Belmont CLESTA eIII User manual

INSTALLATION INSTRUCTIONS
IMPORTANT
This manual provides installation instructions for the CLESTA eIII.
The instructions contained in this booklet should be thoroughly read and
understood before installing the chair and unit.
After the installation has been completed, keep this manual in a safe place and
refer to it for future maintenance.
DENTAL UNIT
H
BOOK NO. 1E03DRD0 (4E)
Printed in JAPAN 2014-07

TABLE OF CONTENTS
Page
1. Overview and Major Components---------------------------------------------------1
2. Dimensions and Specications
2-1. Unit Section Specications ---------------------------------------------------------------1
2-2. Unit Section Dimensions ------------------------------------------------------------------2
3. Installation Requirements ---------------------------------------------------------------3
4. Necessary Tools-------------------------------------------------------------------------------6
5. Installation Instructions
5-1. Unit Section Unpacking -------------------------------------------------------------------6
5-2. Chair Section Preparation for Installations-------------------------------------------8
5-3. Unit Section Preparation for Installations --------------------------------------------8
5-4. Mounting Cuspidor Unit to the Chair -------------------------------------------------9
5-5. Installation of Utility Section (Plumbing) -------------------------------------------- 10
5-6. Electrical Connections in the Utility Section----------------------------------------- 12
5-7. Installation of the Dental Light--------------------------------------------------------- 13
6. Installation of Accessories and Optional Parts
6-1. Drain Cap and Basket Strainer--------------------------------------------------------- 14
6-2. Cupller Nozzle and Bowlush Nozzle------------------------------------------------ 14
6-3. Assistant Arm Stopper-------------------------------------------------------------------- 14
6-4. DCI Syringe -------------------------------------------------------------------------------- 15
6-5. Attach the collar to the cart hose guide bracket (Cart type)---------------------- 16
6-6. Waste Receptacle (Optional) ------------------------------------------------------------ 16
6-7. Film Viewer (Optional)------------------------------------------------------------------- 16
6-8. Handpiece Flushout (Optional)--------------------------------------------------------- 17
6-9. Service Outlet (Water / Air)(Optional)------------------------------------------------ 17
6-10. Clean Water System (DCI Water Bottle)(Optional) ------------------------------ 18
6-11. DCI Water Bottle Cover (Optional) -------------------------------------------------- 18
6-12. Monitor Bracket (Optional) ----------------------------------------------------------- 19
7. Adjustment
7-1. Water and Air Stop Valves--------------------------------------------------------------- 20
7-2. Main Air Pressure ------------------------------------------------------------------------- 20
7-3. Main Water Pressure --------------------------------------------------------------------- 20
7-4. Handpiece Adjustment ------------------------------------------------------------------- 20
7-5. Instrument Holder Angle Adjustment --------------------------------------------- 21
8. Attach the Covers
8-1. Table Tray and Table Tray Mat -------------------------------------------------------- 21
8-2. Cuspidor Side Panel ---------------------------------------------------------------------- 21
8-3. Mounting Bracket Cover ---------------------------------------------------------------- 21
9. Unit Flow Diagram ------------------------------------------------------------------------ 22
10. Unit Electrical Diagram
10-1. 100V Type --------------------------------------------------------------------------------- 23
10-2. 200V Type--------------------------------------------------------------------------------- 24

H
Light Pole
Dental Light
Cuspidor Unit Section
Doctor Unit Section
Spittoon Bowl
Assistant Control Panel
Cuspidor Control Panel
Assistant Arm
Assistant Holder
Utility Box
Foot Controller
Doctor Table
Doctor Control Panel
Handpiece Holder
Dental Viewer
Balance Arm
Horizontal Arm
Cart Type
Over the Patient Type
Doctor Unit Section
Cart Base
Lock Knob
Caster
1. Overview and Major Components
2. Dimensions and Specications
2-1. Specications
Rated power supply : AC110V 50/60Hz AC120V 50/60Hz AC220V 50/60Hz
AC230V 50/60Hz AC240V 50Hz
Fuse : 110V 120V ....... 10A/125V
220~240V ......... 5A/250V
Air main pressure : 0.45 ~ 0.5MPa
Water main pressure : 0.1 ~ 0.2MPa
Weight : 70kg (Without dental light) Over the Patient Type
: 80.7kg (Without dental light) Cart Type
Dental Light : AL-501 Dental light
: 048 Dental light
Usage environment : Temperature +10ºC ~ +40ºC
Humidity 30% ~ 75%
Air pressure 700 hPa ~ 1060 hPa
Transportation / Storage environment : Temperature -20ºC ~ +70ºC
Humidity 10% ~ 95%
Air pressure 700 hPa ~ 1060 hPa
Service Life : 10 Years
Equipment that is not suitable for use in air, ammable anesthetic gas, oxygen or nitrous oxide.
- 1 -

