Behringer ULTRAPATCH PX1000 User manual

Version 1.1 March 2003
Users Manual
ENGLISH
ULTRAPATCH PX1000
All manuals and user guides at all-guides.com
all-guides.com

2
ULTRAPATCH PX1000
3. CAUTIONS
Welcome to the BEHRINGER family!
Thank you very much for expressing your confidence in
BEHRINGER products by purchasing the U TRAPATCH PX1000.
The PX1000 is a multi-functional balanced 48-point patchbay for
studio and stage applications.
A patchbay allows you to patch the audio signals of most
components in your studio from a central point and send them to
other units, making your entire cabling better structured and
optimally suited for professional work. If you want to use your
studio as effectively as possible, it is preferable to use a complete
patchbay wiring scheme, but even smaller studio configurations
will benefit from less complex patchbay configurations.
1. PATCHBAY CONFIGURATION
The majority of commercially available patchbays include two
rows of 24 phone jacks in a single 19" rack panel. On the rear,
either a corresponding number of phone jacks or contacts for
soldering signal leads can be found. Each group of four phone
jacks forms one module. The configuration of some patchbays
can be changed by inserting jumpers or turning individual modules.
With the BEHRINGER U TRAPATCH PX1000 you own an
easy-to-use 48-point patchbay offering 1/4" TRS connectors, that
can be operated in five different modes simply by aligning the
modules manually. For this purpose, simply loosen the two lower
front screws to remove the front panel.
1.1 Mode 1
)5217 5($5
$$
%%
In this mode, when all jacks of the module are inserted, the
audio signals A and B will go separately from front to rear. For
example, you may use this mode to connect mixer outputs to
compressor inputs or compressor outputs to tape inputs.
1.2 Mode 2
)5217 5($5
$$
%%
In this mode, the contacts of jacks A & B on the front are
interconnected. When you insert a plug into the upper rear jack
(A), the signal routed through the front path is not interrupted.
Only when the lower rear jack (B) is used will the front panel
route be split, so that the two upper and the two lower jacks are
connected to one another. This configuration is called input
break and is used mainly for insert applications.
1.3 Mode 3
)5217 5($5

$$
%%
Here, the contacts of jacks A & B on the rear are inter-
connected. When you insert a plug into the upper front jack (A),
the signal routed through the rear path is not interrupted and the
audio source of front A is parallel to the rear jacks (A & B).
Thus, two power amplifiers may, for example, share one audio
source.
1.4 Mode 4
)5217 5($5
$$
%%
In this configuration, the contacts of jacks A & B on the front
are interconnected. Thus, the upper front jack (A) receives an
incoming signal and the lower front jack (B) sends the outgoing
signal. With this mode, you can take the signal from lower front
jack (B) for recording purposes or the connection to additional
equipment.
1.5 Mode 5
)5217 5($5

$$
%%
Here, the contacts of jacks A & B on the rear are inter-
connected. The configuration is the same as in mode 4. However,
in contrast to mode 4, this mode is usually deployed for equipment
in a fixed installation. For example, most recording studios have
the mixers outputs connected to the recorders inputs most of
the time. It is very convenient to have the signal path through the
patchbay in this manner, with the permanent connections made
at the rear. This also allows you to intercept, divert or replace
the signal easily at the front of the patchbay in a number of ways
by inserting a plug into one of the front jacks (A or B).
2. LOOMING PROBLEMS
oom wiring is an art in itself, and it is worth the time to get it
right. First, it is important to avoid ground loops (a looped wire
acts like an antenna, picking up hum and electromagnetic
radiation). Think of a tree. Every part of that tree is connected
to every other part, but only by one route. Thats how the total
grounding picture for your entire studio should look. Dont remove
the ground connection of your mains cable plug to reduce audible
50/60 Hz mains hum. Instead, you should disconnect the signal
shield somewhere (one or several audio cables) in the signal
chain.
It is good practice to ensure that all screens are commoned at
the patchbay, in which case all equipment would be grounded
from this point via a single screen (more than one route = an
earth loop), while mains-earthed equipment would have all
screens cut at the equipment end.
Some equipment has an independent signal and mains
grounding. In this case, at least one screen should ground the
equipment. Sometimes, the only way to find out is suck and
see.
Please assure that using the patchbay does not disturb the
studios grounding architecture. Always use patch leads that
are as short as possible with the screen connected at both
ends.
After removing the mains hum from the system, make up your
cable looms from the patchbays outwards, and use cable ties,
flexible sheaths, multicores, etc. to keep the back of your racks
orderly.
3. CAUTIONS
Avoid routing digital signals near a patchbay because the pulse
signal used for the transmission of such signals causes heavy
interference in analog signals. Additionally, normal patchbays
change the impedance of the digital cable route, which
causes interference in the digital path. Use the BEHRINGER
U TRAMATCH PRO SRC2496 specifically designed for this and
other digital signal-related functions.
All manuals and user guides at all-guides.com

