Bebe Care Regency Chair & Rocker User manual

IMPORTANT:
RETAIN FOR FUTURE REFERENCE,
READ CAREFULLY
REGENCY CHAIR AND ROCKER MODEL # 094102-332

Read all instructions before assembly and use of the chair and rocker. Keep instructions
for future use.
ADULT ASSEMBLY REQUIRED:
DUE TO THE PRESENCE OF SMALL PARTS DURING ASSEMBLY, KEEP OUT OF REACH OF
CHILDREN UNTIL ASSEMBLY IS COMPLETE.
DO NOT SIT ON THE EDGE OF THE SEAT, ARMRESTS OR ON THE BACKREST AS THIS COULD
CAUSE THE CHAIR TO TIP OVER.
DO NOT USE THE CHAIR AS A STEP STOOL.
DO NOT LEAVE CHILDREN UNATTENDED ON OR BESIDETHE CHAIR.
SAFETY PRECAUTIONS
WARNING

Due to variations in the style and design of our products, the photographs and illustrations shown in this instruction
manual are generic, therefore product fabrics, colour and design may vary from images shown. CNP Brands reserves
the right to alter product specifications without notice as a result of our ongoing policy of product improvement.
Contents
Assembly contents list
Assembly / Operating instructions
How to care for your Regency Chair & Rocker
Congratulations on your purchase of the Regency Chair & Rocker.
This product has been designed and developed with safety, comfort
and functionality in mind. Please take the time to read this manual
carefully before using this product and keep it in a safe place for
future reference.
CONGRATULATIONS

ASSEMBLY CONTENTS
Check what you have received...
You have received 1 box. Please check the contents of the box against the list
below. If anything is missing, please contact Customer Service.
In Australia, contact CNP Brands on 1300 667 137, in New
Zealand contact Wainhouse Distribution on 0800 567 5000.
Supplied loose in box:
Chair
(pre-assembled) x 1
x 2
x 8
x 2
x 2
x 8
x 8
x 1
Chair leg
(front)
65mm Bolt
(for rocker)
Chair leg
(rear)
Rocker base
25mm Bolt
(for legs)
Washer
Allen key
There are no accessories recommended for us with this Bebe Care Regency Chair & Rocker.

ASSEMBLY / OPERATING INSTRUCTIONS
To assemble Chair in Rocking Mode...
Rocking mode is now ready for use.
1
2
Turn chair onto its side so the back is parallel to the
floor on a flat surface.
Line up the pre-drilled holes on the rocker feet with
the pre-drilled hole on the inside bottom base of the
chair.
As small parts are involved in assembly, children should be kept clear of the
assembly area.
Dispose of all packaging material immediately after the chair and rocker is
assembled.
Identify all parts and components.
Two people are recommended for assembly of the chair.
Spread a sheet on the floor during assembly time to protect the chair.
Place a washer over the bolt 65mm and insert the
into the hole.
Repeat for remaining hole on rocker.
Tighten bolt with supplied allen key. Be sure to no
over tighten.
Repeat with opposite side and use the remaining 2 x
65mm bolts.
1a.
1b.
a.
b.
c.
d.
e.
2a.
2b.
2c.
2d.
WARNING! DO NOT over-tighten bolts.

ASSEMBLY / OPERATING INSTRUCTIONS
To assemble in Chair Mode...
Chair mode is now ready for use.
1
2
Ensure that the legs marked with “front leg” are used
at the front side of the chair.
To determine the front and rear side, ensure that you
are looking at the chair front on.
This will ensure you have the correct front and rear
sides.
Turn the leg clockwise until it fits firmly against the
base of the chair.
Ensure that the leg sits square as per image.
Insert 2 x 25mm bolts into the pre-drilled holes as per
image.
Tighten bolt with supplied allen key.
Repeat steps 1a - 2c to assemble the 3 remaining
feet.
1a.
1b.
1c.
1d.
2a.
2b.
2c.
2d.
WARNING! DO NOT over-tighten bolts.

HOW TO CARE FOR YOUR BEBE CARE CHAIR AND ROCKER
Cleaning
Maintenance
This product has been designed and developed with safety, comfort
and functionality in mind. Please take the time to read this manual
carefully before using this product and keep it in a safe place for
future reference.
To ensure the long-lasting use of your chair and rocker, wipe down
with a damp cloth and use a mild soap solution if necessary. Do not
use abrasive cleaners.Always store product in a clean dry place.
Always check parts regularly for tightness of screws, nuts and other
fasteners – tighten or replace if required. To maintain the safety of
your chair and rocker, seek prompt repairs for bent, torn, worn or
broken parts. Use only those parts and accessories approved by
CNP Brands.
If you have any difculties in assembling the chair and rocker,please
contact our Service Department.
In Australia, contact CNP Brands on 1300 667 137, in New Zealand
contact Wainhouse Distribution on 0800 567 5000.

Distributed in Australia by CNP Brands
20 Calarco Drive,
Derrimut,VIC, 3030
Customer Service 1300 667 137
W: www.cnpbrands.com.au
E: [e-mail]
F: www.facebook.com/CNPBrands
I: @cnp_baby
Distributed in New Zealand by Wainhouse
Distribution
2-6 Argyle St, Morningside,
PO Box 41-014,
St Lukes,Auckland, New Zealand
Customer Service: 0800 567 5000
E: [e-mail]