BEA FALCON User manual

FALCON/FALCONXL
1
2
5
6
4
3
Specications are subject to changes without prior notice.
*
Other use of the device is outside the permitted purpose and can not be guaranteed by the manufacturer.
*
* Measure
d
in o
p
tima
l
con
d
itions
TECHNICAL SPECIFICATIONS
DESCRIPTION
ENGLISH
Openingsensorforautomaticindustrialdoors*
1. push buttons
2. front face
3. radar antenna
4. angle indication
5. bracket
6. cable
Technology:
Transmitter frequency:
Transmitter radiated power:
Transmitter power density:
Detection mode:
Detection zone:
Min. detection speed:
Supply voltage:
Mains frequency:
Max power consumption:
Output:
Max. contact voltage:
Max. contact current:
Max. switching power:
LED-signal:
Mounting height:
Degree of protection:
Temperature range:
Dimensions:
Tilt angles:
Materials:
Weight:
Cable lenght:
Norm conformity:
microwave
24.150 GHz
< 20 dBm EIRP
< 5 mW/cm²
motion
FALCON: 4 x 5 m ; FALCON XL: 4 x 2 m (typical at 30° and eld size 9)
5 cm/s**
12V to 24V AC ±10%; 12V to 24V DC +30% / -10%
50 to 60 Hz
< 2 W
relay (free of potential change-over contact)
42V AC/DC
1A (resistive)
30W (DC) / 60VA (AC)
red: detection state, parameter indication; green: value indication
FALCON: 3.5 m - 7m; FALCON XL: 2 m - 3.5 m
IP65
from -30 °C to + 60 °C
127 mm (L) x 102 mm (H) x 96 mm (W)
0° to 180° vertical
ABS and polycarbonate
400 g
10 m
R&TTE 1999/5/EC; EMC 2004/108/EC
FALCON:fornormaltohighmounting(3.5-7m)
FALCON XL: for low mounting (2 - 3.5 m)
BEA SA | LIEGE Science Park | ALLÉE DES NOISETIERS 5 - 4031 ANGLEUR [BELGIUM] | T [phone] | F [phone] | [email protected] | WWW.BEA.BE
1
1
2
3
4
5
1
2
1
2
1
1
2
3
1
1
2
3
|
Ori
g
ina
l
instruction
s
|
42.7330
/
V
1
-
0
9
.
1
0
BEA hereby declares that the FALCON is in conformity with the basic requirements and the other
relevant provisions of the directives 1999/5/EC and 2004/108/EC.
TROUBLESHOOTING
The sensor power is o. Check the wiring and the power supply.
Angleur, August 2010 Jean-Pierre Valkenberg, Authorized representative
The complete declaration of conformity is available on our website: www.bea.be
The door opens
and closes
constantly.
The LED
ashes quickly
after unlocking.
The sensor does
not respond to the
remote control.
Improper output
conguration on the sensor.
The sensor is disturbed
by the door motion or
vibrations caused by the
door motion.
The sensor needs an access
code to unlock.
Batteries in the remote
control are weak or
improperly installed.
Check the output conguration setting on each
sensor connected to the door operator.
Check and change the batteries if necessary.
Make sure the detection mode is unidirectional.
Increase the detection lter.
ACCESS CODE
SAVING AN ACCESS CODE:
DELETING AN ACCESS CODE:
The access code (1 to 4 digits) is recommended to set sensors installed close to each other.
Once you have saved an access code, you always need to enter this code to unlock the sensor.
If you do not know the access code, cut and restore the power supply. During 1 minute, you can access the sensor
without introducing any access code.
The door remains
closed.
The LED is OFF.
The door does not
react as expected.
Make sure the sensor is xed properly.
Make sure the detection mode is unidirectional.
Increase the tilt angle.
Increase the detection lter.
Reduce the eld size.
Enter the right access code.
If you do not know the access code, cut and
restore the power supply to access the sensor and
change or delete the access code.
Change the antenna angle.
Decrease the eld size.
