plan your work. Every time you change the bevel or mitre angle setting, make sure the adjustable fence is set correctly to support the workpiece

and will not interfere with the blade or the guarding system. Without turning the tool “ON” and with no workpiece on the table, move the saw blade

through a complete simulated cut to assure there will be no interference or danger of cutting the fence.

•Provide adequate support such as table extensions, saw horses, etc. for a workpiece that is wider or longer than the tabletop. Workpieces longer

or wider than the mitre saw table can tip if not securely supported. If the cut-off piece or workpiece tips, it can lift the lower guard or be thrown by

the spinning blade.

•Do not use another person as a substitute for a table extension or as additional support. Unstable support for the workpiece can cause the blade

to bind or the workpiece to shift during the cutting operation pulling you and the helper into the spinning blade.

•The cut-off piece must not be jammed or pressed by any means against the spinning saw blade. If confined, i.e. using length stops, the cut-off

piece could get wedged against the blade and thrown violently.

•Always use a clamp or a fixture designed to properly support round material such as rods or tubing. Rods have a tendency to roll while being cut,

causing the blade to “bite” and pull the work with your hand into the blade.

•Let the blade reach full speed before contacting the workpiece. This will reduce the risk of the workpiece being thrown.

•If the workpiece or blade becomes jammed, turn the mitre saw off. Wait for all moving parts to stop and disconnect the plug from the power

source and/or remove the battery pack. Then work to free the jammed material. Continued sawing with a jammed workpiece could cause loss of

control or damage to the mitre saw.

•After finishing the cut, release the switch, hold the saw head down and wait for the blade to stop before removing the cut-off piece. Reaching with

your hand near the coasting blade is dangerous.

•Hold the handle firmly when making an incomplete cut or when releasing the switch before the saw head is completely in the down position. The

braking action of the saw may cause the saw head to be suddenly pulled downward, causing a risk of injury.

•The work piece must have a minimum height of 3 mm and a minimum width of 10 mm. Make sure that the workpiece is always secured with the

clamping device.

SAFETY INSTRUCTIONS FOR THE HANDLING OF SAW BLADES

•Do not use damaged or deformed saw blades.

•Do not use any insertion tools with cracks. Sort out cracked insertion tools. Repairs are not permitted.

Compound Mitre Saw – CM-210

•Do not use saw blades made of high speed steel.

•Check the condition of the saw blades before using the crosscut, drag and mitre saw.

•Make sure that a suitable saw blade for the material to be cut is selected.

•Only use saw blades recommended by the manufacturer. Saw blades designed to cut wood and similar materials must comply with EN 847-1.

•Do not use saw blades made of high-speed alloy steel (HSS steel).

•Only use saw blades for which the maximum permissible speed is not lower than the maximum spindle speed of the crosscut, drag and mitre

saw, and which are suitable for the material to be cut.

•Observe the saw blade direction of rotation.

•Only insertion the saw blade if you have mastered their use.

•Observe the maximum speed. The maximum speed specified on the insertion tool may not be exceeded. If specified, observe the speed range.

•Clean grease, oil and water off of the clamping surfaces.

•Do not use any loose reducing rings or bushes for the reducing of holes on saw blades.

•Make sure that fixed reducer rings for securing the insertion tool have the same diameter and have at least 1/3 of the cutting diameter.

•Make sure that fixed reducer rings are parallel to each other.

•Handle insertion tool with caution. They are ideally stored in the originally package or special containers. Wear protective gloves in order to

improve grip and to further reduce the risk of injury.

•Prior to the use of insertion tools, make sure that all protective devices are properly fastened.

•Prior to use, make sure that the insertion tool meets the technical requirements of this electric tool and is properly fastened.

•Only use the supplied saw blade for cutting wood, never for the processing of metals.

•Only use saw blade diameters in accordance with the markings on the saw.

•Use additional workpiece supports, if required for workpiece stability.

•Workpiece support extensions must always be secured and used during work.

•Replace table inserts when worn!

•Avoid overheating of the saw teeth.

•When sawing plastic, avoid melting of the plastic.

•Use the appropriate saw blades for this purpose.

•Replace damaged or worn saw blades immediately.

•When the saw blade overheats, stop the machine.

