Behringer EUROLIGHT LD6230 User manual

Version 1.1 January 2004
INSTALLATION INSTRUCTIONS
ENGLISH
EUROLIGHT
LD6230
All manuals and user guides at all-guides.com
all-guides.com

2
INSTALLATION INSTRUCTIONS EUROLIGHT LD6230
This symbol, wherever it appears, alerts you to the
presence of uninsulated dangerous voltage inside
the enclosurevoltage that may be sufficient to
constitute a risk of shock.
This symbol, wherever it appears, alerts you to
important operating and maintenance instructions
in the accompanying literature. Please read the
manual.
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: The units installation and initial operation must be
done under the supervision of a qualified
professional. To reduce the risk of electric shock,
do not remove the top cover (or the rear section .
No user serviceable parts inside; refer servicing to
qualified personnel.
WARNING: To reduce the risk of fire or electric shock, do not
expose this appliance to rain and moisture.
DETAILED SAFETY INSTRUCTIONS:
1) Read these instructi ns.
2) Keep these instructi ns.
3) Heed all warnings.
4) F ll w all instructi ns.
5) D n t use this device near water.
6) Clean nly with a dry cl th.
7) D n t bl ck any ventilati n penings. Install in
acc rdance with the manufacturers instructi ns.
8) D n t install near any heat s urces such as radiat rs,
heat registers, st ves, r ther apparatus (including
amplifiers) that pr duce heat.
9) D n t defeat the safety purp se f the p larized r
gr unding-type plug. A p larized plug has tw blades
with ne wider than the ther. A gr unding type plug
has tw blades and a third gr unding pr ng. The wide
blade r the third pr ng are pr vided f r y ur safety. If
the pr vided plug d es n t fit int y ur utlet, c nsult
an electrician f r replacement f the bs lete utlet.
10) Pr tect the p wer c rd fr m being walked n r
pinched particularly at plugs, extensi n c rds, and the
p int at which they exit the unit.
11) Only use attachments/access ries specified by the
manufacturer.
12) Use nly with the cart, stand, trip d, bracket, r table
specified by the manufacturer, r s ld with the device.
When a cart is used, use cauti n when m ving the cart/
device c mbinati n t av id injury fr m stumbling ver
it.
13) Unplug this device during lightning st rms r when
n t used f r l ng peri ds f time.
14) Refer all servicing t qualified service pers nnel.
Servicing is required when the unit has been damaged
in any way, such as p wer supply c rd r plug is
damaged, liquid has been spilled r bjects have fallen
int the device, the unit has been exp sed t rain r
m isture, d es n t perate n rmally, r has been
dr pped.
All manuals and user guides at all-guides.com

