Belkin OmniView F1DD102U User manual

User Manual
SOHO Series
F1DD102U
F1DD104U
OmniView
Control multiple DVI/USB computers with
one USB keyboard and mouse, and DVI monitor
KVM Switch with Audio
™

TABLE OF CONTENTS
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Overview
Feature Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Equipment Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
Operating Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Unit Display Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Pre-Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Step-by-Step Installation Guide
Installing the Switch Base . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Installing the HID USB Driver . . . . . . . . . . . . . . . . . . . . . . . . .10
Connecting the Console . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Connecting the PCs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Powering Up the Systems . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Using Your KVM Switch
Selecting a Computer Using Direct-Access Port Selectors . . . . . . . .15
Selecting a Computer Using Keyboard Hot Key Commands . . . . . . .15
AutoScan Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Connecting USB Devices to the Built-In 2-Port Hub . . . . . . . . . . .16
Belkin KVM Switches and Accessories
OmniView KVM Switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
OmniView KVM Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
OmniView KVM Accessories and Adapters . . . . . . . . . . . . . . . . . .22
FAQs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
Warranty, FCC, ICES, and CE Statements . . . . . . . . . . . . . . . . . . . . .28

INTRODUCTION
1
Congratulations on your purchase of the Belkin OmniView SOHO Series KVM
Switch with Audio (the KVM Switch). Our diverse line of quality KVM
solutions exemplifies the Belkin commitment to delivering high-quality,
durable products at a competitive price. Engineered to give you control over
multiple computers/servers from one console, Belkin KVM Switches come in
a variety of capacities suitable for all configurations, large or small. This
compact, affordable Belkin OmniView KVM Switch is backed by a Belkin
Five-Year Warranty and free technical support.
This manual will provide details about your new KVM Switch, from
installation and operation, to troubleshooting—in the unlikely event of
a problem.
For easy installation, please refer to the Quick Installation Guide included
with your KVM Switch.
Thank you for purchasing the Belkin OmniView SOHO Series KVM Switch with
Audio. We appreciate your business and have confidence that you will soon
see for yourself why over 1 million Belkin OmniView KVM Switches are being
used worldwide.
Contents of Package:
•OmniView SOHO Series KVM Switch with Audio
•Attachable Base
•DB25 to RJ45 Flash Cable
•User Manual
•Quick Installation Guide
•Registration Card
•9V DC, 1A Power Supply

Feature Overview
The OmniView SOHO Series KVM Switch with Audio (the KVM Switch)
allows you to control up to four computers, with one USB keyboard and
USB mouse and a DVI-D video monitor.
USB Hot Keys
Hot keys allow you to select ports using designated key commands from
your USB keyboard. Control up to two (for the 2-port unit) or four
(for the 4-port unit) computers, using a simple hot key sequence on
your keyboard.
AutoScan
The AutoScan feature allows you to automatically scan and monitor the
activities of all operating computers connected to your KVM Switch, one
by one.
Video Resolution
The KVM Switch supports video resolutions of up to 1600x1200@60Hz. To
preserve signal integrity at high resolutions, Belkin KVM Cables for SOHO
Series with Audio (Belkin part number F1D9201-XX) are recommended.
Flash Upgrade
Flash upgradeability allows you to obtain the latest firmware upgrades for
your KVM Switch. These upgrades will let your KVM Switch continue to be
compatible with the latest devices and computers. Firmware upgrades are
free for the lifetime of the product. Visit belkin.com for upgrade
information and support, or see the enclosed instruction document.
Microphone/Audio Support
The KVM Switch supports USB-type speakers and microphones and has
built-in microphone and speaker jacks to support the growth of
multimedia use in small-office and home-office environments. This feature
eliminates the need to disconnect and reconnect these devices when
switching between computers, and reduces the clutter on your desktop
with fewer speakers.
OVERVIEW
2

3
OVERVIEW
Direct-Access Port Selectors
Direct-access port selectors, conveniently located on the front face of the
KVM Switch, allow for simple, manual port selection.
Cable Management
The designed enclosure offers built-in cable management to contain
connected cables. Once the cables have been connected and the shroud
slid into place, the cables are conveniently maintained through the
back opening.
LED Display
An LED display is added to the face of the KVM Switch for easy status
monitoring. A lit LED indicates which computer the console has control
of. The corresponding direct-access port selector is located next to the
LED. When pushed, the LED should light next to the port selector.
USB Device Ports
Two USB device ports allow you to add shared peripherals. This reduces
cable clutter and eliminates the need to disconnect and reconnect
devices when switching between computers.

