Page 4 of 4 75.5172.06 PANTHER SERIES 20160517
FCC ID: 2ABWS-10TD900PTRI IC: 4680-10TD900PTRI
MODEL: 10EMR61-900 MODEL: 10EMR4751-900 MODEL: 10EMS4751-900
MODEL: 10EMR6-900 MODEL: 10EMR475-900 MODEL: 10EMS475-900
MODEL: 10EMR6L-900 MODEL: 10EMR475L-900 MODEL: 10EMS475L-900
Page 4 of 4 75.5172.06 PANTHER SERIES 20160517
Upon completion of the installation or service work, at a minimum, perform a daily safety check in accordance with the minimum
inspection guidelines provided by AAADM. Provide each equipment owner with an owner’s manual that includes a daily safety
checklist and contains, at a minimum, the information recommended by AAADM. Offer an information session with the equipment
owner explaining how to perform daily inspections and point out the location of power/operation switches to disable the equipment if
a compliance issue is noted. The equipment should be inspected annually in accordance with the minimum inspection guidelines. A
safety check that includes, at a minimum, the items listed on the safety information label must be performed during each service call.
If you are not an AAADM certifi ed inspector, BEA strongly recommends you have an AAADM certifi ed inspector perform an AAADM
inspection and place a valid inspection sticker below the safety information label prior to putting the equipment into operation.
ANSI / AAADM Compliance
TECHNICAL SPECIFICATIONS
Dimensions 6” ROUND - 6.33” diameter, 1.45” depth
4.75” ROUND - 5.12” diameter, 1.42” depth
4.75” SQUARE - 5.12” height, 5.12” width, 1.42” depth
Weight 6” ROUND - 1.2 lbs
4.75” ROUND - 1.14 lbs
4.75” SQUARE - 1.04 lbs
Material FACEPLATE - stainless steel
HOUSING - ABS plastic
Transmitter Frequency 433 MHz or 900 MHz
Power 900 MHz versions - two (2) CR2032
Mounting Surface mount only
Certification FCC, IC
Temperature 14 °F - 131 °F (-10 °C - 55 °C)
Enclosure Rating NEMA 4
Specifications are subject to change without prior notice.
All values measured in specific conditions.
PLEASE KEEP FOR FURTHER USE - DESIGNED FOR COLOR PRINTING
©BEA|OriginalInstructions|75.5172.06PANTHERSERIES20160517
T
ech
Support:
1-800-407-4545
|
Customer
Service:
1-800-523-2462
|
General
T
ech
Questions:
T
[email protected] |
T
ech
Docs:
www.beasensors.com
FCC / IC
“This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired operation.”
Changes or modifications not expressly approved by BEA Incorporated could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates,
uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the
interference at his own expense.
This device complies with Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two conditions: (1) this device may not cause
interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions
suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d’en compromettre le fonctionnement.