3
INSTALLATION INSTRUCTIONS EUROLIGHT LD6230
The BEHRINGER EUROLIGHT LD6230 Dimmer Pack was
developed to meet the highest demands of light engineering. Its
wide-ranging functions make it an all-purpose workhorse for
various commercial applications (TV studios, theatre or live
events .
The EUROLIGHT LD6230 has all the important features needed
to control your lighting equipment, yet its controls are clearly
arranged and simple to use. You can select between digital DMX
or analog control. You get trouble-free operation with the
extensive LEDs used for signal error detection.
IMPORTANT INFORMATION
+Installati n as well as initial perati n must be
perf rmed by qualified pers nnel. Always assure
that y ur LD6230 is c mpletely disc nnected fr m
the mains bef re rem ving the casing c ver.
+The LD6230 was designed f r ind r use nly.
+Please keep in mind that sudden temperature
changes (e.g. bringing y ur equipment fr m c lder
envir nments int warmer envir nments) may
cause c ndensati n n electr nic c mp nents,
leading t p ssible equipment damage and physical
harm t the perat r.
+Please adhere t all applicable nati nal safety
standards during installati n.
+Please read the installati n instructi ns and the
encl sed users manual in their entirety t
familiarize y urself with the LD6230 and all f its
functi ns. Please f ll w all instructi ns and st re
b th the installati n instructi ns and the manual in
a safe place f r future reference.
+Please assure that y ur EUROLIGHT is sufficiently
c led and that it is n t placed near heat s urces
that c uld cause verheating.
+If y u want t run y ur EUROLIGHT n mains v ltage
ther than fact ry-specified v ltage, c ntact the
nearest BEHRINGER service center.
+T effectively limit harm nic currents and av id
v ltage fluctuati ns that c uld affect ther electrical
appliances, c nnect this equipment t an AC utlet
that c mplies with all applicable technical standards.
In all ther cases, c ntact y ur l cal p wer supply
pr vider f r advice pri r t usage.
MAINS/ILLUMINANT CONNECTORS
To facilitate additional flexibility, your dimmer pack has a
connector terminal strip. Cable bushings for connecting to the
mains and your illuminants are located in the back. Flexibility is
further enhanced with the option to retrofit a CEE connector and
a 16-pin HARTING® connector.
Both fixed and mobile installations require compliance with IEC
61010-1:2001 (EN 6110-1:2001 . In particular, a 3-phase
separator (pursuant IEC60947-1 and IEC60947-3 needs to be
included in the installation. This separator needs to be labeled
according to IEC 60417-50008 and IEC 0417-5007.
To assure compliance with Directive 89/336/EEC, only use
specified upstream line filters with your EUROLIGHT. Using it
without line filters specified by BEHRINGER may lead to
electromagnetic interference. More detailed information on this
subject can be found at www.behringer.com.
SAFETY AND INITIAL OPERATION
As soon as you connect your LD6230 to the mains, internal
controls are activated. The six automated fuses (circuit breakers
can all handle 10 A and serve as overload protection for the
connected equipment.
+Please keep in mind that activating circuit breakers
1, 2, 3, 4, 5 r 6 als means that the respective
channels can c nduct v ltage.
Electronic controls are additionally protected with triple high-
sensitivity fuses located on the main board.
+Defective fuses must be replaced with fuses with
identical rating!
The LD6230 is a Class I device in which a low-Ohm protective
ground wire is an integral part of its safety design.
During the installation, make sure that a low-Ohm protective
conductor (< 0,1 Ohm exists between all bare metal parts and
the grounding on the main connector.
3KDVH &+ CH 2 &+ CH 4 &+ CH 6
L1 X X
L2 X X
L3 X X
2XWSXWFKDQQHOV
* Activation of control electronics and respective output channel
CONNECTOR TERMINAL STRIP
The connector terminal strip of your LD6230 is laid out for
cables with diameters between 0.326 mm2 (AWG 22 and
4 mm2 (AWG 12 . When using flexible access lines, cable end
contacts corresponding to manufacturer specifications have
to be used. To assure good contact, skin the cable endings
between 9 - 13 mm.
During the installation, all applicable national standards need
to be adhered to.
Illustration: LD6230 connector terminal strip
When your LD6230 leaves the assembly plant, all incoming
and outgoing neutral conductor connectors are bridged.
The incoming phases L1/L1, L2/L2 and L3/L3 are always
connected to one another in pairs and switched to the overload
protection of the channels 1 to 6. They protect output connectors
E1 to E6 . Each of the channels can handle currents of
maximum 10 Amperes. The green-yellow conductors (PE
may only be used as protective conductors.
All manuals and user guides at all-guides.com

4
INSTALLATION INSTRUCTIONS EUROLIGHT LD6230
The lowest cable gauge between L1 and L3, incoming neutral
conductor (N and protective earth (PE is 4 mm2
(AWG 12 . For outgoing channels E1 to E6, use cables with
gauges corresponding to the loads used (2.5 mm2 (AWG 14 or
1.5 mm2 (AWG 16 .
2XWSXWDVVHVVPHQW>$@ 1RPLQDOFURVV
VHFWLRQ>PP

@(8
$:*
86$
6 - 10 1.5 16
13 - 16 2.5 14
18 - 25 4 12
+During the installati n, please adhere t all
manufacturer instructi ns. Regardless from mains
supply voltage, the maximum utput current f the
EUROLIGHT LD6230 is 10 A per dimmer circle.
+Please make sure that each dimmer l ad is
c nnected t a separate channel. Never c nnect
m re than ne utput t just ne c mm n neutral
c nduct r.
+ATTENTION: Due t electr cuti n danger, d n t use
y ur dimmer pack if there are bare cables visible.
CONNECTION OPTIONS FOR
FLEXIBLE USAGE
OUTPUT CONNECTOR (HARTING®)
In the back of your LD6230 there is a cable bushing for
connecting your illuminants. Open the flap on the top of the
LD6230 to get to the terminal clamps used for this purpose. Here
you have the option to retrofit a 16-pin HARTING® connector. To
do that, you first have to remove the back-bearing cover sheet
and connect the HARTING® connector to the terminal clamps.
PIN 1 Phase channel 1 E1 PIN 9 Neutral channel 1 N
PIN 2 Phase channel 2 E2 PIN 10 Neutral channel 2 N
PIN 3 Phase channel 3 E3 PIN 11 Neutral channel 3 N
PIN 4 Phase channel 4 E4 PIN 12 Neutral channel 4 N
PIN 5 Phase channel 5 E5 PIN 13 Neutral channel 5 N
PIN 6 Phase channel 6 E6 PIN 14 Neutral channel 6 N
PIN 7 free - PIN 15 free -
PIN 8 free - PIN 16 free -
3,1DVVLJQPHQW+$57,1*