OVERVIEW
4
Equipment Requirements
Cables
For each USB computer to be connected to the KVM Switch, one DVI
cable and one USB cable is necessary.
To support resolutions of up to 1600x1200@60Hz, use Belkin KVM Cables
for SOHO Series with Audio (Belkin part number F1D9201-XX) to preserve
signal integrity. Cables must have DVI male to DVI male connectors.
Belkin OmniView KVM Cables for SOHO Series with Audio offer the highest
quality possible to ensure that your data is optimally transmitted and
include PC99 color-coded connectors for easier identification and
connection. The following cables are recommended for your KVM Switch:
F1D9201-XX (USB Style)
-XX denotes the length in feet.
Available in 6- and 10-foot lengths.

OVERVIEW
5
Operating Systems
Your KVM Switch is for use on CPUs using:
Platforms
•Windows®98/2000/Me/XP, Mac®OS*, Linux®*
*with USB support
Keyboards
•Supports 101-/102-/104-/107-key USB keyboards
Mice
•USB-compatible USB mice with 2, 3, 4, or 5 buttons
Monitors
•DVI-D
•VGA (with DVI to DB15 adapter)
•SVGA (with DVI to DB15 adapter)
•MultiSync® (with DVI to DB15 adapter)
Microphone
•Multimedia microphone with 3.5mm connectors
Audio
•Multimedia speaker/stereo with 3.5mm connectors
Power Supply
•9V 1A power supply required (center pin positive)
Unit Display Diagrams
The front of the KVM Switch
•Direct-access port selector
•LED for identification of selected port
•Removable shroud

OVERVIEW
6
Console USB keyboard
RJ45 flash port
Console USB mouse
1st computer
USB port—USB 1
2nd computer
USB port—USB 2
2nd computer
DVI port—DVI 2 2nd computer
audio/microphone jacks
1st computer
audio/microphone jacks
Console
audio/microphone
jacks
1st computer
DVI port–DVI 1
Console DVI port
USB device ports
9V 1A power jack
The back of the KVM Switch:

OVERVIEW
7
Where to Place the KVM Switch
The compact size of the KVM Switch makes it perfect for desktop
placement. Consider the following when deciding where to place the KVM
Switch: whether or not you intend to use the direct-access port selectors;
the length of the cables attached to your keyboard, mouse, and monitor;
the location of your CPUs from your Console; and the length of the cables
you will use to connect your computers to the KVM Switch.
Cable Distance Requirements
USB signals are the strongest when transmitted up to 15 feet between
the KVM Switch and the CPU. Beyond 15 feet, probability of signal
degradation increases, which can cause the device to fail.
Cautions and Warnings
Avoid having cables near fluorescent lights, air conditioning equipment, or
machines that create electrical noise (e.g., vacuum cleaners).

OVERVIEW
8
Specifications
Part No.: F1DD102U, F1DD104U
Power: 9V DC, 1A power adapter (required)
PCs Supported: 2 (F1DD102U), 4 (F1DD104U)
Monitor Supported: VGA and SVGA MultiSync, LCD (with DVI to VGA
Adapter), DVI-D monitors
Max Resolution: 1600x1200@60Hz
Keyboard Input: USB
Mouse Input: USB
USB Device Ports: 2
Audio Input/Output: 3.5mm jack (stereo)
Microphone Input/Output: 3.5mm jack
Video Port: 24-pin DVI type
CPU Connectors: DVI-I and USB “B” type
LED Indicators: 2 (F1DD102U), 4 (F1DD104U)
Enclosure: High-impact plastic
Dimensions:
F1DD102U
6.75 (h) x 4.25 (w) x 7.75 (d) inches
F1DD104U
7.75 (h) x 4.75 (w) x 9.5 (d) inches
Weight:
F1DD102U 1.5 lbs.
F1DD104U 2.0 lbs.
Operating Temp: 32° to 104° F
Storage Temp: -4° to 140° F
Humidity: 0-80% RH, non-condensing
Warranty: 5 years
Note: Specifications are subject to change without notice.

