Bayco Products NIGHTSTICK X Series User manual

Permissible XPP-5410 Flashlight Assembly
APPROVAL No. 20-A140006-0
TESTED FOR INTRINSIC SAFETY IN METHANE-AIR MIXTURES ONLY
WARNINGS:
CLASS I DIV 1 GRPS A-D T3
CLASS II & III DIV 1 GRPS E-G T135C
CLASS I ZONE 0 AEx ia IIC T3 Ga
CLASS I ZONE 0 Ex ia IIC T3 Ga
Ex ia op is I Ma
Ex ia op is IIC T3 Ga
Intertek ITS 13 ATEX27839X
IECEx ITS 14.0036X
-20ºC ≤ Tamb ≤ +40ºC
1.5V/Cell AAA Alkaline
0359
ID 4001184
INTRINSICALLY SAFE
SECURITE INTRINSEQUE
I M 1 Ex ia op is I Ma
II 1 G Ex ia op is IIC T3 Ga
The Model XPP-5410 is MSHA approved for use with Energizer (Type E92),
two Energizer (Type EN92), and Duracell (Type MX2400), Duracell
(PC2400), and Duracell (EN92) batteries only. Replace the batteries in
fresh air only and replace all batteries at the same time. Do not mix
batteries from different manufacturers or of different types. The Model
XPP-5410 must not be opened in area where permissibility required.
Conforms to:
ANSI/UL STD 913, ANSI/UL
60079-0, ANSI/UL 60079-11
ANSI/ISA 60079-26
Certified to:
CAN/CSA STD C22.2 No 157
CAN/CSA STD C22.2 No 60079-0
CAN/CSA STD C22.2 No 60079-11
CSA STD C22.2 No 25
INMETRO
Segurança
NCC
Ex ia op is I Ma
Ex ia op is IIC T3 Ga
(-20ºC ≤ Tamb ≤ +40ºC)
15.0319 X
Instruction Manual
XPP-5410G
Please read these instructions before using your Nightstick XPP-5410G
Intrinsically Safe Penlight. They include important safety information and
operating instructions.
THE XPP-5410G IS APPROVED FOR USE
WARNINGS - INTRINSICALLY SAFE
yWarning: Use only the approved non-rechargeable batteries listed below.
yWarning: Do NOT attempt to use rechargeable AAA batteries with this
light.
yWarning: To prevent ignition of a hazardous atmosphere, do not open
the lens bezel in the hazardous environment. This task must ONLY be
performed in an area known to be non-hazardous.
yWarning: When exchanging batteries, use only ENERGIZER E92, EN92,
OR DURACELL MX2400, PC2400, EN92 BATTERIES.
yWarning: To prevent ignition of a hazardous atmosphere, the AAAbatteries
must only be exchanged in an area known to be non-hazardous.
yWarning: To reduce the risk of explosion, do not mix new non-rechargeable
batteries witha used non-rechargeable batteries, or mix non-rechargeable
batteries from different manufacturers.
yWarning: Substitution of components may impair intrinsic safety.
SPECIAL INSTRUCTIONS FOR INTRINSIC SAFETY
yFor personal safety, always conrm the rating of any known hazardous or
potentially hazardous location where the light is to be used.
BATTERY INSTALLATION
WARNING: In order to maintain the XPP-5410G’s Intrinsically Safe rating,
the only AAA batteries certied for use with this light are the ENERGIZER
E92, EN92, OR DURACELL MX2400, PC2400, EN92 BATTERIES.
yDo not attempt to use any other brand or model of AAA batteries with
this light.
yDo not attempt to use any type of rechargeable AAA batteries with
this light.
Warning: To prevent ignition of a hazardous atmosphere, do not remove
the lens bezel in the hazardous environment. This task must ONLY be
done in an area known to be non-hazardous.
yLoosen the locking screw located on the side of the lens bezel. NOTE:
Do NOT attempt to completely remove the locking screw. Doing so is not
necessary and may damage the threads. The screw simply needs to be
loosened enough to allow the lens bezel to unscrew.
yUnscrew the lens bezel from the housing in a counter-clockwise direction.
yUsing 2 – AAA ENERGIZER E92, EN92, OR DURACELL MX2400,
PC2400, EN92 BATTERIES (make sure both batteries are of the same
type), install the batteries in the light paying close attention to make sure
that the positive end of the batteries point toward the bezel end of the light.
yReplace the lens bezel by screwing it onto the housing in a clockwise
direction.
yTighten locking screw. CAUTION: Do NOT over-tighten. Doing so may
damage the threads and impact the light’s Intrinsic Safety.
OPERATION
THE XPP-5410G HAS TWO SEPARATE LIGHTING MODES:
MOMENTARY FLASHLIGHT MODE
Lightly press the tail switch for momentary operation. Release the switch
to turn the light off.
CONSTANT-ON FLASHLIGHT MODE
Press the tail switch until it clicks and then release for constant-on mode.
Press and release the tail switch again to turn the light off.

EU Declaration of Conformity (DoC)
XPP-5410G / XPP-5412G
Company name Bayco Products
Declare that the DoC is issued under our sole responsibility and belongs to the following product:
Apparatus model/Product: XPP-5410G/12G
Type: Flashlight
ATEX Directive 2014/34/EU
The following harmonised standards and technical specifications have been applied:
Evaluated to the following safety standards by Intertek:
EN 60079-0:2012/A11:2013 EN50303:2000 EN 60079-11:2012 (ia)
EN 60079-28:2015 (op is)
These Products are fully compliant and do not contain the restricted substances above levels noted in EU
RoHS.
Certificate No. ITS13ATEX27839X
Name James Conner
Engineer
Form F-900-001 Rev-A
Find more Bayco products on our website.Learn more about work lights we have.