BE QUIET! Shadow Rock User manual

The protective covering on the underneath of the cooler must
be removed prior to installation against the CPU.
Caution: The thermal past supplied is not suitable for human
consumption. If swallowed, drink lots of water and urgently
seek medical attention. Keep it out of the reach of children.
Avoid contact with skin and eyes.
Mounting the CPU cooler
Place the cooler mounting bridge (5) centrally on the cooler (1).
Insert from above the Intel/AMD mounting bridge fastening
screws (9) into the cooler mounting bridge (5). Next position
the cooler on the CPU. Then alternately tighten the Intel/AMD
mounting bridge fastening screws (9). For this you can use the
open-end wrench (14) or any cross-tip screwdriver.
Fitting and connecting the fan
Mount the 120mm fan (2) onto the cooler unit (1) using the
fan clips (12). Connect the fan to the CPU fan connector on
the motherboard.
When dismantling the 120mm fan (2), push the notches of the
fan clips (12) away from the fan.
Next position the cooler (1) on the CPU. Then alternately
tighten the Intel/AMD mounting bridge fastening screws (9).
For this you can use the open-end wrench (14) or any cross-tip
screwdriver.
Fitting and connecting the fan
Mount the 120mm fan (2) onto the cooler unit (1) using the
fan clips (12). Connect the fan to the CPU fan connector on
the motherboard.
When dismantling the 120mm fan (2), push the notches of
the fan clips (12) away from the fan.
Introduction: Thank you for deciding to purchase a be quiet!
product. The following instructions will guide you through the
installation process. If you do encounter installation problems,
please don't hesitate to contact our customer services by
mailing [email protected]. Please note that be quiet!
cannot accept liability for damage caused by compatibility
problems.
Warranty:
• 3-year manufacturer guarantee for consumers (original
purchase from authorized be quiet! dealers only)
• Guarantee work can only be processed with a copy
included of the purchase receipt from an authorized
be quiet! dealer
• Manipulation and structural changes of any kind, including
any damage caused by external mechanical force, will
lead to a complete voiding of the guarantee
• Our General Warranty Conditions apply, which can be
viewed on bequiet.com
Listan GmbH & Co.KG . Biedenkamp 3a . 21509 Glinde
Germany
For further information contact us via e-mail:
[email protected]
SCOPE OF DELIVERY
General
We recommend preparatory mounting of the
cooler outside the PC case for subsequent
installation.
The following parts are needed for this:
1x Shadow Rock LP CPU cooler (1), 1x 120mm fan (2), 2x Intel
mounting brackets (4), 1x cooler mounting bridge (5), 4x spacer
nuts (6), 4x mounting bracket fastening screws (8), 2x Intel/AMD
mounting bridge fastening screws (9), 2x fan clips (12), 1x open-
end wrench (14)
Assembly of the cooler mounting frame
Screw the spacer nuts (6) into the threads of the socket frame.
Place the Intel mounting brackets (4) onto the spacer nuts
and screw these tight with the mounting bracket fastening
screws (8).
The protective covering on the underneath of the cooler must
be removed prior to installation against the CPU.
Caution: The thermal past supplied is not suitable for human
consumption. If swallowed, drink lots of water and urgently
seek medical attention. Keep it out of the reach of children.
Avoid contact with skin and eyes.
Mounting the CPU cooler
Place the cooler mounting bridge (5) centrally on the cooler
(1). Insert from above the Intel/AMD mounting bridge fastening
screws (9) into the cooler mounting bridge.
Installation video
2011 square ILM
General
We recommend preparatory mounting of the
cooler outside the PC case for subsequent
installation.
The following parts are needed for this:
1x Shadow Rock LP CPU cooler (1), 1x 120mm fan (2), 1x
Intel backplate (3), 2x Intel mounting brackets (4), 1x cooler
mounting bridge (5), 4x Intel 775/115X/1366 nuts (7), 4x
mounting bracket fastening screws (8), 2x Intel/AMD mounting
bridge fastening screws (9), 4x Intel backplate screws (10), 4x
O-rings (11), 2x fan clips (12), 1x open-end wrench (14), Intel
LGA 775 backplate cap (15)
Mounting the backplate
Position the Intel backplate screws (10) in the notches situated
on the rear side of the Intel backplate (3). Pay attention in so
doing to align with the holes drilled for each socket. For fixing the
backplate screws onto the Intel backplate use the O-rings (11).
Once assembly of the Intel backplate (3) for the respective
Intel socket has been completed, position it under the
motherboard. In so doing make sure that the backplate screws
are precisely located within the motherboard holes.
Please note: When installing on a 775 socket, the Intel LGA
775 backplate cap (15) must be inserted into the middle of the
Intel backplate (3).
Assembly of the cooler mounting frame
Screw the Intel 775/115X/1366 nuts (7) onto the previously
positioned Intel backplate. Then position the Intel mounting
brackets (4) onto the Intel 775/115X/1366 nuts, in order to
then affix this with the mounting bracket fastening screws (8).