Increase the detection lter.
The door opens for
no apparent reason.
The sensor detects the
motion of the rain drops or
vibrations.
In highly reective
environments, the sensor
detects objects outside of its
detection eld.
Only for EC countries: According the European Guideline 2002/96/EC for Waste Electrical and Electronic Equipment (WEEE)
SAFETY INSTRUCTIONS
The manufacturer of the door system is responsible for carrying out a risk assessment and installing the sensor and the door system in compliance with
applicable national and international regulations and standards on door safety.
Only trained and qualied personnel may install and set-up the sensor.
The warranty is void if unauthorized repairs are made or attempted by unauthorized personnel.
The vehicle detection
lter is used, but
pedestrians are still
detected.
The chosen value is not
optimal for this application. Increase the detection lter.
Decrease the sensor angle.
Increase the installation height.

XXSXSS>>>>LXLXXL
0.5 s 1 s 2 s 3 s 4 s 5 s 6 s 7 s 8 s 9 s
3456
12
P
A
(7)
(0)
(1)
(2)
(1)
FALCON
bi uni
POSSIBLE SETTINGS BY REMOTE CONTROL
FIELD SIZE
OUTPUT
CONFIGURATION
A = active output (relay active when detection)
P = passive output (relay active when no detection)
DETECTION MODE uni
AWAY
FACTORY VALUES RESETTING TO FACTORY VALUES:
Avoid proximity to neon
lamps or moving objects.
Do not cover the sensor.
DETECTION FILTER
HOLDOPEN TIME
Avoid vibrations. Only open the sensor
when the cable needs
to be replaced.
Wall mounting Ceiling mounting Bracket dimensions
TO START OR END AN ADJUSTMENT SESSION, press and hold either push button until the LED ashes or
stops ashing.
1 FIELD SIZE
Parameter n°
2 HOLD-OPEN TIME
3 OUTPUT CONFIGURATION
4 DETECTION MODE
5 DETECTION FILTER
Value (factory values)
TO SCROLL THROUGH THE
PARAMETERS, press
the right push button.
TO CHANGE THE VALUE OF
THE CHOSEN PARAMETER,
press the left push button.
TO RESET TO FACTORY VALUES, press and hold both push buttons until both LEDs ash.
POSSIBLE SETTINGS BY PUSH BUTTONS
MOUNTING TIPS
DIMENSIONS (in mm)
bi = two-way detection
uni = one-way detection towards sensor
uni AWAY = one-way detection away from sensor
1
12 3
2
COM
NO
NC
GN
BN
WH
YE
GY
12-24 V
AC-DC
12
2
3
0-9
1-6
FALCON
15°
30°
45°
+45°
7 m 5 m 3.5 m 2.5 m
3 3 3 3
4 4 4 4
5 5 5 4
6 6 6 5
XL
Position the sensor on the
bracket and fasten the screws
rmly.
FALCON
Mounting height: 5 m FALCON
Mounting height: 3.5 m
FALCON XL
Mounting height: 2.5 m
MOUNTING & WIRING
Adjust the angle of the sensor to position the detection eld.
Remove the bracket
from the sensor.
Drill 2 holes accordingly.
Fix the bracket rmly.
Connect the wires to the door
controller. Choose between NO
and NC contact.
DETECTION FIELD ADJUSTMENTS
DETECTION FILTER
Adjust the eld size by remote
control or push buttons.
All detection eld dimensions were measured in optimal conditions and with eld size value 9.
CEILING
WALL
Choose the right detection lter for your application by remote control or push button:
Value recommendations according to angle and height:
Detection of all targets
(pedestrians and parallel trac are detected°
1 = no specic lter
2 = lter against disturbances
(recommended in case of vibrations, rain etc.)
Detection of just vehicles moving towards the sensor*
(pedestrians and parallel trac are not detected + lter against disturbances)
* The vehicle detection lter increases the response time of the sensor.
Always check if the chosen
value is optimal for the
application.
Theobject sizeandmaterial
caninuencethedetection.