3
ULTRAPATCH PX1000
6. SPECIFICATIONS
Microphone inputs operate at a level several orders of magnitude
lower than line levels (+4 dBu or -10 dBV). Therefore, they
should never be routed via a patchbay. In any case, patching in
a field with +48 V DC (phantom power) is to be avoided at all
costs. It is best to plug mics directly into the mixing console or via
special X R type wall boxes connected to the mic inputs of the
console using good quality balanced multicore cables.
4. LABELLING
With so many patch points in use at any one time, you will
probably never be able to keep track of them without labelling.
Your BEHRINGER U TRAPATCH PX1000 features white labels
above the upper jacks and white labels below the lower jacks
for the purpose of labelling. When labelling, it is advisable not to
use permanent markers as you may want to re-label, if you
decide to re-configure your patchbay signal routing again.
5. PATCHBAY ORGANIZATION
Attached is an example configuration that shows how you
can use your patchbay. This is only an example to illustrate the
use of your PX1000. Depending on your application, you may
need several PX1000s. It should be noted that patchbays should
be placed one below the other in such a way that the patch
cords dont hang carelessly over the patchbays.
6. SPECIFICATIONS
Height 1 3/4" (44.5 mm)
Width 19" (482.6 mm)
Depth 2 3/4" (69.3 mm)
Weight approx. 1.3 kg (2 7/8 lbs)
Connectors 1/4" TRS balanced
BEHRINGER is constantly striving to maintain the highest professional standards. As a
result of these efforts, modifications may be made from time to time to e isting products without
prior notice. Specifications and appearance may differ from those listed or shown.
All manuals and user guides at all-guides.com