•Allow the saw blade to cool down before using the machine again.

•Attention: Laser radiation Do not stare into the beam Class 2 laser.

•Protect yourself and your environment from accidents using suitable precautionary measures!

•Do not look directly into the laser beam with unprotected eyes.

•Never look into the path of the beam.

•Never point the laser beam towards reflecting surfaces and persons or animals. Even a laser beam with a low output can cause damage to the

eyes.

•Caution - methods other than those specified here can result in dangerous radiation exposure.

•Never open the laser module. Unexpected exposure to the beam can occur.

•If you do not use the device for a long time, the batteries should be removed.

•The laser may not be replaced with a different type of laser.

•Repairs of the laser may only be carried out by the laser manufacturer or an authorised representative.

RESIDUAL RISKS

The machine has been built according to the state of the art and the recognised technical safety requirements. However, individual

residual risks can arise during operation.

•Health hazard due to electrical power, with the use of improper electrical connection cables.

•Furthermore, despite all precautions having been met, some non-obvious residual risks may still remain.

•Residual risks can be minimised if the “safety instructions” and the “Proper use” are observed along with the whole of the operating instructions.

•Do not load the machine unnecessarily: excessive pressure when sawing will quickly damage the saw blade, which results in reduced output of

the machine in the processing and in cut precision.

•When cutting plastic material, please always use clamps: the parts which should be cut must always be fixed between the clamps.

•Avoid accidental starting of the machine: the operating button may not be pressed when inserting the plug in an outlet.

•Use the tool that is recommended in this manual. In doing so, your machine provides optimal performance.

•Hands may never enter the processing zone when the machine is in operation.

•Release the handle button and switch off the machine prior to any operations.

Compound Mitre Saw – CM-210

Safety Symbols

The product may have safety warning labels attached to it, explained below. Understand the symbols on your

product and their meanings. If any stickers become unreadable, unattached etc., replace them.

Flammable Material Hazard

Flammable liquids, gases or

substances etc may present.

Avoid ignition sources and open

flames. Danger of fire.

Read User Manual

Read and fully understand

product safety warnings,

operation, procedures etc before

using the product.

Use Hand Protection

Wear appropriate hand protection

and take due care as the product

or use of the product may present

hand hazards.

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Electrocution / Electrical Shock

Hazard

High voltage or high current

electricity may be present or

required by the product. Take

due care when handling electrical

products, cables, plugs and

leads. Electrical shock can be

fatal.

Toxic Fumes / Dust Hazard

Using the product or by-products

from use may produce fumes,

smoke or particles that could be

harmful if inhaled. Wear

appropriate breathing protection

and have adequate ventilation.

Explosive Material Hazard

Combustible liquids, gases or

substances etc may be present.

Avoid ignition sources and open

flames. Danger of explosion.

Cutting / Amputation Hazard

The product may have blades,

edges or mechanical devices that

can cause severe cut injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Crush Hazard

The product may have blades,

edges or mechanical devices that

can cause severe crush injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Single Operator Only

The product must be operated by

a single person only. More than

one person operating the product

may introduce additional hazards.

Use Face Protection

Wear appropriate full-face

protection and take due care as

the product or use of the product

may present face and eye

hazards.

Use Foot Protection

Wear appropriate foot protection

and take due care as the product

or use of the product may present

foot hazards.

Use Eye / Ear / Head Protection

Wear appropriate eye and / or

ear and / or head protection and

take due care as the product or

use of the product may present

eye, hearing and head hazards.

Running Hazard

Do not run on or near the product

as doing so may present a fall

hazard.

Diving Hazard

Do not dive into the product as

doing so may present a neck /

head injury hazard.

Adult Supervision Required

Always supervise children and

other users of a product to

prevent drowning or injury.

Skin Penetration / Puncture

Hazard

The product may produce

pressure, emit liquids or objects

that can cause severe injury to

fingers, limbs, blood etc. Take

due care when handling and

using the product.

Hot Surface Hazard

Be aware that the product may

produce high temperatures and

hot surfaces that can cause burn

injuries.

Flying Debris Hazard

Be aware that the product or use

of the product may present

hazards produced by flying

debris. Wear appropriate clothing

and protective devices.