2-2. DIMENSIONS
1210
1210
1407
610
650
829
1407
743
563
1050ࠤ
1300
518
460
750
ࠤ
1000

(With Light Pole)(Without Light Pole)
Unit : mm
Dimensional tolerance: ±10%
Over the Patient Type
- 2 -
Cart Type

3. Installation Requirements
General Requirements
(1) The contractor is to supply the necessary service and materials to complete the installation to the
satisfaction of the dentists and the installation engineer.
(2) This includes the supply and installation of the power source wires, air supply piping, water supply piping,
suction piping including suction control wires and drain piping as noted on page 5 for installation position
and plumbing layout.
Setting Requirements
(1) The CLESTA eIII dental unit comprises of a Chair section, Cuspidor unit section, Doctor table section
and Dental light section.
(2) The CLESTA eIII should be mounted taking the opening end of drain pipe (Installation reference point)
into due consideration. (See page 5 for installation position and plumbing layout)
(3) The area on which the CLESTA eIII is to be installed must have endurance force of 490kg/m2.
(4) The installation position of the CLESTA eIII is shown in page 5 for installation position and plumbing
layout as a recommended example.
Piping and Plumbing Requirements
(1) All piping and conduit for cables are to be laid under the oor and to come out from the oor in the
positions shown in page 5 for installation position and plumbing layout.
(2) The installation position and height from the oor of each pipe and cable conduit are shown in page 5
for installation position and plumbing layout.
(3) The recommended sizes, materials and end piece are shown in list below.
(4) Regarding installation of the vacuum pump and its connection to the main suction line, follow
the specications of central vacuum pump system manufacture's recommendation.
Item Material Size End
Piece
Compressed Air Supply Pipe Shock Resistance Out. Dia.18mm PT1/2
P.V.C. Pipe HI-13 In. Dia. 13mm
Water Supply Pipe Shock Resistance Out. Dia.18mm PT1/2
P.V.C. Pipe HI-13 In. Dia.
13mm
Suction Pipe P.V.C. Pipe VP-20 Out Dia.
26mm
IN. Dia.
20mm
Drain Pipe P.V.C. Pipe VP-50 Out. Dia.58mm
In. Dia.
50mm
Power Supply Cable Conduit P.V.C. VE-16 In. Dia.
16mm
Vacuum Control Wire Conduit P.V.C. VE-16 In. Dia.
16mm
Note : The suction pipe and drain pipe should be laid under the oor with an inclination of 1/200 - 1/400.
Air vacuum type does not require suction pipe, vacuum control wire and its conduit.
- 3 -

- 3 -
Air Supply Requirements
(1) Compressed air to be supplied should be ltered.
Dirt and moisture in the air may cause trouble in unit air system.
(2) Air Pressure
Regulate the outlet air pressure of the compressor to the utility box at 0.5-0.7MPa (5.0-7.0kg/cm2)
and the air pressure should be kept between 0.45-0.5MPa (4.5-5.0kg/cm2) in the utility box at any time.
(3) Compressed Air Supply Capacity
Central vacuum type . . . at least 60 l/min.
Air vacuum type . . . at least 100 l/min
Water Supply Requirements
(1) The supply water should be clean.
Dirty water may cause trouble in unit water line.
(2) Regulate the water pressure of the water supply to the utility box at 0.2-0.4MPa (2.0-4.0kg/cm2) for
operating unit efciently. The water pressure should be kept between 0.1-0.2Mpa (1.0-2.0kg/ cm2) in the
utility box at any time.
(3) Amount of water
Central saliva ejector type . . . at least 5 l/min.
Water saliva ejector type . . . at least 7 l/min
Electric Supply Requirements
(1) The connection of the power supply cable is to be carried out in accordance with the local electrical
regulation.
(2) Capacity of the power supply (Include the CLESTA eIII Chair)
110/120V Type Single Phase 50/60 Hz : 10A
220V Type Single Phase 50/60 Hz : 5A
230V Type Single Phase 50/60 Hz : 5A
240V Type Single Phase 50Hz : 5A
(3) Power supply line should be provided with fuses or circuit breaker in accordance with power
consumption.
(4) The earth wire (ground wire) should be proved in the utility box.
(5) All cables should have at least 500mm surplus from the oor so that they are long enough to
be connected to the terminals in the utility box.
- 4 -

