Beamz PROBEAM7R User manual

User Manual
PROBEAM7R
7R 230W Beam Moving Head

1.1 Unpacking
1.2 Safety Instructions
Carefully unpack the carton, check the contents to ensure that all parts are present,
and have been received in good condition. Contact your supplier immediately and
retain packing material for inspection if any part is missing or damaged.
1. INTRODUCTION
■1 x PROBEAM7R
■1 x Power Cord
■2 x Mounting Brackets
■1 x User Manual
▪The product is for indoor use only.
▪Always turn off, unplug power and allow fixture to cool before servicing.
▪Ensure that fixture is properly grounded.
▪Please keep this User Guide for future consultation.
▪Always make sure that you are connecting to the proper voltage and that the line
voltage you are connecting to is not higher than that stated on decal or rear panel of
the fixture.
▪Always disconnect from power before servicing or replacing fuse.
▪Make sure power cord is never crimped or damaged.
!
Warning!!! To reduce the risk of fire, electric shock, or injury to persons,
follow these important safety instructions:
The following items are included in the box:
1
Thank you for selecting this product. The Moving Beam 7R is a beam moving head
with OSRAM lamp. It produces stunning beam effects, ideal for stages, conernts, TV
studios, live shows, night clubs, etc. To optimize the performance of this product,
please read the user manual carefully before use.
Caution! The electric connection must be carried
out only by a qualified electrician.
Caution! Never look directly into the light source, as
sensitive persons may suffer an epileptic shock.
Caution! Never touch the device during operation!
The housing may heat up.

2
The Moving Head is fully operational in any mounting position, hanging upside-down,
side mounted, or set on a flat llevel surface, etc.
1.3 Technical Data
1.4 Product overview
2. SETUP
2.1 Mounting
▪Power supply: AC 100-240V 50-60Hz
▪Power consumption: 350W
▪Lamp: OSRAM 7R 230W lamp, 8,000K, 2,000 hrs
▪Beam angle: 0-4° adjustable
▪1 Colour wheel: 14 COLOURs + white
▪1 Gobo wheel: 17 fixed gobos + open
▪Colour rainbow + Gobo shaking
▪8-facet rotating prism
▪Motorized focus
▪Frost-filter
▪DMX-controlled or stand-alone with master/slave
▪2 DMX modes: 16ch (Simple)/20ch (Expand)
▪Pan : 540° (16 bit) Tilt: 270° (16 bit)
▪Automatic Pan/Tilt correction
▪Mechanical shutter and adjustable speed strobe effect
▪Touch LCD display with Joy Wheel
▪Dimension: 523×337×511mm
▪Weight: 19.5 kg
IMPORTANT!!! Safety cables must
always be used when unit is celling
or truss mounted. The safety cable
must be capable of holding 10
times the weight of the fixture. The
equipment must be installed by
professionals.
When installing the device, make sure there is no highly-inflammable
material (decoration articles, etc.) within a distance of min. 0.5 m.
DANGER OF FIRE!
DMX In/Out Power On/Off Power In/Out
Fuse
LCD Display Joy Wheel

3
The fixture is designed to work on AC 100-240V 50-60Hz. All units must be powered
directly from a switched circuit. This unit cannot be run on a rheostat or dimmer
circuit even if used solely for a 0% to 100% switching.
You can link the Moving Head 7R to a DMX controller using a 3- or 5-pin DMX cable.
2.3 AC Power
2.4 DMX Linking
WARNING!!! All fixtures must be connected to circuits with a
suitable Earth Ground.
Wire
Brown
Blue
Yellow/Green
Pin
Live
Neutral
International
L
N
Earth
The occupation of connection-wire is as follows:
DMX CONTROLLER
DMX OutDMX In
It is recommended to use a DMX terminator for installations where the DMX cable
has to run a long distance, or is in an electrically noisy environment. The DMX
terminator is simply an XLR plug with a 120 Ωresistor connected between pins 2 and
3,which is then plugged into the output XLR socket of the last fixture in the chain.
Please see illustrations below.
1
2
3
PIN 3
PIN 2
120Ω

4
3.1 Control panel
3.2 Menu Map
3. OPERATION INSTRUCTIONS
DmxSet
Dmx Set set DMX address001-512
Dmx Channle 16CH/20CH
Dmx Signal KEEP/CLEAR
RDM Function ON/OFF
Dmx Monitor to read DMX values
Setup
RunMode
Language English
ScreenRotation OFF/ON
Display OFF(off in 30s)/ON (always on)
Invert Pan ON/OFF
ON/OFF
ON/OFF
Invert Tilt
Pan-Tilt swap OFF/ON
Pan-Tilt Encoder ON/OFF (setPan/Tillt correction)
Linear color
Load default to set factory defaults
DMX/AUTO/SOUNDAuto Mode
Manual Control Color,Shutter,Dimmer, Gobo,etc
Device Reset OK/Cancel
OK/Cancel
OK/Cancel
XY Reset
MT Reset
DMX Indicator Joy Wheel
DMX Channel modeDMX address
Error Indicator Press to enter/confirm
value,rotate to scroll through
menu list or change value.