STEP-BY-STEP INSTALLATION GUIDE
9
This section provides complete instructions for the hardware setup of a
single KVM Switch. (F1DD102U, F1DD104U)
Installing the KVM Switch Base
Hold the main housing with one hand and the base with the other.
With the narrow part of the base facing toward the rear of the housing,
align the hooks of the base to the base holes located underneath the
housing. Put the hooks through the holes and push the base toward the
front of the housing to lock the base into place. Please refer to diagram
for assistance.

10
STEP-BY-STEP INSTALLATION GUIDE
Installing the HID USB Driver
Note: On some computers, you must enable USB support on your system
BIOS. Please reference your computer manufacturer’s manual or
motherboard manual to verify that USB support is enabled.
1. Connect the 9V, 1A power adapter to the KVM Switch.
2. Boot up the computer you wish to connect via USB as you would
normally with the USB keyboard, monitor, and USB mouse connected
directly to the computer.
3. After the operating system finishes loading, using a standard
USB A-to-B cable, insert the end with the B-type connector to any
KVM Switch CPU port. Insert the other end of the cable with the A-
type connector to an available port on your USB computer. Your
computer should recognize your KVM Switch and automatically install
the HID USB driver. Once the driver is installed, you can power down
your computer.
4. Repeat steps 1 through 3 for each additional USB computer you wish
to connect to the KVM Switch.

11
STEP-BY-STEP INSTALLATION GUIDE
Connecting the Console
1. Power down your computers.
2. Remove the rear panel of the KVM Switch to expose the ports.
3. Connect the USB keyboard to the
designated USB port with the keyboard symbol
on the KVM Switch.
Note: You must connect the USB keyboard
to the designated USB connector to
have keyboard hot key
switching functions. For more
information on keyboard hot
keys, see page 14.
4. Connect the USB mouse to
the designated USB port
with the mouse symbol
on the KVM Switch.
5. Connect any USB devices
you wish to share to the USB hub labeled “Device 1, Device 2” on the
KVM Switch.
Note: When sharing USB storage devices, CD-RWs, or
hard drives, do not switch while operating.
6. Connect the monitor cable to the
designated “Console DVI”
port on the KVM Switch.

STEP-BY-STEP INSTALLATION GUIDE
12
7. Using the audio cable attached to your speakers, connect the male
3.5mm plug to “audio” on the Console of your KVM Switch. (This step
is not required to use the KVM Switch.)
8. Using the mic cable attached to your microphone, connect the male
3.5mm plug to “mic” on the Console of your KVM Switch. (This step is
not required to use the KVM Switch.)

STEP-BY-STEP INSTALLATION GUIDE
13
Connecting the PCs
1. Using your Belkin KVM Cables for SOHO Series with Audio (Belkin part
number F1D9201-XX), connect the USB cable from your computer’s
USB port to the USB port on the KVM Switch.
2. Take the DVI cable and connect the male end of the cable to the DVI
port on the back of the computer. Connect the other male end of the
DVI cable to the back of the KVM Switch for CPU1.
Repeat Steps 1 and 2 for all computers.

STEP-BY-STEP INSTALLATION GUIDE
14
3. Using the audio cable, connect one end of the male 3.5mm plug to
the “Speaker Out” jack of your sound card or computer, and connect
the other end of the “audio” jack to your KVM Switch.
4. Using a second audio cable, connect one end of the male 3.5mm plug
to the “Mic Out” jack of your sound card or computer, and connect the
other end of the “mic” jack to your KVM Switch.
Powering Up the Systems
Once all cables have been connected, turn on all CPUs that are attached
to the KVM Switch. All computers can be powered on simultaneously. Your
KVM Switch should be ready for use.