Base Plate
Drain
(Installation
reference point)
Drain (Installation reference point)
min.300
20
30
40
40
PT1/2
30
40
20
30
40
PT1/2
40
±
5
2700
min.1000 min.800
300
410
110
55
135
160
2700
min.1000 min.800
min.300
70 70
220
280
110
55
135
70 70
220
280
Base Plate
Vacuum Pipe
Power Source
Water Supply
Vacuum
Operating Wire
Drain (Installation
reference point)
Air Supply
Air Supply
Vacuum Pipe
Power Source
Water Supply Drain (Installation
reference point)
Vacuum Operating Wire
Power Source •
Vacuum Operating Wire
Floor Line
Drain (Installation reference point) Vacuum Pipe
Water
Supply
Air Supply
Floor Line
Drain (Installation reference point)
Vacuum Operating Wire
Water
Supply
Vacuum Pipe
Power Source
Air Supply
Vacuum Pipe
Air Supply Power Source
Vacuum Operating
Wire
Drain
Water Supply
Dimensional
tolerance : ±5mm
Detail of piping size
min.528
min.988
40
±
5
30
±
5
20
±
5
Partition
Installation Position and Plumbing Layout (Central Vacuum Type)
Air vacuum type does not need vacuum pipe, vacuum operating wires and conduit.
Place the Utility box Vertically
(Under the Cuspidor)
Place the Utility Box Horizontally
(Front of the Chair Base)
- 5 -
Unit : mm
Dimensional tolerance: ±10%

- 5 -
4. Necessary Tools for installation
The following tools are necessary to assembling this product.
- 6 -
5. Installation Instructions
5-1. Unit Section Unpacking
1. Remove all wood screws xing the carton to the pallet and lift up to remove the carton.
Mats
Mats
Mats
Wood screw
No.
1
2
3
4
5
6
7
8
9
10
11
12
13
Name of Tools Qty.
Phillips head screwdrivers #2~ #4 1 pc./each
Flat head screwdriver 1 pc.
Precision screwdriver set (Phillips head / Flat head) 1 set
Adjustable wrench 1 pc.
Water pump pliers 1 pc.
Open end wrench set (5.5 ~ 24mm) 1 set
Allen wrench set (1.5 ~ 8mm) 1 set
Socket wrench set (8~22mm) 1 set
Long nose pliers 1 pc.
Diagonal pliers 1 pc.
Wire stripper 1 pc.
Wire crimp tool 1 pc.
Blade knife 1 pc.