Moving Parts Hazard

Be aware that the product

contains or uses mechanical

devices that move or rotate.

Always wait for moving parts to

stop fully before handling the

product, adjusting, maintenance

etc.

Compound Mitre Saw – CM-210

Carbon-Monoxide Hazard

Do not use the product in

confined areas or without

adequate ventilation. Carbon-

monoxide poisoning can be fatal.

Pull Hazard

Be aware that the product

contains or uses mechanical

devices that can pull in objects

and can cause severe injury to

fingers, limbs etc. Take due care

when handling and using the

product.

Slope / Fall Injury Hazard

Be aware that using the product

on sloping surfaces or in slippery

conditions may present additional

dangers from falls and contact

with blades, moving parts, hot

surfaces etc.

"Slam Dunk" Warning

Do NOT attempt "slam dunk"

manoeuvres as this may result in

severe injury due to falling,

product breakage or collapse etc.

Electrocution / Electrical Shock

Hazard - Outdoor

High voltage or high current

electricity may be present or

required by the product. Do NOT

use in rain, damp or wet

conditions. Electrical shock can

be fatal.

Electrocution / Electrical Shock

Hazard - Disconnect

High voltage or high current

electricity may be present or

required by the product. Always

disconnect the product from the

electrical supply before handling

the product, adjusting,

maintenance etc.

Power Line Electrocution

Hazard

High voltage / high current power

lines may be present. Use

extreme caution to avoid contact

or interference with power lines.

Electrical shock can be fatal.

"Kick-Back" Hazard

High level of "kick-back" hazard

that can cause the machine to

suddenly rotate towards operator.

Kick-back injury can be fatal.

Winch Operator Position

Hazard

Do NOT stand between winch

and load. Do NOT use winch to

move people.

Winch Lift Hazard

Do NOT LIFT load vertically. Use

machine to PULL only.

Cable Hazard

Ensure that load bearing cable is

not kinked or knotted.

Winch Cable Hazard

Ensure that there is a minimum

number of cable coils on

winching mechanism.

Winch Hook Hazard

Carry hook to load – do NOT

throw or run.

Flash / Blinding Hazard

Wear appropriate eye protection

for welding. Direct exposure to

weld arcs may cause permanent

eye injury.

Laser Hazard

Laser may be in use – do NOT

look directly at laser or allow

others to.

Compound Mitre Saw – CM-210

Table of Contents

Safety .............................................................................................................................................................2

Safety Symbols...........................................................................................................................................................7

Parts Identification .....................................................................................................................................10

Before Starting the Equipment..................................................................................................................15

Checking the Moving Saw Blade Guard Safety Device ...........................................................................................15

Attachment and Operation.........................................................................................................................16

Attaching the Mitre Saw............................................................................................................................................16

Precision Adjustment of The Stop for Crosscut 90° .................................................................................................18

Crosscut 90° and Turntable 0° .................................................................................................................................20

Crosscut 90° and Turntable 0° - 45°.........................................................................................................................22

Precision Adjustment of the Stop for Mitre Cut 45° ..................................................................................................23

Mitre Cut 0°- 45° and Turntable 0° ...........................................................................................................................25

Mitre cut 0°- 45° and Turntable 0°- 45° ....................................................................................................................26

Limiting the Cutting Depth ........................................................................................................................................27

Sawdust Bag.............................................................................................................................................................28

Connection to an External Dust Extractor ................................................................................................................28

Changing the Saw Blade ..........................................................................................................................................29

Using the Laser.........................................................................................................................................................31

Adjusting the Laser...................................................................................................................................................31

Transport .....................................................................................................................................................32

Maintenance ................................................................................................................................................32

General Maintenance Measures ..............................................................................................................................32

Cleaning the Moving Saw Blade Guard Safety Device ............................................................................................32

Brush Inspection .......................................................................................................................................................32

Storage ........................................................................................................................................................33

Troubleshooting .........................................................................................................................................33

Specifications .............................................................................................................................................34

Compound Mitre Saw – CM-210

Parts Identification

No. Name No. Name No. Name

1

Handle

12

Scale

23

Stop for cutting depth limiting

2

ON/OFF switch

13

Rotary table

24

Adjusting screw (90°)

