BEA IXIO-DT1 User manual

IXIO-DT1
1
2
9
78
5
3
4
6
20.5349
75.5751.12 IXIO-DT1 20230913 Page 1 of 12
MOTION AND PRESENCE SENSOR FOR
AUTOMATIC SLIDING DOORS
ENGLISH
Visit website for
available languages of
this document.
1. cover
2. LED window
3. radar antenna
4. AIR curtain width adjustment
5. LCD
6. AIR lenses
7. AIR curtain angle adjustment knob
8. main adjustment knob
9. main connector
DESCRIPTION
This device can be expected to comply with Part 15 of the FCC Rules, provided it is assembled in exact accordance with the instructions
provided with this kit. Operation is subject to the following conditions: (1) this device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may cause undesired operation.
10ICA
Ceiling accessory
10CDA
Curved door accessory
10IMB
Bracket accessory
35.1609: black cover
35.1302: white cover
35.1303: silver cover
10URA
Universal rain accessory
10IXIOSPACER
Spacer
ACCESSORIES
Download the BEA DECODER app
for a quick overview of settings

Page 2 of 12 75.5751.12 IXIO-DT1 20230913
INSTALLATION
The sensor should
be mounted securely
to avoid extreme
vibrations.
Avoid highly reflective
objects in the infrared
field.
Avoid moving objects
and light sources in the
detection field.
Do not cover the sensor.
Only trained and
qualified personnel
are recommended for
installation and setup of
the sensor.
The warranty is invalid if
unauthorized repairs are
made or attempted by
unauthorized personnel.
Following installation,
always test for proper
operation (according
to ANSI 156.10) before
leaving the premises.
The door control unit
and the header cover
profile must be correctly
grounded.
SAFETY
It is recommended to clean
the optical parts at least once
a year or more if required due
to environmental conditions.
Do not use aggressive
products to clean
the optical parts.
MAINTENANCE
READ BEFORE BEGINNING INSTALLATION/PROGRAMMING/SETUP
BEA, Inc., the sensor manufacturer, cannot be held responsible for incorrect installations or incorrect adjustments of the sensor/device;
therefore, BEA, Inc. does not guarantee any use of the sensor/device outside of its intended purpose.
BEA, Inc. strongly recommends that installation and service technicians be AAADM-certified for pedestrian doors, IDA-certified for doors/
gates, and factory-trained for the type of door/gate system.
Installers and service personnel are responsible for executing a risk assessment following each installation/service performed, ensuring
that the sensor/device system performance is compliant with local, national, and international regulations, codes, and standards.
Once installation or service work is complete, a safety inspection of the door/gate shall be performed per the door/gate manufacturer’s
recommendations and/or per AAADM/ANSI/DASMA guidelines (where applicable) for best industry practices. Safety inspections must
be performed during each service call – examples of these safety inspections can be found on an AAADM safety information label (e.g.
ANSI/DASMA 102, ANSI/DASMA 107, UL294, UL325, and International Building Code).
Verify that all appropriate industry signage, warning labels, and placards are in place.
BEA, INC. INSTALLATION/SERVICE COMPLIANCE EXPECTATIONS

75.5751.12 IXIO-DT1 20230913 Page 3 of 12
TECHNOLOGY / PERFORMANCE
Detection mode: Motion
minimum detection speed: 2 in/s
Presence
typical response time: < 200 ms (max: 500 ms)
Technology: Microwave doppler radar
Transmitter frequency: 24.150 GHz
Transmitter radiated power: < 20 dBm EIRP
Transmitter power density: < 5 mW/cm2
Active infrared with background analysis
Spot: 2” × 2” (typ)
Number of spots: max. 24 per curtain
Number of curtains: 2
Mounting height: 6’6” – 11’6”
local regulations may impact acceptable mounting height (pedestrian applications only)
Sensor temperature
range:
-13 – 131 °F *
0 – 95% relative humidity, non-condensing
LCD screen is operational from 14 – 131 °F.
The sensor may still be programmed in colder temperatures, but with the remote control.
ELECTRICAL
Output
Relay 1 Electromechanical relay (potential and polarity free)
Max. contact current: 1 A
Max. contact voltage: 30 VAC
Adjustable hold time: 0.5 – 9 s
Relay 2 Solid-state relay (potential and polarity free)
Max. contact current: 100 mA
Max. contact voltage: 42 VDC / 30 VAC
Test/Monitoring
input:
Sensitivity:
Low: < 1 V
High: > 10 V (max. 30 V)
Response time on test request: typical < 5 ms
Supply voltage: 12 – 24 VAC ±10%
12 – 30 VDC ±10%
to be operated from SELV-compatible power supplies only
Power consumption: < 2.5 W
Noise: < 70 dB
PHYSICAL
Degree of protection: IP54
COMPLIANCE
FCC certification: FCC: G9B-100606
IC: 4680A-100606
Compliance: ISO 13849 PL «c» CAT. 2
(under the condition that the door control system monitors the sensor at least once per door cycle)
TECHNICAL SPECIFICATIONS
Specifications are subject to change without prior notice.
All values measured in specific conditions.