2. Open the boxes that contain parts and check the contents of each box with the accessory parts list
attached to the parts box and with below list. Make sure to use provided parts such as screws, joints, and
stainless exible pipes that are used to mount the chair or for plumbing in the utility box.
Also, check the necessary parts for installing the option by referring to the below list. Refer to the
section 6: Installation of Accessories and Optional Parts instruction.
There are many small parts for optional kit that are packed in the plastic bag with option name label.
- 7 -
No.
1
2
3
4
5
6
7
8
9
10
No.
1
2
3
5
4
No.
1
No.
1
2
3
4
5
6
7
8
9
Utility Box (Plumbing) Parts / Unit fixing parts
Description Purpose / Location of use Qty.
Spring washer M10 Unit fixing 4 pcs.
Nut M10 Unit fixing 4 pcs.
Hex head bolt M10 x 30 Unit leveling 4 pcs.
Wood screw M3.5 x 20 Utility box fixing 4 pcs.
Vacuum elbow Utility box plumbing (Central vacuum) 1 pc.
Drain elbow Utility box plumbing (Central vacuum) 1 pc.
Drain joint (Optional) Utility box plumbing (Air vacuum) 1 pc.
Drain bush (Optional) Utility box plumbing (Insert to drain pipe) 1 pc.
Stop valve (Water / Air) Utility box plumbing 2 pcs.
Stainless flexible pipe Utility box plumbing 2 pcs.
Qty.
Waste receptacle & Bracket Waste receptacle 1 pc./each
Light pole washer & Connectors (3 pcs.) Dental light 1 pc./each
Cover hose clamp, pan head screw M3 x 16,
Nut M3 Syringe (Assistant side) 1 pc./each
Collar, Pan head screw M4 x 35, Cap nut Cart hose guide bracket 1 pc./each
Flat head screw M5 x 15 Table tray (Large size) 4 pcs.
Optional Parts
Monitor bracket
1 set
Optional Kit
EMS Scaler assembling Kit EMS scaler
1 set
SP-4055 (P-Max) scaler assembling lit SP-4055 (P-Max) scaler 1 set
SP-4055 NEWTRON scaler assembling kit SP-4055 NEWTRON scaler 1 set
VARIOS170 scaler assembling kit VARIOS170 scaler 1 set
CAVITRON scaler assembling kit CAVITRON scaler 1 set
Handpiece flush-out assembling kit Handpiece flush-out 1 set
Air service outlet assembling kit Air service outlet 1 set
Water service outlet assembling kit Water service outlet 1 set
DURR CS1 assembling kit DURR CS1 1 set
Description Purpose / Location of use
Description Purpose / Location of use
Description Purpose / Location of use
Qty.
Qty.
Unit Parts
Monitor rotation shaft, Washer, Bottom cover,
Truss screw M4 x 12 (2 pcs.), Set screw M6 x 8
(2 pcs.), Hex cap bolt M5 x 8 (2 pcs)
Assistant arm stopper,
M10 Spring washer Mounting bracket 1 pc./each
6

Be sure to remove the carriage bolt from the chair before lift the chair by upper structure.
This could cause damage to the chair if operate the chair without removing the carriage bolt.
CAUTION
5-3. Unit Section Preparation
1. Remove two wood screws xing the utility box to the pallet.
2. Remove four cuspidor unit xing screws (M10 x 65 at head screw) and hold the cuspidor unit.
Four at head screws are used when x the cuspidor unit to the chair.
M10 x 65
Flat head screw
- 8 -
5-2. Chair Section Preparation
1. Remove the carriage bolt from the chair.
* Refer to the chair installation manual for preparation of the chair.
* Do not attach the backrest and seat section until the unit installation has been completed.
Carriage bolt
(with red tag)

5-4. Mounting Cuspidor Unit to the Chair
1. Raise the dental chair to the highest position.
2. Mount the cuspidor unit on the mounting bracket of the chair and x with four M10 x 65 at head screw
which xed cuspidor unit to the pallet, and M10 spring washer, M10 Nut.
Adjust the level of the cuspidor unit with four M10 x 30 level adjustment hex head bolt as needed.
M10 Nut
M10 x 65
Flat head screw
M10 Spring washer
M10 x 30
Hex head bolt
Chair side
mounting bracket
Cuspidor side
mounting bracket
After mounted the cuspidor unit on the chair, please confirm that the cuspidor
unit does not hit to the utility box when move the chair to lowest position.
- 9 -

- 9 -
5-5. Installation of Utility Box (Plumbing)
1. Install the water stop valve and the air stop valve to each supply pipe.
The positioning of the stop valves are shown in page 5 for Installation Position and Plumbing Layout.
2. Fix the utility box to the oor with four M3.5 x 20 wood screws.
- 10 -
- Air Vacuum Type -
1) Cut the drain hose and vacuum hoses at suitable length and connect them to drain joint (Optional)
with plastic glue (Pipe solvent).
Note : The Drain hose should be sealed with silicone sealant or taping.
2) Insert the drain joint (Optional) into drain pipe.
Note : The Drain pipe should be sealed with silicone sealant or taping.
Attaching drain bushing (Optional) to the drain pipe is desirable, and drain joint should be
bonded rmly into the drain pipe.