775
1150, 1151, 1155, 1156
1366
Intel LGA 2011 square ILM Intel LGA 775 / 1150 / 1151 / 1155 / 1156 / 1366
Glinde, 05/2018
Part name Quantity
be quiet! Shadow Rock LP
CPU cooler 1
120mm fan 1
Intel backplate 1
Intel mounting brackets 2
Cooler mounting bridge 1
Spacer nuts 4
Intel 775/115X/1366 nuts 4
Part name Quantity
Mounting bracket fastening
screws 4
Intel/AMD mounting bridge
fastening screws 2
Intel backplate screws 4
O-rings 4
Fan clips 2
AMD clips 2
Open-end wrench 1
Intel LGA 775 backplate cap 1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Installation video
1150, 1151,
1155, 1156
1366
775

Fitting and connecting the fan
Mount the 120mm fan (2) onto the cooler unit (1) using the fan
clips (12). Connect the fan to the CPU fan connector on the
motherboard.
When dismantling the 120mm fan (2), push the notches of the
fan clips (12) away from the fan.
General
We recommend preparatory mounting of the
cooler outside the PC case for subsequent
installation.
The following parts are needed for this:
1x Shadow Rock LP CPU cooler (1), 1x 120mm fan (2), 1x cooler
mounting bridge (5), 2x Intel/AMD mounting bridge fastening
screws (9), 2x fan clips (12), 2x AMD clips (13)
Assembly of the cooler mounting bridge
Screw the AMD clips (13) lightly onto the underside of the
cooler mounting bridge (5) with the Intel/AMD mounting bridge
fastening screws (9). Then place the cooler mounting bridge
centrally on the cooler (1).
Next assemble the opposite side as you did before. Be
sure to not completely tighten the screws; one or two turns
should suffice. The protective covering on the underneath
of the cooler must be removed prior to installation against
the CPU.
Caution: The thermal past supplied is not suitable for
human consumption. If swallowed, drink lots of water and
urgently seek medical attention. Keep it out of the reach of
children. Avoid contact with skin and eyes.
Mounting the CPU cooler
Next position the cooler over the CPU (1). Then press the
cooler mounting bridge (5) on one side of the retention module
until it hooks in. Repeat this procedure with the other side. You
can use any cross-tip screwdriver for this.
Next alternately tighten the Intel/AMD mounting bridge
fastening screws (9). It is important that the cooler unit is firmly
affixed to the motherboard.
AMD AM2(+) / AM3(+) / AM4 / FM1 / FM2(+)
Notes
bequiet.com
Installation video
Limited Warranty
As per the terms and conditions of this limited warranty as given
below, be quiet! warrants its new products to be free of defects
resulting from faulty materials and faulty manufacturing for the length
of the warranty period.
I. APPLICABILITY
This non-transferable warranty is applicable to newly purchased,
previously unopened be quiet! products and is enforceable by only
the original consumer purchaser. Proof of purchase is required for
warranty service, so should be retained. be quiet! does not provide
warranty registration services.
II. WARRANTY PERIOD
For eligible products, parts and labor are warranted for the appli-
cable warranty period from the date of purchase. The applicable
warranty period varies by product model, and is identied in your
user documentation, on the product package, or as listed below.
Should any of these warranty periods dier, the longest specied
warranty period will apply. Replaced products will be warranted
for the remainder of the original warranty period or thirty days,
whichever is longer.
III. EXCLUSIONS
The following are not covered by the warranty:
1. Normal wear and tear.
2. Any product which has been modied without permission from
be quiet!, or on which the serial number or warranty sticker has been
defaced, modied, or removed.
3. Damage, deterioration or malfunction resulting from:
Accident, abuse, misuse or improper use, neglect, connection to
an improper voltage source, unauthorized product modication, or
failure to follow instructions included with the product.
Fire, water, lightning, or other acts of nature.
Repair or attempted repair by anyone not authorized by be quiet!.
Shipping or transport damage (claims must be made with the carrier).
Any other cause which does not relate to a defect in materials or
manufacturing workmanship.
4. Cartons, cases, batteries, cabinets, tapes, accessories or other
consumables used with this product.
5. be quiet!, Inc. does not warrant that this product will meet your
requirements. It is your responsibility to determine the suitability of
this product for your purpose.
6. Removal or installation charges.
7. Shipping charges.
8. Any incidental charges.
IV. EXCLUSION OF DAMAGES
be quiet!‘s sole obligation and liability under this warranty is limited
to the repair or replacement of a defective product at its option.
be quiet! shall not, in any event, be liable for any special, incidental,
indirect, or consequential damages whatsoever, including but not
limited to loss of prots, revenue, or data (whether direct or indirect),
damages resulting from interruption of service and loss of business,
or for liability in tort relating to this product or resulting from its use
or possession, even if be quiet! has been advised previously of the
possibility of such damages.
V. LIMITATIONS OF IMPLIED WARRANTIES
There are no other warranties, expressed or implied, including but not
limited to those of merchantability or tness for a particular purpose.
The duration of implied warranties is limited to the warranty length
specied in Paragraph II.50
VI. LOCAL LAW AND YOUR WARRANTY
This warranty gives you specic legal rights. You may also have other
rights granted under local law. These rights may vary.
VII. NO OTHER WARRANTY
No be quiet! employee, dealer, or other agent is authorized to make
any modication, extension, or addition to this warranty.
VIII. TO OBTAIN TECHNICAL SUPPORT OR WARRANTY SERVICE
Please see your product owner’s manual or visit the service section
at www.bequiet.com for details and contact information. You will
need to provide proof of purchase for warranty service.
bequiet.com