3 Lock switch 14 Fixed saw table 25 Adjusting screw (45°)

4 Machine head 15 Stop rail 26 Flange screw

5 Moving saw blade guard 16 16a. Movable stop rail

16b. Set screw 27 Outer flange

6

Saw blade

17

Sawdust bag

28

Saw shaft lock

7 Clamping device 18 Scale 29 Inner flange

8 Workpiece support 19 Pointer 30 Laser

9

Table insert

20

Set screw

31

ON/OFF switch laser

10

Set screw for rotary table

21

Locking bolt

32

Guide bracket

11

Pointer

22

Screw for cutting depth limiting

33

Tilt protection

A 90° stop angle (not supplied) B 45° stop angle (not supplied) C Allen key, 6 mm

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Compound Mitre Saw – CM-210

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Compound Mitre Saw – CM-210

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Compound Mitre Saw – CM-210

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Compound Mitre Saw – CM-210

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Compound Mitre Saw – CM-210

Before Starting the Equipment

ATTENTION! The device and packaging materials are not toys! Children must not be allowed to

play with plastic bags, film and small parts! There is a risk of swallowing and suffocation!

•Open the packaging and remove the device carefully.

•Remove the packaging material as well as the packaging and transport bracing (if available).

•Check that the delivery is complete.

•Check the device and accessory parts for transport damage.

•If possible, store the packaging until the warranty period has expired.

•The equipment must be set up where it can stand securely. Secure the machine on a workbench or a base

frame with 4 screws (not included in delivery) using the holes on the fixed saw table (14).

•Mount the tilt protection (33).

•All covers and safety devices have to be properly fitted before the equipment is switched on.

•It must be possible for the blade to run freely.

•When working with wood that has been processed before, watch out for foreign bodies such as nails or

screws, etc.

•Before you press the ON/OFF switch check that the saw blade is fitted correctly. Moving parts must run

smoothly.

•Before you connect the equipment to the power supply make sure the data on the rating plate are identical to

the mains data.

Checking the Moving Saw Blade Guard Safety Device

The saw blade guard protects against accidental contact with the saw blade and from chips flying around.

Check function

To do so, fold the saw downwards:

•The saw blade guard must provide free access to the saw blade without touching other parts.

•When folding the saw upwards into the starting position, the saw blade guard must cover the saw blade

automatically.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Compound Mitre Saw – CM-210

Attachment and Operation

Attaching the Mitre Saw

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Compound Mitre Saw – CM-210

1. In order to adjust the rotary table (13), loosen the set screw (10) approximately 2 turns.

2. Turn the rotary table (13) and pointer (11) to the desired angle measurement on the scale (12) and use the

set screw (10) to secure it.

3. Pressing the machine head (4) lightly downwards and removing the locking bolt (21) from the motor bracket

at the same time disengages the saw from the lowest position.

4. Swing the machine head (4) up.

5. It is possible to secure the clamping devices (7) to the left or right on the fixed saw table (14). Insert the

clamping devices (7) in the holes on the rear side of the stop rail (15) and secure it with the star grip screws

(7a).

For 0°- 45° mitre cuts, the clamping device (7) must only be mounted on the right side (see fig. 11-12).

6. It is possible to tilt the machine head (4) a max. 45° to the left by loosening the set screw (20).

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Compound Mitre Saw – CM-210

Precision Adjustment of The Stop for Crosscut 90°

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Compound Mitre Saw – CM-210

No stop angle included.

1. Lower the machine head (4) and secure it using the locking bolt (21).

2. Loosen the set screw (20).

3. Position the angle stop (A) between the saw blade (6) and the rotary table (13).

4. Loosen the lock nut (24a).

5. Adjust the adjusting screw (24) until the angle between the saw blade (6) and rotary table (13) is 90°.

6. Re-tighten the lock nut (24a).

7. Subsequently, check the position of the angle indicator. If necessary, loosen the pointer (19) using a Philips

screwdriver, set to position 0° on the angle scale (18)and re-tighten the retaining screw.

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Compound Mitre Saw – CM-210

Crosscut 90° and Turntable 0°

BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG BAUMR-AG

Baumr-AG CM-210 User manual

Popular Saw manuals by other brands