Bell System bellagio User manual

Bell System (Telephones) Ltd.
PD–281 Issue 1 June 2016
bellagio
Digital
Audio Door Entry System
Installation & Operation Manual
This manual applies to the following: -
BFD-DIG Digital Door controller –Version 2 Build 3 and up
BS-LX Audio Phone
801 Audio Phone –Version 4 onwards
DBA-4I Phone Isolator
DBA-8Z Zone Isolator

bellagio Digital Entry System
PD–281 Issue 1 Installation and Operating Manual Page 2 of 52
801 Audio Phone
801 Deskphone
BS-LX Audio Phone
801 Deskphone
DBA-4I Phone Isolator
DBA-8Z Zone Isolator
BFD-DIG controller
Bellagio Entrance Panel

bellagio Digital Entry System
PD–281 Issue 1 Installation and Operating Manual Page 3 of 52
TABLE OF CONTENTS
Wiring diagrams.................................................................................................................4
Overview 1 –Full Isolation, 1 entrance up to 32 phones..................................................5
Overview 2 –Full isolation, 1 entrance 33 to 64 phones..................................................6
Overview 3 –Zone isolation, 1 entrance up to 32 phones ...............................................7
Overview 4 –Zone isolation, 1 entrance 33 to 64 phones ...............................................8
Overview 5 –System / Entrance interconnections...........................................................9
Diagram 6 –BFD-DIG PCB Detail .................................................................................10
Diagram 7 –Basic System Wiring Detail........................................................................11
Diagram 8 –Phone Connections (Zone Isolation)..........................................................12
Diagram 9 –Phone connections (Full Isolation).............................................................13
Diagram 10 –Isolator Interconnections (single PSU required).......................................14
Diagram 11 –Isolator interconnections (separate Power supply)..................................15
Diagram 12 –Entrance interconnections (BFD-DIG).....................................................16
Power Supply Requirements ..........................................................................................17
Cable Specification..........................................................................................................17
Cable Distances...............................................................................................................18
Installation & Commissioning ........................................................................................20
Checklist.........................................................................................................................20
Wiring.............................................................................................................................20
801 Audio Phone............................................................................................................23
BS-LX Audio phone........................................................................................................23
Commissioning................................................................................................................24
Settings..........................................................................................................................24
Testing / Connecting ......................................................................................................24
BFD-DIG Door Controller Settings.................................................................................25
BFD-DIG Door Controller Jumper Settings ....................................................................29
Door Speech Volume Adjustment ..................................................................................30
Bellagio Panel Option Settings.......................................................................................31
DBA-4I 4 Way Phone Isolator ........................................................................................32
DBA-8Z 8 Way Zone isolator..........................................................................................37
Phone settings ...............................................................................................................43
Troubleshooting ..............................................................................................................45
Common Faults..............................................................................................................45
Quick Fault Reference ...................................................................................................45
Specifications ..................................................................................................................48
Safety Information and Declarations..............................................................................51

bellagio Digital Entry System
PD–281 Issue 1 Installation and Operating Manual Page 4 of 52
Wiring diagrams
System
Full Isolation
Diagram Nos.
Zone Isolation
Diagram Nos.
1 Entrance,
Up to 32 ways
Overview 1
6, 7, 9, 10
Overview 3
6, 7, 8, 10
1 Entrance,
32 –64 ways
Overview 2
6, 7, 9, 11
Overview 4
6, 7, 8, 11
Multi-entrance
Up to 32 ways
Overview 1, 5
6, 7, 9, 10, 12
Overview 3, 5
6, 7, 8, 10, 12
Multi-entrance,
32 –64 ways
Overview 2, 5
6, 7, 9, 11, 12
Overview 4, 5
6, 7, 8, 11, 12

bellagio Digital Entry System
PD–281 Issue 1 Installation and Operating Manual Page 5 of 52
Overview 1 –Full Isolation, 1 entrance up to 32 phones

bellagio Digital Entry System
PD–281 Issue 1 Installation and Operating Manual Page 6 of 52
Overview 2 –Full isolation, 1 entrance 33 to 64 phones

bellagio Digital Entry System
PD–281 Issue 1 Installation and Operating Manual Page 7 of 52
Overview 3 –Zone isolation, 1 entrance up to 32 phones

bellagio Digital Entry System
PD–281 Issue 1 Installation and Operating Manual Page 8 of 52
Overview 4 –Zone isolation, 1 entrance 33 to 64 phones

bellagio Digital Entry System
PD–281 Issue 1 Installation and Operating Manual Page 9 of 52
Overview 5 –System / Entrance interconnections