...
Page 4 of 12 75.5751.12 IXIO-DT1 20230913
To adjust contrast, push and turn
the grey button simultaneously.
During normal function only.
Negative display = active output
= scroll = select
3) Select language before entering the first LCD menu.
During the first 30 seconds after power-on of the
sensor or later in the diagnostics menu.
Select Back to
return to previous
menu or display.
Select More to go to next level:
- basic settings (MENU 1)
- advanced settings (MENU 2)
- diagnostics (MENU 3)
1) Push to enter the LCD menu.
1) Navigate to menu 3 (Diagnostics). 2) Select "ZIP code". 3) Change the code as desired.
displayed value
=
factory value
displayed value
=
saved value
Activation
impulse
Safety
2) Enter password, if necessary.
Not during the first minute after
power-on of the sensor.
Password
XX X X
ZIP code
V
To activate the new ZIP code, you must validate the last digit (see below):
v = valid ZIP code (values will be changed accordingly)
x = invalid ZIP code (no values will be changed)
v/x = valid ZIP code, but from a different product
*only available values
will be changed*
ZIP code
H24 1 56-KG4
01 0 800/02F
ZIP code
ID #
ZIP code
E24 1 56-KG4
01 0 800/02F
ZIP code
E24 1 56-KG4
01 0 800/02F
ZIP code
E24 1 56-KG4
01 0 800/02F
ZIP code
H24 1 56-KG4
01 0 800/02F
HOW TO USE THE LCD
DISPLAY DURING NORMAL FUNCTION
FACTORY VALUE VS. SAVED VALUE
NAVIGATING IN MENUS
CHANGING A ZIP CODE
VALUE CHECK WITH REMOTE CONTROL
See application note on ZIP CODE (76.0024).
Pressing a parameter symbol on your remote control displays the saved value
directly on the LCD screen. Additionally, the green LED will blink the number
of times that the parameter is set to. Do not unlock first.
Note: When querying FIELD SHAPE, the green LED will blink the number of
times that it is set to, and then the green LED will blink either 1 time (narrow
shape) or 2 times (wide shape).

1
75.5751.12 IXIO-DT1 20230913 Page 5 of 12
* The sensor LED will briefly flash RED during monitoring communication with door control, indicating that
external monitoring is functional. Monitoring functionality must be active on the sensor, door control, and
monitoring wires must be properly connected to the door control.
Mounting is compatible with the WIZARD.
Using the provided mounting template, mount the sensor, ensuring that the bottom of the sensor is
within 2 inches of the bottom of the door header.
Refer to Application Note 76.0035 if an IXIO Spacer is required for the given application.
Route the harness (20.5349) using the harness clip as shown in the exploded view of the mounting
illustration.
MOUNTING
RED
SENSOR
DOOR CONTROL
BLACK
BROWN
BLUE
WHITE (COM)
YELLOW (N.C)
GREEN (N.O.)
PURPLE
PURPLE
POWER SUPPLY
POWER SUPPLY
SAFETY INPUT
SAFETY INPUT
TEST OUTPUT*
TEST OUTPUT*
OPENING INPUT
OPENING INPUT
OPENING INPUT
Sensor connectivity (power and relays) must utilize only the supplied harness.
Sensor power must be supplied from a Class 2 supply source limited to 15 W.
Sensor is intended to be monitored for proper operation by the door operator or system.
Harness shall be routed separated from any Mains or non-Class 2 voltage cable for correct operation or shall be rated for the Mains
voltage, and suitable protection and routing means shall be used according to National and Local Codes to prevent damage to the
harness and/or IXIO sensor.
WIRING
max. 2 in
MOUNTING & WIRING
VOLTAGE
Power: 12 – 24 VAC, 50/60 Hz
12 – 30 VDC
2.5 W (max)
Test: low: < 1 V
high: > 10 V (30 V max.)
response time: typ. < 5 ms

2
Page 6 of 12 75.5751.12 IXIO-DT1 20230913
RADAR OPENING IMPULSE FIELD
ANGLE
field size: 9
immunity: 2
field size: 9
immunity: 2
The size of the detection field varies according to the mounting height of the sensor.
The following graphics are representations – not default settings.
from 15° to 45°, default 30 °
from -15° to 15°, default 0°
WIDTH
field size: 9
immunity: 2
field size: 9
immunity: 2
13’ x 6’6" (wide)
6’6" x 8’ (narrow)
1 × 1 grid is approximately 3.28 ft × 3.28 ft.
7.2 ft
7.2 ft
7.2 ft
7.2 ft
or
or
green LED = motion
detection