M3.5 x 20
Wood Screws (4 pcs.)
3. Drain Hose and Vacuum Hose Connection
- Central Vacuum Type -
1) Cut the drain hose and vacuum hoses at suitable length and connect them to each elbow
with plastic glue.
Note : The Drain hose should be sealed with silicone sealant or taping.
2) Insert the drain hose elbow and vacuum hose elbow into each pipe.
Note : The Drain pipe should be sealed with silicone sealant or taping.
Attaching Drain Bushing (Optional) to the Drain Pipe is desirable, and Drain Elbow should be
bonded rmly into the Drain Pipe.
Drain Bush
(Optional)
Drain Pipe
Vacuum Pipe
Drain Hose
Vacuum Hose
Drain Elbow Vacuum Elbow
Connect with
plastic glue
Connect with
plastic glue
Drain Hose
Vacuum Hose Drain Joint
(Optional)
Drain Pipe
Drain Bush
(Optional)
Connect with
plastic glue

Stainless Flexible Pipe
Water stop valve
Air stop valve
Vacuum elbow
Drain elbow
Air filter
Water filter
Filter
Seal
(Packing)
Stop Valve
Be careful not to bend
flexible pipe to acute angle.
(Less than radius of 50mm)
4. Water and Air Supply Line Connection
1) Bend each stainless exible pipe to a suitable angle for easily connectable between water/air
stop valves and water/air lters. (See gure below)
2) Connect the stainless exible pipe with rubber seal to water/air stop valves and tighten it securely using
the adjustable wrench. Be careful not to pinch the rubber seal when connect it.
Rubber seal
Stop valve
Stainless flexible pipe
Adjustable wrench
Rubber seal
Stainless flexible pipe
Adjustable
wrench
Filter
Water pump pliers
3) Connect the stainless exible pipe with rubber seal to lters and tighten it securely using the adjustable
wrench and water pump pliers. Be careful not to pinch the rubber seal when connect it.
5. Cart Type
1) Connect the umbilical hose to the utility box and connect the tubings from cuspidor unit to the utility
parts. For air vacuum type, does not have the green turbing (φ4 x 6).
2) Connect the blue (2 x 4) tubing with barb tting and black (1.2 x 2) tubing with barb tting.
Blue tubing • • • Small size master valve in the cuspidor ~ Doctor table water line
Black tubing • • • Shuttle valve of the cupller in the cuspidor ~ Cupller switch of the doctor table
Umbilical hose
Yellow (4 x 6)
Blue (6.5 x 10)
Green (4 x 6)
Orange (2 x 3.7)
Air switch
(Vacuum operating)
Tubings from
doctor table
Tubings from
cuspidor unit
Blue (2 x 4) with
barb fitting
Black (1.2 x 2) with
barb fitting
Air switch
(Main switch)
Blue (2 x 4)
Black (1.2 x 2)
- 11 -

5-6. Electrical Connections in the Utility Section
* Be sure turn off the breaker of the power source line and main switch before connect the wirings.
Be sure to connect the earth wire into the utility frame.
1. Connect the central vacuum operating wires to the terminal block.
(This connection is central vacuum type only. The Air vacuum type does not have this connection.)
* How to connect terminal block
1) Cut the vacuum operating wires at suitable length with a diagonal pliers.
2) Cut the exterior insulation of the vacuum operating wires about 10mm using the wire stripper.
3) While pressing the slot of the terminal with a small head at head screwdriver, insert the wire to the
terminal and release the screwdriver. Make sure that the wire is connected securely.
4P Connector
(Signal line for
chair safety)
4P Connector
(Signal line for chair safety)
9P Connector
(Chair operating wire) 9P Connector
(Chair operating wire)
Chair power
supply cable
Chair power supply
cable with plug
Earth
Socket
Brown
Light blue
-100V Type- -200V Type-
Brown
Black Black
Black Black
WhiteWhite White
White Light blue
White
Black
Unit power supply plug
Vacuum
Operating wire
Wires
(Yellow)
Flat head screwdriver
Wire
Terminal block
10mm
Cut the wires
with diagonal pliers
Strip the wires
with wire stripper
2. Connection of the chair power supply cable
-100V Type-
Connect the plug of the chair power supply cable to socket in the utility box.
Connect the unit side connectors (4P and 9P) the chair side connectors (4P and 9P) in the utility section.
-200V Type-
Connect the chair power supply cable to the terminal block in the utility box. Connect the earth wire of the
power supply cable onto the utility frame with M4 screw. (M4 screw is attached on the frame)
Connect the unit side connectors (4P and 9P) the chair side connectors (4P and 9P) in the utility section.
3. Connect the unit power supply plug into the suitable power supply line in the utility section.
The power supply plug may not be able to use depending on the countries. Use a plug adapter or replace
a plug to plug it into the power supply line.
- 12 -