5
System
Version Version number
Temp Msg Temperature information
Fan Msg Fan information
System Time Lamp/Fixture time
Sensor Monitor Pan/Tilt/Color/Gobo Hall
Lamp
Factory
System Error to show error info
Lamp ON/Off
Lamp On ON/OFF
Delay Time(Min) 00-19
ON/OFFLamp_Fan_Low
(password：
Up-Down-Up-Down）
Pan/Tilt/Color/Gobo motorMotor calibration
Range calibration Pan/Tilt/Focus/Dimmer Range
XY Sp calibration to set Pan/Tilt speed
Fan sp calibration to set fan speed
OK/CANCELLamp_hours_clear

6
3.2 DMX channels
PAN/TILT
MODE
SIMPLE
16CH
EXPAND
20CH
NAME DMX VALUECH
1
2
COLOUR
STROBE
select COLOURs, see details in COLOUR table
select strobe effects, see details in DIMMER & STROBE table
3 DIMMER select strobe effects, see details in DIMMER & STROBE table
4 GOBO select gobo, see details in GOBO table
5 PRISM select prism effect, see details in EFFECT table
6 PRISM ROTATION select prism rotation, see details in EFFECT table
7 NONE
8 FROST select frost effect, see details in EFFECT table
9 FOCUS focus adjustment from far to near
10 PAN Pan movement, see details in Pan/Tilt Table
11 PAN FINE
12 TILT Tilt movement, see details in Pan/Tilt Table
13 TILT FINE Fine control of Tilt, see details in Pan/Tilt Table
Fine control of Pan, see details in Pan/Tilt Table
14 P/T SPEED set Pan/Tilt movement speed, see details in Pan/Tilt Table
15 RESET reset the moving head, see details in Reset & Lamp Table
turn lamp on/off, see details in Reset & Lamp Table16 LAMP
17 GOBO SPEED set gobo wheel speed, see details in EXPAND CHANNEL Table
18 COLOUR SPEED set COLOUR wheel speed, see details in EXPAND CHANNEL Table
19 FOCUS SPEED set focus speed, see details in EXPAND CHANNEL Table
20 RUN MODE set running mode, see details in EXPAND CHANNEL Table
NAME FUNCTIONSCH
10 PAN
VALUE
0-255
0-255
0-255
0-255
0-255
0 - 540°
0 - 270°
11 PAN FINE
12 TILT
13 TILT FINE Fine control of Tilt movement
Fine control of Pan movement
14 P/T SPEED Pan/Tilt speed from fast to slow
DIMMER & STROBE
NAME FUNCTIONSCH VALUE
0-3
4-103
104-107
108-207
Strobe close
Strobe open
208-212 Strobe open
Strobe open
213-225 Random strobe, slow
226-238 Random strobe, medium
239-251 Random strobe, fast
252-255
strobe from slow to fast(mode 2)
strobe from slow to fast(mode 1)
2 STROBE
0-2553 DIMMER Dimmer 0 - 100%
The moving head can be operated in 2 DMX modes: SIMPLE (16ch) or EXPAND (20ch).

7
NAME FUNCTIONSCH VALUE
0-4
5-9
10-14
15-19
20-24
White
Colour 1
Colour 2
Colour 1 + Colour 2
White + Colour 1
25-29
30-34
35-39
40-44
Colour 3
Colour 4
Colour 3 + Colour 4
Colour 2 + Colour 3
45-49
50-54
55-59
60-64
Colour 5
Colour 6
Colour 5 + Colour 6
Colour 4 + Colour 5
65-69
70-74
75-79
80-84
Colour 7
Colour 8
Colour 7 + Colour 8
Colour 6+ Colour 7
85-89
90-94
95-99
100-104
Colour 9
Colour 10
110-114 Colour 11
Colour 9 + Colour 10
Colour 8 + Colour 9
115-119
120-124
125-129
130-134
Colour 12
Colour 13
Colour 12 + Colour 13
Colour 11 + Colour 12
105-109 Colour 10 + Colour 11
135-139
140-144
145-149
150-199
Colour 14
Clockwise colour scroll
Counter-clockwise colour scroll200-255
Colour 14 + White
Colour 13 + Colour 14
1 COLOUR
COLOURS 1
0
2
3
4
5
6
7
8
9
10
11
12
13
14
1 red
0 white
2 yellow
3 aquamarine blue
4
Green-yellow
green
5
light blue6
purple7
light yellow8
pink9
blue10
pale brown
light white
brown11
12
13
14 lavander