USING YOUR KVM SWITCH
15
You can select which computer to operate by either the direct-access port
selector located on the front panel of the KVM Switch or through
keyboard hot key commands. Note that it will take 1–2 seconds for the
video to display after switching. This is due to the refresh rate of the
video signal. There is also re-synchronization of the mouse and keyboard
signal that takes place. This is normal operation and ensures that proper
synchronization is established.
Selecting a Computer Using Direct-Access Port Selectors
You can directly select which computer you wish to control by pressing
the corresponding direct-access port selector next to the appropriate
port. The LED will be lit to indicate that the port is currently selected.
Selecting a Computer Using Keyboard Hot Key Commands
Note: You must connect the USB keyboard to the designated USB
connector to have keyboard hot key switching function on
the keyboard.
You can command the KVM Switch to switch ports with a simple keyboard
command sequence by using the [SCROLL LOCK] key and [UP], [DOWN]
arrow keys. To send commands to the KVM Switch, the [SCROLL LOCK] key
must be pressed twice within two seconds. You will hear a beep for
confirmation. Then you can press the [UP], [DOWN] arrow keys to switch
between ports.
You can switch directly to any port by entering the port number of the port
you wish to use. For example, if you press [SCROLL LOCK], [SCROLL LOCK],
[2], the computer on port 2 will be selected.
Switch to port 2—#2 key Switch to port 4—#4 key
Switch to next active port,
[UP] arrow Switch to previous active port,
[DOWN] arrow

USING YOUR KVM SWITCH
16
AutoScan Mode
In AutoScan mode the KVM Switch remains on one port for 10 seconds
before switching to the next. This time interval cannot be changed.
To enable AutoScan mode press [SCROLL LOCK], [SCROLL LOCK],
[0], [0]
Note: There is no mouse or keyboard control in this mode. This is necessary
to prevent errors. Otherwise, if the user is moving the mouse or using the
keyboard when the KVM switches to the next port, communication between
the computer and KVM Switch could be interrupted and cause erratic mouse
movement, or wrong characters to display when using the keyboard.
To disable AutoScan mode, press the space bar.
Connecting USB Devices to the Built-In 2-Port Hub
The KVM Switch includes a built-in 2-port USB v1.1 device hub that allows
you to connect two additional shared peripherals. When you connect any
USB device to the KVM Switch, that device can be accessed through
whichever computer you are currently using.
Note: This is not suitable for storage devices such as LS-120 drives and Zip®
drives because you cannot dynamically switch ports and disconnect a
mounted storage device when it is in use by the operating system. For
example, you are working on computer 1 with a file open that is stored on a
Zip drive connected to the KVM Switch. If you switch to computer 2 while
the file is still open, you will get a “file lost or corrupted” error message on
computer 1. The same will occur when you are using a streaming device
such as the Belkin VideoBus USB video capture device. You can switch from
one computer safely to the next, only if the VideoBus is no longer in use by
the first computer. You will notice that after the USB KVM switches to
another computer, the mouse remains inoperative for one or two seconds.
This is normal, and ensures that proper USB synchronization is established.
Enable AutoScan mode—#0 key

