Behringer 2500 Series User manual

Quick Start Guide
DUAL ENVELOPE
GENERATOR MODULE 1003
Legendary 2500 Series Dual Envelope
Generator Module for Eurorack
Controls
(1) (2)
(3)
(4)
(5)
(6)
(7)
(8) (9) (10) (11)
(1) ATTACK TIME – Adjusts the rate at which the envelope
reaches its peak voltage.
(2) SIGNAL LED – Indicates when a gate signal is present.
(3) INITIAL DECAY TIME – Adjusts the rate at which the
envelope decays from its peak to its designated
sustain level.
(4) SUSTAIN LEVEL – Controls the level at which the
envelope remains after its peak but before release,
sustaining as long as the input signal is present or the
manual gate button is held down.
(5) FINAL DECAY TIME – Controls how quickly the envelope
falls after the input signal stops or the manual gate button
is released.
(6) TRIGGER MODE – Selects between single mode,
where only the gate signal controls the envelope,
or multiple mode, which uses a positive trigger pulse to
re-trigger the envelope while a gate signal is present.
(7) MANUAL GATE – Press and hold to start the
envelope cycle.
(8) GATE– Connect a gate signal to control the envelope cycle.
(9) TRIG – Triggers a new attack of the envelope if a gate
signal is also present.
(10) OUT L – Send the left envelope positive and negative
control voltage to other modules via 3.5 mm TS cable.
(11) OUT R – Send the right envelope positive and negative
control voltages to other modules via 3.5 mm TS cable.
Power Connection
The unit comes with the required power cable for connecting
to a standard Eurorack power supply system. Follow these
steps to connect power to the module. It is easier to make these
connections before the module has been mounted into a
rack case.
1. Turn the power supply or rack case power o and
disconnect the power cable.
2. Insert the 16-pin connector on the power cable into the
socket on the power supply or rack case. The connector has
a tab that will align with the gap in the socket, so it cannot
be inserted incorrectly. If the power supply does not have
a keyed socket, be sure to orient pin 1 (-12 V) with the red
stripe on the cable.
3. Insert the 10-pin connector into the socket on the back of
the module. The connector has a tab that will align with the
socket for correct orientation.
4. After both ends of the power cable have been securely
attached, you may mount the module in a case and turn on
the power supply.
V 1.0

Installation
The necessary screws are included with the module for mounting
in a Eurorack case. Connect the power cable before mounting.
Depending on the rack case, there may be a series of xed holes
spaced 2 HP apart along the length of the case, or a track that
allows individual threaded plates to slide along the length
of the case. The free-moving threaded plates allow precise
positioning of the module, but each plate should be positioned in
the approximate relation to the mounting holes in your module
before attaching the screws.
Hold the module against the Eurorack rails so that each of the
mounting holes are aligned with a threaded rail or threaded
plate. Attach the screws part way to start, which will allow
small adjustments to the positioning while you get them all
aligned. After the nal position has been established, tighten the
screws down.
Specications
Inputs
Gate
Type 3.5 mm TS jack, DC coupled
Impedance >35 kΩ
Gate threshold +4 V
Max input level +12 V
Trig
Type 3.5 mm TS jack, DC coupled
Impedance >20 kΩ
Trigger threshold +4 V
Max input level +12 V
Outputs
Out A
Type 2 x 3.5 mm TS jacks, DC coupled
Impedance 1 kΩ
Max output level -10 V or +10 V
Out B
Type 2 x 3.5 mm TS jacks, DC coupled
Impedance 1 kΩ
Max output level -10 V or +10 V
Controls
Attack 1 ms to 2 s
Initial decay 5 ms to 7 s
Sustain 0 to 10 V
Final decay 6 ms to 8 s
Trigger modes Single - gate controls envelope
Multiple - trigger pulse +
gate controls envelope
Manual gate Envelope cycle start
Power
Power supply Eurorack
Current draw 40 mA (+12 V), 20 mA (-12 V)
Physical
Dimensions 42 x 81 x 129 mm
(1.7 x 3.2 x 5.1")
Rack units 16 HP
Weight 0.16 kg (0.35 lbs)
LEGAL DISCLAIMER
Music Tribe accepts no liability for any loss which may be suered by any
person who relies either wholly or in part upon any description, photograph,
or statement contained herein. Technical specications, appearances and
other information are subject to change without notice. All trademarks are the
property of their respective owners. Midas, KlarkTeknik, Lab Gruppen, Lake,
Tannoy,Turbosound,TC Electronic, TC Helicon, Behringer, Bugera, Auratone
and Coolaudio are trademarks or registered trademarks of MusicTribe
Global Brands Ltd. © Music Tribe Global Brands Ltd. 2020 All rights reserved.
LIMITED WARRANTY
For the applicable warranty terms and conditions and additional information
regarding MusicTribe’s Limited Warranty, please see complete details online
at musictribe.com/warranty.