8
NAME FUNCTIONSCH VALUE
0-4
5-9
10-14
15-19
20-24
Open
Gobo 2
Gobo 4
Gobo 3
Gobo 1
25-29
30-34
35-39
40-44
Gobo 6
Gobo 8
Gobo 7
Gobo 5
45-49
50-54
55-59
60-64
Gobo 10
Gobo 12
Gobo 11
Gobo 9
65-69
70-74
75-79
80-84
Gobo 14
Gobo 16
Gobo 15
Gobo 13
85-89
90-129
130-134
135-169
Clockwise gobo scroll from fast to slow
Counter-clockwise gobo scroll from slow to fast
Stop
Gobo 17
170-174 Gobo 1 shaking from slow to fast
175-179 Gobo 2 shaking from slow to fast
180-184 Gobo 3 shaking from slow to fast
185-189 Gobo 4 shaking from slow to fast
190-194 Gobo 5 shaking from slow to fast
195-199 Gobo 6 shaking from slow to fast
200-204 Gobo 7 shaking from slow to fast
205-209 Gobo 8 shaking from slow to fast
210-214 Gobo 9 shaking from slow to fast
215-219 Gobo 10 shaking from slow to fast
4 GOBO
GOBOS
0
1
2
3
4
5
6
7
8
9
1
0
1
1
1
2
1
3
1
4
1
5
1
6
1
7

4. General Maintenance
a. Unscrew the fuse holder and remove the damaged fuse.
b. Replace with the same type fuse (F7A/250V) and screw fuse holder back in its place.
4.1 Fuse Replacement
9
EFFECT
NAME FUNCTIONSCH
5 PRISM
8 FROST
6PRISM
ROTATION
VALUE
0-127
128-255
0-127
128-191 Counter-clockwise rotation from fast to slow
Clockwise rotation from slow to fast192-255
No function
0-255 Frost 0 - 100%
9 FOCUS 0-255 Focus from far to near
Angle 0 - 400°
8-facet prism
RESET & LAMP
NAME FUNCTIONSCH
15 RESET
16 LAMP
VALUE
0-127
128-200
201-255
0 - 9
Turn lamp on （over 3 seconds）
10-100
No function
No function
No function
101-255 Turn lamp off （over 3 seconds）
Reset （over 3 seconds）
EXPAND CHANNELS
NAME FUNCTIONSCH
17 GOBO SPEED
VALUE
0-255
0 - 049
Pan Auto050-099
Gobo wheel speed from fast to slow
18 COLOR SPEED 0-255 Colour wheel speed from fast to slow
19
20 RUN MODE
FOCUS SPEED 0-255 Focus speed from fast to slow
DMX mode
100-149 Tilt Auto
150-199 Auto mode
200-255 Sound mode
4 GOBO
220-224 Gobo 11 shaking from slow to fast
225-229 Gobo 12 shaking from slow to fast
230-234 Gobo 13 shaking from slow to fast
235-239 Gobo 14 shaking from slow to fast
240-244 Gobo 15 shaking from slow to fast
245-249 Gobo 16 shaking from slow to fast
250-255 Gobo 17 shaking from slow to fast

IMPORTANT INFORMATION!
In order to optimize the recovery and recycling of the materials that old
appliances contain and reduce the impact on human health and the
environment, ensure that this product is recycled at the end of its life.
Dust build up reduces light output performance and can cause overheating. This can
lead to reduction of the light source’s life. We recommend frequent cleaning of the
fixture. When cleaning, please use a moist, lint-free cloth. Never use alcohol or
solvents.
The moving head is equipped with an Osram 230W lam. Follow the procedure below
to safely change the lamp.
4.2 Cleaning
4.3 Lamp replacement
10
Caution! Always disconnect the product from mains
power and allow it to cool down before any services.
Figure 1 Figure 2 Figure 3 Figure 4
1) Turn off the product and disconnect it from power. Wait at least 15 minutes for
lamp to cool down.
2) Use 1/4 turn screw driver to remove 2 head covers. See Figure 1.
3) Remove the fan that blows out (not the other one) by 2 screws to access the lamp.
See Figure 2-3.
4) Push the lamp reflector downward meanwhile grasp the lamp base to pull it out.
5) Remove the 2 wires connected to the lamp by the spade connectors.
6) Reverse the steps above to install the new lamp.
Warning! DO NOT touch the lamp without wearing gloves to avoid leaving grease on
the bulb or on the contacts that could reduce the lamp’s life.