5-7. Installation of the Dental Light
1. Put washer (φ28.8 x φ40.5) on the light pole. Pass the light cable through the light pole and
attach the dental light section to the light pole. Fix the light section and light pole with M5 x 8 set screws
using the 5mm allen wrench. (Set screws are attached onto the light pole)
Dental light section
Light pole
Washer
Light cable
H
Set screw
M5 x 8 (4 pcs.)
Wires from
dental light
Main post
Connector
Wires from
cuspidor unit
H
Set Screw
M6 x 18 (2 pcs.) Set screw
M6 x 8 (2 pcs.)
Cable from
dental Light
Connector
Cable from unit
Insert the wires into
groove of the connector.
Pinch the inner cover with
long nose pliers.
Long nose pliers
Hold the outer cover of
the connector and attach
it to the opposite side
groove.
Groove
From dental light
From unit
Light Blue
(Blue)
Brown
(Brown)
Yellow/Green
Earth
White
(Light Blue)
Black
(Brown)
Yellow/Green
Earth
2.Connect the wires from the dental light and wires from the cuspidor unit one by one with connectors
using the long nose pliers.
See the gure below for color of the wires from the dental light and the unit.
Insert the light pole to the main post and x with two M6 x 18 and
two M6 x 8 set screws using the M6 allen wrench (Set screws are attached onto the main post).
- 13 -

- 13 -
6. Installation of Accessories and Optional Parts
* Refer to the Final Assembly File (FAF) for installing the handpiece and separator.
* Do not attach the covers until the installation has been completed (Wiring, tubing connection and
accessories, optional parts installation). The small size table tray and the cuspidor side panels are attached
to the unit at the factory. Remove the small size table tray and cuspidor side panel as follows.
Drain cap
Basket strainer
Spittoon bowl
Cupfiller nozzle
Bowlflush nozzle
Nut
6-2. Cupller Nozzle and Bowlush Nozzle
Insert the cupller nozzle and the bowlush nozzle to the spittoon bowl and tighten each nut by hand.
- 14 -
6-1. Drain Cap and Basket Strainer
Fit the drain cap and the basket strainer in the spittoon bowl.


Table chassis
M5 x 15
Flat head screw
Table tray
(Small size)
- How to open the table tray -
- How to open the cuspidor side panel -
Cuspidor side panel
Cuspidor side panel
Side panel fixing screw
Flat head
screwdriver
Loosen the side panel
fixing screw by flat head
screwdriver and open it
outward
6-3. Assistant Arm Stopper
The assistant arm stopper is not attached to the mounting bracket due to the packaging restrictions.
Attach the assistant arm stopper by using the 17mm spanner until M10 spring washer becomes at.
Be careful not to over tighten the screw, it may break the screw.