bellagio Digital Entry System
PD–281 Issue 1 Installation and Operating Manual Page 10 of 52
Diagram 6 –BFD-DIG PCB Detail
5 E6 F7 G8 9 +31 RXTX12V
Keypad
Time
D
–
42
bell
BFD-DIG
free
Enhanced Speech
Door Controller
Display / Keypad
Status
1
1
Prog-6
HF Prog
Vol+
Speech
Vol–
Panel
Speaker
Save
Lock
Power
Test
Cam2 Audio
Video
100
75
High
100
75
High
Cam1 Cam2
4 3 2 1 0
Video
Gain
Label BFD-DIG
Version No
Build No
Panel
Tone
Volume
bell
System
© 2010
– – – – –
+++
Speech Unit
PM 12V SPKR
Exit 12V12VDoor Lock
+ + + + +
–––
Power
2 2M M 1 1S S B BA A
– ––– – – –
VideoCamera 1 Camera 2 Video 28VAudio AudioData DataCommn
+ + + + +
Input Output
+–

bellagio Digital Entry System
PD–281 Issue 1 Installation and Operating Manual Page 11 of 52
Diagram 7 –Basic System Wiring Detail

bellagio Digital Entry System
PD–281 Issue 1 Installation and Operating Manual Page 12 of 52
Diagram 8 –Phone Connections (Zone Isolation)

bellagio Digital Entry System
PD–281 Issue 1 Installation and Operating Manual Page 13 of 52
Diagram 9 –Phone connections (Full Isolation)

bellagio Digital Entry System
PD–281 Issue 1 Installation and Operating Manual Page 14 of 52
Diagram 10 –Isolator Interconnections (single PSU required)
For example 1 –32 ways

bellagio Digital Entry System
PD–281 Issue 1 Installation and Operating Manual Page 15 of 52
Diagram 11 –Isolator interconnections (separate Power supply)
For example 32-64 ways

bellagio Digital Entry System
PD–281 Issue 1 Installation and Operating Manual Page 16 of 52
Diagram 12 –Entrance interconnections (BFD-DIG)

bellagio Digital Entry System
PD–281 Issue 1 Installation and Operating Manual Page 17 of 52
Power Supply Requirements
The system is powered by 12V power supplies only: -
Model PS4 12V, 4A.
Model 840 12V, 4A battery backup supply.
Note 1. The PS4 power supply has been specifically designed to operate with the
requirements of the system. Bell System is unable to guarantee functionality or provide
support for systems which use third party power supplies.
Cable Specification
All system wiring must be carried out using Cat5 signal cable and where necessary 1mm²
(or greater) power cable as tabulated below. Cat5 cable has a known performance for the
transmission of data signals, whilst telephone or alarm cables are not suitable.
Bell System will be unable to offer any warranty or support for systems installed
using incorrect cables.
Cat5 Cable Specification
Cat5 is our short reference for EIA standard UTP Category 5 Unshielded Twisted Pair data
cable. This is a standard solid core twisted pair cable having 4 pairs (8-cores) and no
shield. The cores are in pairs where Blue and ‘Blue with a White stripe’ are twisted
together as the first pair. The other three pairs are similar with main colours Orange,
Green and Brown.
Also available and acceptable are:
UTP Category 5e (Cat5e)
UTP Category 6 (CAT6)
UTP Category 6e (CAT6e)
The exact cable can be chosen from the above on cost and availability grounds.
STP (Shielded Twisted Pair) cables are not recommended.
UTP “patch cables” are not recommended.
NOTE: Cat5 cable is easily identifiable as the specification is printed on the sheath

bellagio Digital Entry System
PD–281 Issue 1 Installation and Operating Manual Page 18 of 52
Cable Distances
Connection
No. of
cores
Cable
length
Core
Type
Phone connections
DBA-4I/8Z to 1 x 801, 801S or 801PS phone
5
70m
CAT5
DBA-4I/8Z to 2 x 801, 801S or 801PS phones (in
the same dwelling)
5
35m
DBA-4I/8Z to 1 x BS-LX phone
7
65m
DBA-4I/8Z to 2 x BS-LX phones
( in the same dwelling)
7
30m
Entrance to Control equipment (BFD-DIG Door controller)
Entrance Panel BGP-Audio
Also /PR, -LCP, LCP/PR
2x
8
50m
1.0 mm2
CAT5
PAX1 Fob reader (extra to any entrance panel)
+3
Lock release
0.5A
4
CAT5
1A
8
1A
2
1.0mm2
Exit button
2
CAT5
Door monitor contact / switch
2
System Interconnections
DBA-4I / DBA-8Z to Power Supply/BFD-DIG
8
**2
CAT5
BFD-DIG to BFD-DIG
+ Trades facility (optional)
6
+1
**1
Misc
Power Supply to BFD-DIG
2
3m
1.0mm2
TS2000-BST Time clock to BFD-DIG Door
controller (optional)
4
50m
CAT5
**1 There is no restriction on this distance, except, the maximum overall cable distance
between the furthest 2 points (entrance panel to phone via the control equipment)
on the system must not exceed 300m.
**2 Refer to the cable overview diagrams 1, 2, 3, 4 or 5
For larger cable distances please contact the manufacturer.