4
ULTRAPATCH PX1000
7. WARRANTY
§ 1 WARRANTY CARD/ONLINE REGISTRATION
To be protected by the extended warranty, the buyer must
complete and return the enclosed warranty card within 14 days
of the date of purchase to BEHRINGER Spezielle Studiotechnik
GmbH, in accordance with the conditions stipulated in § 3. Failure
to return the card in due time (date as per postmark) will void any
extended warranty claims. Based on the conditions herein, the
buyer may also choose to use the online registration option via
the Internet (www.behringer.com or www.behringer.de).
§ 2 WARRANTY
1. BEHRINGER (BEHRINGER Spezielle Studiotechnik GmbH
including all BEHRINGER subsidiaries listed on the enclosed page,
except BEHRINGER Japan) warrants the mechanical and
electronic components of this product to be free of defects in
material and workmanship for a period of one (1) year* from the
original date of purchase, in accordance with the warranty
regulations described below. If the product shows any defects
within the specified warranty period that are not excluded from
this warranty as described under § 3 and 4, BEHRINGER shall, at
its discretion, either replace or repair the product using suitable
new or reconditioned parts. In the case that other parts are used
which constitute an improvement, BEHRINGER may, at its
discretion, charge the customer for the additional cost of these
parts.
2. If the warranty claim proves to be justified, the product will
be returned to the user freight prepaid.
3. Warranty claims other than those indicated above are
expressly excluded.
§ 3 RETURN AUTHORIZATION NUMBER
1. To obtain warranty service, the buyer (or his authorized
dealer) must call BEHRINGER (see enclosed list) during normal
business hours BEFORE returning the product. All inquiries must
be accompanied by a description of the problem. BEHRINGER
will then issue a return authorization number.
2. Subsequently, the product must be returned in its original
shipping carton, together with the return authorization number to
the address indicated by BEHRINGER.
3. Shipments without freight prepaid will not be accepted.
§ 4 WARRANTY REGULATIONS
1. Warranty services will be furnished only if the product is
accompanied by a copy of the original retail dealers invoice.
Any product deemed eligible for repair or replacement by
BEHRINGER under the terms of this warranty will be repaired or
replaced within 30 days of receipt of the product at BEHRINGER.
2. If the product needs to be modified or adapted in order to
comply with applicable technical or safety standards on a national
or local level, in any country which is not the country for which
the product was originally developed and manufactured, this
modification/adaptation shall not be considered a defect in
materials or workmanship. The warranty does not cover any
such modification/adaptation, irrespective of whether it was
carried out properly or not. Under the terms of this warranty,
BEHRINGER shall not be held responsible for any cost resulting
from such a modification/adaptation.
3. Free inspections and maintenance/repair work are expressly
excluded from this warranty, in particular, if caused by improper
handling of the product by the user. This also applies to defects
caused by normal wear and tear, in particular, of faders,
potentiometers, keys/buttons and similar parts.
4. Damages/defects caused by the following conditions are
not covered by this warranty:
simproper handling, neglect or failure to operate the unit in
compliance with the instructions given in BEHRINGER user
or service manuals.
sconnection or operation of the unit in any way that does not
comply with the technical or safety regulations applicable in
the country where the product is used.
sdamages/defects caused by force majeure or any other
condition that is beyond the control of BEHRINGER.
5. Any repair or opening of the unit carried out by unauthorized
personnel (user included) will void the warranty.
6. If an inspection of the product by BEHRINGER shows that
the defect in question is not covered by the warranty, the
inspection costs are payable by the customer.
7. Products which do not meet the terms of this warranty will
be repaired exclusively at the buyers expense. BEHRINGER will
inform the buyer of any such circumstance. If the buyer fails to
submit a written repair order within 6 weeks after notification,
BEHRINGER will return the unit C.O.D. with a separate invoice
for freight and packing. Such costs will also be invoiced
separately when the buyer has sent in a written repair order.
§ 5 WARRANTY TRANSFERABILITY
This warranty is extended exclusively to the original buyer
(customer of retail dealer) and is not transferable to anyone
who may subsequently purchase this product. No other person
(retail dealer, etc.) shall be entitled to give any warranty promise
on behalf of BEHRINGER.
§ 6 CLAIM FOR DAMAGES
Failure of BEHRINGER to provide proper warranty service shall
not entitle the buyer to claim (consequential) damages. In no
event shall the liability of BEHRINGER exceed the invoiced value
of the product.
§ 7 OTHER WARRANTY RIGHTS AND NATIONAL LAW
1. This warranty does not exclude or limit the buyers statutory
rights provided by national law, in particular, any such rights
against the seller that arise from a legally effective purchase
contract.
2. The warranty regulations mentioned herein are applicable
unless they constitute an infringement of national warranty law.
* Customers in the European Union please contact BEHRINGER
Germany Support for further details.
The information contained in this manual is subject to change without notice. No part of this manual may be reproduced or
transmitted in any form or by any means, electronic or mechanical, including photocopying and recording of any kind, for any
purpose, without the express written permission of BEHRINGER Spezielle Studiotechnik GmbH.
BEHRINGER, U TRAPATCH and U TRAMATCH are registered trademarks.
A RIGHTS RESERVED.
© 2003 BEHRINGER Spezielle Studiotechnik GmbH.
BEHRINGER Spezielle Studiotechnik GmbH, Hanns-Martin-Schleyer-Str. 36-38, 47877 Willich-Münchheide II, Germany
Tel. [phone] / 92 06-0, Fax [phone] / 92 06-30
7. ARRANTY
All manuals and user guides at all-guides.com