M10 Spring washer
Assistant arm stopper

- 15 -
Membrane panel
M4 x 12
Sems screw
Needle Valve
for Syringe
Air
(Yellow cap)
Water
(Blue cap)
Syringe
Gray
Air
Water
Needle valve
for syringe Connected in
factory
Connected in
factory
Table chassis
Cover hose clamp
M3 x 16
Pan head screw
M3 Nut
6-4. DCI Syringe
- Doctor Table side -
1. Unscrew the six M4 x 12 sems screws and remove the membrane panel from the doctor table.
2. Pass the syringe tubing through to the table chassis and insert the syringe tubing to the cover hose clamp.
3. Connect the syringe tubings to the needle valve (Water and Air) as shown in gure.
* Air tubing and water tubing are both gray color. Connect the air supply to the syringe tubing to
conrm which is the air line before connect the needle valve.
4. Tighten the M3 x 16 pan head screw with M3 nut of the cover hose clamp to x the syringe hose.
5. Set the syringe into the handpiece holder.
6. Fix the membrane panel on the table with same screws.
Water
(Blue cap)
Needle valve
for syringe
Syringe
Gray
Needle valve
for syringe
Air
Water
Master valve
set (Small size)
Connected
in factory
Connected
in factory
Air
(Yellow cap)
M3 Nut
Cover Hose clamp
Tube
M3 x 16
Pan head screw
- Assistant side -
1. Pass the syringe tubings through the hole of the cuspidor front panel and x it with cover hose clamp,
M3 x 16 pan head screw and M3 nut.
2. Connect the syringe tubings to the needle valve (Water and Air) as shown in gure.
* Air tubing and water tubing are both gray color. Connect the air supply to the syringe tubing to
conrm which is the air line before connect the needle valve.
3. Tighten the M3 x 16 pan head screw with M3 nut of the cover hose clamp to x the syringe hose.
4. Set the DCI syringe into the assistant holder.

Nut
Waste Receptacle
Waste Receptacle Bracket
Adjustable Wrench
6-6. Waste Receptacle (Optional)
Fix the waste receptacle bracket to the doctor table with M10 nut using the adjustable wrench.
Put the waste receptacle into the waste receptacle bracket.
6-7. Film Viewer (Optional)
1. Remove the two M4 x 15 sems screws from under the table chassis using the #2 phillips head screwdriver.
2. Pass the lm viewer cable through to the table chassis as shown in gure.
Fix the lm viewer to the table chassis with two M4 x 15 sems screws.
Follow the same procedures for panorama viewer.
Film viewer
Cable
M4 x 15
3A Sems screw
Table chassis
Cable
M4 x 15
3A Sems screw
- 16 -
6-5. Attach the Collar to the Cart Hose Guide Bracket (Cart type)
Due to the packing, did not attach the following collar to the guide bracket at the factory.
Attach the collar to the cart hose guide bracket with M4 x 35 pan head screw and cap nut using the #2
phillips head screwdriver.
M4 x 35
Pan head screw
Collar Cap nut

- 17 -
6-8. Handpiece Flushout (Optional)
* Make sure to use the ushout assembling kit.
Fix the ushout switch to the table chassis.
Direction of the ushout switch is on direction for front side and off direction for rear side of the table
chassis.(See gure)
Keep the dismounted parts after replaced from kit installation for future maintenance
 
 
Flushout switch
Table chassis
(Front Side)
(Rear Side)
Air
Coolant air
(From foot
controller) Auto select valve
T Joint
Gray
Clear ( 2 x 3.7 200mm)
Flushout switch
Pullback Valve
Air manifold
Shuttle Valve
 
Ｗ
Ｄ
Ｃ
Ｐ
ON
OFF
Flushout switch
fixing hole
Washer, Nut
(Come with
flushout switch)
Gray ( 2 x 3.7 200mm)
Gray ( 2 x 3.7 200mm)
Gray ( 2 x 3.7 200mm)
Gray ( 2 x 3.7 200mm)
Replace plug
for 1/4 barb fitting
Replace 1/8 barb
fitting for plug
Connected
at factory
To be
connected on site


6-9. Service Outlet (Water / Air)(Optional)
* Make sure to use the service outlet assembling kit (Water/Air).
Fix the service outlet and needle valve on the cuspidor panel and connect the tubings as shown on the
following gure.
Keep the dismounted parts after replaced from kit installation for future maintenance.
Service outlet
(Water)
Service outlet
(Air)
Service outlet
(Water)
Service outlet
(Air)
Needle Valve
(Water)
Master Valve
set (Small)
Cuspidor
panel
Master Valve
set (Small)
T-joint
Air
Service outlet
(Air)
* With clean water system specifications
Cut the air tubing
and connect
with T-Joint
Needle Valve
(Water)
Remove the
Hole Plug Yellow
( 4 x 6 400mm)
Blue
( 4 x 6
350mm)
Blue
( 4 x 6
200mm)
Connected at factory
To be connected on site
Connected
at factory
To be connected
on site
Replace plug
for 1/4 barb fitting
Yellow
( 4 x 6 350mm)