FRQQHFWRU
Ground wires need to be fastened
to their respective PE connectors
CEE POWER SUPPLY CONNECTOR
Also located in the back is a cable bushing for the mains
supply. Here, you can retrofit a 5-pin CEE 32 A mains connector
by removing the back-bearing cover sheet and connect the CEE
high-voltage connector to the connecting terminal. The following
illustration shows how the connections are allocated:
CEE connector pin allocation
+Rem vable mains c nnect r cables with mains
interc nnecti ns (pursuant IEC60320) must match
the minimal l ad-carrying capacity f the c nnect r
r must c mply with the IEC60799 standard. The
interc nnecti n and the cable must c mply with
prevalent n minal values (maximal v ltage and
current).
+During the installati n, please adhere t the
instructi ns pr vided by the c nnect r
manufacturer.
SPECIFICATIONS
Channels
Number 6
Load per channel 0.2 A min./10 A max.
Maximal load per channel 10 A using a 3-phase connector
Frequency 50/60 Hz
Inputs
Power supply 3-phase connector, internal
terminal block/PG cable screw
joint, CEE connector (optional
installation by qualified
personnel
Analog 0 to +10 V via 8 pin DIN
Digital DMX512 via XLR 5 pin
Outputs
Digital DMX512 via XLR 5 pin
Load Internal terminal block/PG cable
screw joint, HARTING® (optional
installation by qualified
personnel
System fuses
Load securing per channel 10 A cable protection switch
(type C
Control section fuse 2 x T 100 mA H/250 V
1 x T 160 mA H/250 V
for voltage range 220 - 230 V (EU
2 x T 160 mA H/250 V
1 x T 315 mA H/250 V
for voltage range 120 V (UL
P wer supply
Voltage USA/Canada
120 V~, 60 Hz
Europe/U.K./Australia
240 V~, 50 Hz
Maximum power consumption 3 x 20 A
Dimensi ns/Weight
Dimensions (H x W x D approx. 3 1/3" (84.3 mm
x 19" (482.6 mm
x 15 9/10" (403.8 mm
Weight approx. 20.3 lbs. (9.2 kg
BEHRINGER continuously strives to assure the highest quality
standards possible. Required modifications may be implemented without
prior notice. echnical data and the appearance of the unit may deviate
from the above values and/or illustrations.
All manuals and user guides at all-guides.com

5
INSTALLATION INSTRUCTIONS EUROLIGHT LD6230
Technical specifications and appearance subject to change without notice. The information contained herein is correct at the time of
printing. The names of companies, institutions or publications pictured or mentioned and their respective logos are registered
trademarks of their respective owners. Their use neither constitutes a claim of the trademarks by BEHRINGER® nor affiliation of the
trademark owners with BEHRINGER®. BEHRINGER® accepts no liability for any loss which may be suffered by any person who relies
either wholly or in part upon any description, photograph or statement contained herein. Colours and specification may vary slightly
from product. Products are sold through our authorised dealers only. Distributors and dealers are not agents of BEHRINGER® and
have absolutely no authority to bind BEHRINGER® by any express or implied undertaking or representation. No part of this manual may
be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording of any
kind, for any purpose, without the express written permission of BEHRINGER Spezielle Studiotechnik GmbH. BEHRINGER® is a
registered trademark.
ALL RIGHTS RESERVED. © 2004 BEHRINGER Spezielle Studiotechnik GmbH,
Hanns-Martin-Schleyer-Str. 36-38, 47877 Willich-Münchheide II, Germany.
Tel. [phone], Fax [phone]
All manuals and user guides at all-guides.com