bellagio Digital Entry System
PD–281 Issue 1 Installation and Operating Manual Page 19 of 52
Compatible Phones
Model
Privacy of
Speech
Buzzer mute
Door open
indicator
Slide switch (on/off)
Button with indicator;
adjustable mute time
801
x
x
x
x
801S
x
√
x
x
801P
√
x
x
x
801PS
√
√
x
x
BS-LX
√
x
√
√
Phones connected to a DBA-4I Phone Isolator have privacy of speech inherent in the
design therefore models 801P and 801PS should not be used. All phones connected to
the same DBA-8Z Isolator must be the same model (a mixture of desk or wall mounting is
allowed).
As standard a maximum of two phones are allowed in each flat. Contact your distributor if
more are required.
The phones specified above are wall mounting. For a desk-mount model, add ‘–DESK’ to
any of the 801 phone series part numbers.
Phones can be supplied with a hearing aid induction loop fitted: add ‘-IDL’ to the part
number.
Privacy of Speech
Once a call has been initiated from an entrance panel only the phones which are ringing
may answer the call. The conversation cannot be overheard by another phone except an
extension phone in the same flat (i.e. one which had also been ringing). This feature is
available on systems with Full Isolation (all phone models) and on Zonal Isolation (801P,
801PS and BS-LX models only).
Extension sounders and flashing strobe
The RT27 extension sounder can be fitted instead of a 2nd phone and has a similar volume
level and sound to the 801 series phones.
The SG1 sound generator has an adjustable volume level and 8 different tones. The
volume is louder than an RT27, but requires an extra 12V DC power supply such as a
model 340C. This power supply should be fitted close to the SG1. There is a maximum of
3 units per flat.
A FB31 flashing beacon is also available for the hard of hearing. The device requires an
extra power supply such as the 340C which should be a short distance from the FB31.
There is a maximum of 3 units per flat.
Note it is not possible to have a DBA-4I or DBA-8Z Isolator phone output connected to just
extension sounders or a strobe, a phone must be present.

bellagio Digital Entry System
PD–281 Issue 1 Installation and Operating Manual Page 20 of 52
Installation & Commissioning
Checklist
The following checklist is a summary of what is required. Refer to the relevant pages for
further details.
●Review the section headed ‘Safety Information’ on page 51.
●Ensure that ‘Power Supply Requirements’ on page 17 have been understood.
●Confirm that Cat5 cable has been specified.
●Install the system according to instructions in this section.
●Check/set the door controller settings.
●Check/set the phone isolator jumper and switch settings.
Wiring
Refer to the diagrams from page 20 onwards as appropriate for the equipment you have.
All wiring is carried out using a mixture of Cat5 for the signal wiring and 1mm² (or greater)
cores for the power wiring; refer to Page Error! Bookmark not defined. for further details.
It is strongly recommended that a consistent colour code be used throughout such as that
indicated on the connection diagram. Certain signals must be interconnected using a
twisted pair from the Cat5 cable. These are clearly marked on the connection diagram
and should be strictly observed.
Door Controller
The door controller and power supply should be wall-mounted in a convenient cupboard or
other protected environment with available mains power. Cable length to the entrance
should be less than 50m. The door controller for the second and subsequent entrances
may be situated in the same location, or to meet the 50m requirement may be situated in
another location. Power supplies may be shared between door controllers placed in the
same location, but controllers in separate locations must be separately powered.
Phone Isolator
The Phone isolator(s) and power supply(ies) should be wall-mounted in a convenient
cupboard or other protected environment with available mains power. Cable length to the
hone should be less than 150m, see ‘Cable Distances’ page 18. In many cases the phone
isolators will be in the same location as the door controller(s), but they may be distributed
as required to reduce wiring distances. Power supply provision can be varied beyond the
tables above, for details see the alternate cabling supplements.
Gate Controller
The gate switch controller BSSW is wired between the block door controllers and the
phone isolators, so would normally be wall mounted next to a door controller.
For further details see the “bellissimo and Bellcall Manual Gate and Block (PD-120)”.