BELKIN KVM SWITCHES AND ACCESSORIES
17
OmniView KVM Switches
OmniView E Series
These KVM devices allow you to control two or four computers from one
console and make switching between computers more convenient.
Designed for compatibility with your PS/2 platform, they reduce desktop
clutter and provide a simple, reliable solution at a lower price point.
High-quality resolution of up to 2048x1536@85Hz is supported through
the E Series KVM Switch when used with coaxial VGA cabling, offering the
highest resolution without compromising the quality of the display. Power
for the KVM Switch draws off of the keyboard, meaning no power supply
is necessary and less cables to hassle with. Other standard features found
on this unit include: hot key functionality; PS/2 keyboard and mouse
emulations for error-free boot up; and a Belkin Two-Year Warranty.
F1DB102P E Series 2-Port KVM Switch, PS/2
F1DB104P E Series 4-Port KVM Switch, PS/2
OmniView SOHO Series with Audio
This innovative design provides built-in cable management and uses little
space while adding a whole new sculpted look to your desktop. The PS/2
KVM switch allows you to control up to four PS/2 computers from one
console. The greatest interface flexibility is yours with PS/2 and USB
switches. They offer you expanded compatibility with either interface, or
both, along with the additional convenience of direct-access port
selectors on the face of the switch. The USB KVM Switch offers support
for USB computers and consoles. It includes a built-in, 2-port USB device
hub that allows you to connect additional shared peripherals. Switch
between speakers and microphones without having to unplug and re-plug
them when switching computers. The flash feature allows users to
download firmware updates to ensure compatibility with the latest
computers and devices. The designed enclosure offers cable management
in a neat and convenient manner. High-quality resolution of up to
2048x1536@85Hz is supported by the SOHO Series KVM Switch when
used with coaxial VGA cabling, offering the highest resolution without
compromising the quality of the display. Other standard features found on
this unit include: hot key functionality; keyboard and mouse emulations
for error-free boot up; and a Belkin Five-Year Warranty.
F1DS102P SOHO Series 2-Port KVM Switch with Audio, PS/2
F1DS104P SOHO Series 4-Port KVM Switch with Audio, PS/2
F1DS102U SOHO Series 2-Port KVM Switch with Audio, USB
F1DS104U SOHO Series 4-Port KVM Switch with Audio, USB
F1DS102T SOHO Series 2-Port KVM Switch with Audio, PS/2 & USB
F1DS104T SOHO Series 4-Port KVM Switch with Audio, PS/2 & USB

BELKIN KVM SWITCHES AND ACCESSORIES
18
OmniView PRO2 Series with On-Screen Display
OmniView PRO2 Series KVM Switches deliver reliability, performance, and
centralized control necessary for today’s enterprise environment. This
series of KVM Switches enables you to control multiple platform servers
from a single console. Available in the desktop-style, 4-port, and the 19-
inch rack-mountable. 8- and 16-port models, the OmniView PRO2 Series
KVM Switch expands easily for full control of as many as 256 CPUs
through dedicated daisy-chain ports. Video resolutions of up to
2048x1536@85Hz are supported through a 400MHz bandwidth. On-
Screen Display allows you to name and select attached servers using an
on-screen interface. Switch between ports by using hot key commands or
direct-access port selectors. The PRO2 Series uses standard cables for
easy installation; includes a 12-volt DC, 1-Amp power supply; and is
backed by a Belkin Five-Year Warranty.
F1DA104T PRO2 Series 4-Port KVM Switch with On-Screen Display,
PS/2 & USB
F1DA108T PRO2 Series 8-Port KVM Switch with On-Screen Display,
PS/2 & USB
F1DA116T PRO2 Series 16-Port KVM Switch with On-Screen Display,
PS/2 & USB
OmniView MATRIX2 Series with Dual-Console Control
OmniView MATRIX2 Series 8- and 16-Port KVM Switches enable two
administrators to control up to eight or 16 PS/2 and USB platform
servers, separately or simultaneously. Each user operates a separate
console following a different bus path for complete independence from
the other console. The OmniView MATRIX2 Series KVM Switch expands
easily for full control of as many as 256 computers through dedicated
daisy-chain ports and is natively rack-mountable for server room
environments. Video resolutions of up to 2048x1536@85Hz are
supported through a 400MHz bandwidth. On-Screen Display allows you to
name and select attached servers using an on-screen interface. Switch
between ports by using hot key commands or direct-access port
selectors. The MATRIX2 Series uses standard cables for easy installation;
includes a 12-volt DC, 1-Amp power supply; and is backed by a Belkin
Five-Year Warranty.
F1DM208T MATRIX2 Series 8-Port KVM Switch with Dual-Console Control,
PS/2 & USB
F1DM216T MATRIX2 Series 16-Port KVM Switch with Dual-Console Control,
PS/2 & USB