C1
C2
3
x2
75.5751.12 IXIO-DT1 20230913 Page 7 of 12
INFRARED SAFETY FIELD
If necessary, adjust the AIR curtain angle
(from -7° to 4°, default 0°).
Activate the visible spots to verify the position of the AIR curtain.
Visibility depends on external conditions. When spots are not visible, use
the Spotfinder to locate the curtains.
ANGLE
DOOR
max. 3 in
The distance between the inner curtain of the inside
door sensor and the inner curtain of the outside
door sensor should always be smaller than 8 in.
C1 = closest to sliding door
C2 = farthest from sliding door
Part of the detection field can be masked to reduce its width. The arrow position determines the width of the detection field.
The size of the detection field varies according to the mounting height and the settings of the sensor.
Wide setting has 1:1 ratio. For example, a 6-foot mounting height will project a 6-foot detection width at floor.
WIDTH
Always verify the actual detection field width by walk-testing according to ANSI 156.10.
Additional adjustments are possible by LCD or remote control
(see OVERVIEW OF SETTINGS).
OR
CLOSERCLOSER
AWAYAWAY
x2
red LED = presence
detection
green LED = motion
detection

+
+
+
2 s
4 s
4
Page 8 of 12 75.5751.12 IXIO-DT1 20230913
BASICADVANCEDDIAGNOSTICSDIAGNOSTICS
SETUP
Set up the sensor using either push-buttons or the remote control.
TEST THE PROPER OPERATION OF THE INSTALLATION BEFORE LEAVING THE PREMISES!
SETUP 1 QUICK
SETUP 2 ASSISTED
test of full door cycle + reference picture
either hold the knob for 2 seconds, or use the remote
control buttons as specified
either hold the knob for 4 seconds, or use the remote
control buttons as specified
STEP OUT OF THE INFRARED FIELD!
LED flashes red-green

+
+
0 987654321
75.5751.12 IXIO-DT1 20230913 Page 9 of 12
all parameter settings in zipped format (see application note on ZIP CODE –76.0024)
unique ID-number
last 10 errors + day indication
view of spot(s) that trigger detection
signal amplitude received on curtain
signal amplitude received on curtain 2
supply voltage at power connector
power duration since first startup
OVERVIEW OF SETTINGS
Back
Back
Back
More
More
More
More
Back
RAD: FIELDSIZE
RAD: SHAPE
RAD: FIELDSIZE
RAD: IMMUNITY
RAD: DIRECTION
RAD: HOLDTIME
RAD: REENTRY
RAD: OUTPUT
AIR: WIDTH
AIR: OUTPUT
TEST
BASICADVANCEDDIAGNOSTICS
factory value
RC BUTTONS
see note 1
see note 2
see note 3
see note 4
see note 2
see note 2
see note 3
see note 5
see note 6
see note 1
small
small
small
0.5 s
>
>
>
8 s
highlow
large
LCD: "narrow" and "wide" setting options (default = wide)
Remote Control: = wide, = narrow
large
large
9 s
>
>
> >
6 s
>
>
>
7 s
>
>
>
>
5 s
>
>
>
>
4 s
>
>
>
>
3 s
>
>
>
>
1 s
>
>
>
>
2 s
>
MTFunioff bi
onoff
AIR: IMMUNITY
AIR: WIDTH
AIR: NUMBER
AIR: FREQ
AIR: OUTPUT
TEST
REDIRECTION
FACTORY RESET
AIR: PRESENCE TIME
ZIP CODE
ID #
CONFIG P/N
SOFT P/N
ERROR LOG
AIR: SPOTVIEW
AIR: C1 ENERG
AIR: C2 ENERG
POWERSUPPLY
OPERATINGTIME
RESET LOG
PASSWORD
ADMIN
delete all saved errors
LCD and remote control password (0000= no password)
enter code to access admin mode
normal
60 min
full
reset
infinte
partial
reset
10 min
mode B
20 min5 min2 min1 min
enhanced
1
A
30 s
2
B
on
R1 MW or IR
R2 IR
off
R1 MW
R2 IR
DeEner/NO
NC
DeEner/NO
NC
DeEner/NO
NC
Energ/NC
NC
Energ/NC
NC
Energ/NC
NC
Energ/NC
NO
Energ/NC
NO
Energ/NC
NO
DeEner/NO
NO
DeEner/NO
NO
DeEner/NO
NO
DIAGNOSTICS
(green)
motion
(red)
presence
uni +
reentry

Page 10 of 12 75.5751.12 IXIO-DT1 20230913
OVERVIEW OF SETTINGS (cont.)
NOTES
Note 1 Always use a screwdriver when making further AIR adjustments to the arrow position on the
sensor.
Note 2 RADAR AIR
NO = normally open
NC = normally closed
DeEner = de-energized relay (active)
Energ = energized relay (passive)
NO = normally open
NC = normally closed
Note 3 The sensor LED will briefly flash RED during monitoring communication with door control. This
indicates that external monitoring is functional.
Monitoring functionality must be active on the sensor and door control, and monitoring wires
must be properly connected to the door control.
Note 4 MTF = uni-directional with motion-tracking feature
uni + reentry: BEA recommends only adjusting using the LCD
Note 5 REDIRECTION setting (F1 on remote control):
R1-MW, R2-IR (F1=0):
R1 = MW (i.e. motion detection)
R2 = IR (i.e. presence detection)
R1-MW or IR, R2-IR (F1=1):
R1 = MW or IR (i.e. motion or presence detection)
R2 = IR (i.e. presence detection)
Note 6 partial: outputs are not reset