Beamshot BR100 User manual

Congratulations on purchasing your BR100 Laser Bird Repellent Devices. BR100
is designed to repel and clear birds at the distance of 100 meters to 1000 meters
depending on ambience light condition. With easy operation and carry handheld
size, built-in microchip to control two operation mode - momentary and strobe with
clear indicators, BR100 can repel and clear birds in minutes. Made of
aircraft-grade aluminum alloy with robust designed and scratch-free hard anodized
finish, BR100 is a water proof product and it can work under all weather and
temperature environments. Using state of art high power direct green laser diode
technology, not DPSS laser (Diode-Pumped Solid-State Laser), they have broad
operating temperature range from -40°F to 149°F (-40°C to 65°C) and 10,000
hours life time. BR100 consumes much less power consumption than DPSS laser
to ensure longer battery-operating time and minimum operation cost.
FEATURES
CONSTRUCTION
Battery Installation
SPECIFICATIONS
Laser Bird Repellent Tool - BR100
1. Repel and clear birds from long range in minutes.
2. With easy operation and carry handheld size, it uses microchip to
control two operation mode - momentary and strobe with clear indicators.
3. Using state of art high power direct green laser diode, it has broad
operating temperature range from -40°F to +149°F (-40°C to +65°C)
with 10,000 hours life time.
4. Made of aircraft-grade aluminum alloy with robust designed and
scratch-free hard anodized finish, it is a water proof product and it can
work under all weather and temperature environments.
5. Low power consumption, longer product life time and wider operation
temperature range compare to all others which are made from DPSS
green laser.
6. Use at: Airport, Agriculture, Poultry farming, Fishing farming, Golf
course, Stadium, Solar Power Plant, Recycling plants, Factory, Building.
Unscrew battery cap, insert two CR123A batteries, positive pole face
outside as Fig. 4-1.
After the battery is installed, screw battery cap and please make sure
keylock switch is at “OFF” position.
*Note*:
BR100 can be powered by two CR123A lithium batteries or one 18650
rechargeable battery. Please be noted 18650 rechargeable battery isn’t
included in the package. Recommend buying well known brand with high
quality 18650 battery if you like to use rechargeable battery. Please
remove batteries from BR100 whenever storage.
Fig. 4-1
Also at: Stadium, Recycling plants, Factory, Building…etc.
Airport Agriculture
Poultry farming Fishing farming
Solar power plant Golf course
Weight
230g±15 g
Dimensions
195(L) x 37(W) x 41(H) mm
Laser Wavelength
520±10 nm(Green Laser Diode)
Output Power
100mW (Class IIIb)
Construcon
Aluminum 6061 T6 with scratch-free hard
anodized nish.
Range (Day Time )
100 meters to 1000 meters
Range (Night Time)
Above 10 KM
Operaon
ON/OFF buon
Operang Temperature
-40°F ~ 149°F (-40°C ~ +65°C)
Water Proof
IP67
Baery
2 x CR123A baeries (included) or
1 x 18650 rechargeable baery (not included)
4
5167
2
3
Front side Back side
No.
Descripon
1
Laser Point Aperture
2
Front cap
3
ON/OFF buon
4
Ready Indicator
5
Laser on Indicator
6
Keylock switch
7
Baery Cap

SAFETY PRECAUTIONS
• Front cap and keylock switch are two protection devices to prevent laser
to fire accidentally. Please always close front cap and lock the keylock switch
after use. Please read user manual carefully before operation.
• When not in use, always keep the power on OFF mode, Including when in storage.
• Battery : The BR100 is powered two CR123A Lithium batteries (included) or
one 18650 rechargeable battery(not included).
• Do not allow water to enter the housing by keeping the battery cap shut.
• Do not store the BR100 with battery installed.
• Do not install a defective battery in the BR100.
• Prior to operating, check to see all batteries for cracks, bulging, and leakage.
• Do not puncture, disassemble, short circuit.
• Do not allow water to enter the housing by keeping the battery cap shut.
• When not in use, always keep the power on OFF mode, Including when
in storage.
• Do not store the BR100 with battery installed.
1. Make sure the BR100 is on Power OFF status.
2. Remove the battery and close the battery cap.
3. Clean BR100 with a soft cloth.
4. Wipe laser-emitting apertures with a dry lens cleaning tissue. Brush off
all loose dirt from the apertures carefully.
5. Wipe dust and dirt from all components with a soft dry cloth.
DANGER
DANGER
CAUTION
CAUTION
Table S-1:Nominal Ocular Hazard Distances (NOHD) of BR100
Exposure to the laser beam inside the NOHD minimum safe
range can cause permanent damage to the human eye.
• CLASS IIIb LASER PRODUCT.
• Laser radiation when open.
AVOID DIRECT EYE EXPOSURE.
• Use of controls or adjustments, or performance of procedures other
than those specified herein may result in hazardous radiation exposure.
• This laser product is classified as Class IIIb for Visible point according
to 21 CFR 1040.
• BR100 is Class IIIb Product and it can injure the eyes. Always avoid
BR100 to point at anyone at any time.
• Do not direct the laser beam at anyone operating a boat, vehicle or aircraft.
• Avoid all eye contact. Never look directly into the laser lens even if the laser
is off.
• Do not stare into the laser beams and laser aperture.
• Do not look into the laser beam through binoculars or telescopes.
• Do not point the laser beam at reflective surfaces.
• Never aim the laser beam at people’s eyes.
• This unit must be used by experienced technical personnel only.
• Do not leave the laser beam unattended.
• Do not target vehicles or aircraft with the laser beam when the unit is used outdoors.
• Do not look directly into laser beam with optical instrumentation unless
adequate protective filters are used to protect the eyes.
• Avoid aiming the laser beam at mirror- likes surfaces. Remove any
unnecessary mirror-likes surface from the vicinity of the laser beam path.
• The warranty will no longer exist once the product been taken apart.
Green Laser Point
Class
Class IIIb
NOHD(m)
148.41
NOHD(5-cm aided)(m)
1244.37
NOHD(8-cm aided)(m)
2009.00
NOHD(12-cm aided)(m)
3028.50
CONTENTS OF A SET
Normal Operation
BASIC MAINTENANCE
Ready Indicator
Laser on Indicator
Fig. 4-2
LED Indicator
LED Color
Status
Ready Indicator
Green
Laser is ready
Red
Low baery
Laser on Indicator
Red
Laser is eming
Red Strobe
On strobe mode
Laser Emission
Aperture
Laser Emission Direction
1. Unlock keylock switch, the “READY” Indicator will show green light.
2
.Open front cap.
3
.Press ON/OFF Buon Switch, Laser will be turned on. Release it and
the laser will be o.
4
.
5.
Double tap on ON/OFF Buon Switch and hold, Laser will be strobing.
Whenever Laser is on, release
Buon Switch, Laser will be o.
*Note*


Please be noted, BR100 is Class IIIb Laser Product and it can injure
the eyes. Always avoid BR100 to point at anyone at any me.
Do not direct the laser beam at anyone operang a boat, vehicle or
aircra.
No. Part Name QTY
Parts Stock
Number(PSN)
1
BR100
1
157-BR001G
2
CR123
2
451-C0103G
3
Key
2
410-BR001G
4
Lens cloth
1
499-5B108G
1
3 4
2
LED Status Indicator