Belmont Voyager III User manual

DENTAL UNIT AND CHAIR
0197
Thank you for purchasing TAKARA BELMONT product.
Please read through this instruction manual carefully before using the product to ensure proper
use. Failure to read the instruction manual before use may lead to an accident.
After the installation has been completed, keep this instruction manual near the product for
future maintenance. Refer this manual as needed.
If you have any questions about this Manual or this product, please contact us.
If manual becomes unreadable or is lost, please request a new manual by contacting your dealer.
Installation should be conducted by authorized personnel only.
Follow instructions on installation manual.
2015-08 (FE)
BOOK NO. 1E04SDAE
OPERATING INSTRUCTIONS

INTENDED USE OF THE PRODUCT
SYMBOLS
SAFETY PRECAUTION (Please observe safety precautions fully)
OVERVIEW AND MAJOR COMPONENTS
LOCATION OF THE LABELS
OPERATIONS / FUNCTIONS
CARE AND MAINTENANCE
STORAGE/LIFETIME/CONSUMABLE PARTS/STOCK PERIOD OF PARTS
BEFORE ASKING FOR REPAIRS
DIMENSIONS AND SPECIFICATIONS
MAINTENANCE AND INSPECTION
ELECTROMAGNETIC COMPATIBILITY (EMC)
LIST OF COMPATIBLE HANDPIECES
LIST OF COMPATIBLE DENTAL LIGHT
DECLARATION OF CONFORMITY
1 ~ 9
10
11
12 ~ 25
26 〜31
32
33
34
35 〜37
38 〜39
40
41
42
10
TABLE OF CONTENTS

This product is an active therapeutic device intended for the exclusive use for diagnoses, treatments and
relative procedures of dentistry. The product must be operated or handled by the qualified dentists or
by dental staffs under the supervision of the dentist. Such dentists or dental staffs should instruct and/or
assist the patients to approach to and leave from the product. Patients should not be allowed to operate
or handle the product unless he/she is so instructed. The product is supplied together with the handpieces
like electric micromotor, air turbine and/or motor, scaler and so on.
Compliance with Directives
Voyager III compliance with the following directives,
Medical Device Directive 93/42/EEC, RoHS Directive 2011/65/EU.
In case of disposal of equipment
When disposing the unit, appropriately dispose complying with all current applicable regulations and
local codes. In EU area, EU directive on waste electrical and electronic equipment (WEEE) is applied on
this product. In this directive, environment conscious recycling/abandonment is obligated.
Disposal of residue material
Please request a special contractor when you dispose amalgam.
Connectable handpieces for this product
Use the compatible handpieces as shown on the attached list for this unit.
Compatibility of Dental Light
This unit should be combined with the dental light described in the list of compatible dental light.
Important Notes
In case of the trouble, please contact a Takara Belmont ofce or your dealer.
Do not disassemble or attempt to repair.
Installation and repair should be conducted by authorized personnel only.
No modication is allowed except handpiece installation by authorized dealer technician.
Attempts at disassembly, repair or modications may lead to abnormal operation and accidents.
Environmental Requirements
Usage environment
Ambient Temperature : 10 to 40ºC
Humidity : 30 to 75%
Atmospherical Pressure : 700 to 1060 hPa
Transportation / Storage environment
Ambient Temperature : -20 to +70ºC
Humidity : 10 to 95%
Atmospherical Pressure : 700 to 1060 hPa
Equipment is not suitable for use in environments with, ammable anesthetic gases, oxygen or nitrous
oxide.
INTENDED USE OF THE PRODUCT

Chair manual
control
Protective earth
(ground)
ON (power) OFF (power)
EC REP
Chair last
position
Chair auto
return Chair preset 1 Chair preset 2
To raise
the chair
To recline
the backrest
To lower
the chair
To raise
the backrest
To raise
the chair
To lower
the chair
To recline
the backrest
To raise
the backrest
Air
Water Service outlet
(air)
Service outlet
(Water)
Manufacturer
Syringe Date of
manufacture
Non-ionizing
radiation
Separate collection
for electrical and
electronic
equipment
General warning
sign
Caution
Authorized
representative in
the European
community
Refer to
instruction
manual/booklet
Reference
number
Serial Number
Alternating
current
Comply with
MDD,93/42/EEC
Type B
Applied Parts
Autoclave Symbol
This symbol on component means that the
component can be sterilized with an autoclave
at 135 max.
Symbol Description Symbol Description Symbol Description Symbol Description
SYMBOLS
In this manual, on the labels, on the control panel of Voyager III, following symbols are used.
Conrm the meaning of each symbol.

This symbol indicates that “it is recommended to follow these precautions
for safety.”
Classification of precautions Severity and degree of imminence of possible injury or damage
WARNING
CAUTION
NOTICE
This symbol indicates that “ignorance of these precautions may lead to severe
injury or even death as a result of improper use.”
This symbol indicates that “ignorance of these precautions may lead to mild
or moderate physical injury or damage to property as a result of improper use.”
WARNING
1. Be sure to turn off the breaker for the equipment in the clinic when this product will not be used for a
long period of time
Be sure to turn off breakers for equipment in the clinic when this product will not be used for a long period of time
(following the completion of work, during the suspension of business, etc.). Insulation degradation may cause electrical fire.
2. Be sure to turn off the main switch upon completion of work or during work breaks
Be sure to turn off the main switch upon completion of work or during work breaks. This prevents incorrect operation
due to accidental contact and associated hazards.
3. Never disassemble, repair or modify this product
Individuals other than certified repair technicians should not disassemble or attempt to repair and modify this product.
This could lead to an accident, failure, electric shock or fire.
4. Be sure to establish a grounding connection
Be sure to establish a proper grounding connection. (Refer to a vendor for grounding connection.) Failure or electric
leakage may lead to electric shock.
5. Use with caution in the presence of electromagnetic interference waves
Do not place this product around equipment generating electromagnetic waves (including communications equipment,
elevators, etc.) as incorrect operation of this product may occur in the presence of electromagnetic interference waves.
Do not use equipment generating electromagnetic waves, such as mobile phones, around this product.
6. Be sure to turn off the main switch when a high frequency surgical instrument (HF-Surg) is used.
Use of a HF-Surg may cause the equipment to malfunction due to generated noise. Be sure to turn off the main switch when
using the HF-Surg.
7. Use with caution on patients with a cardiac pacemaker
Use this product with extreme caution on patients with a cardiac pacemaker. In the case of any abnormalities in patients
during use, immediately turn off this product and discontinue use.
8. Handling of equipment in the case of a power failure
If the chair stopped at elevated position, chair will not go down. Help a patient to get off from the chair while paying attention
to avoid patient’s injury. Pay attention the chair doesn’t fall down. When power comes back after power failure, to avoid
unexpected movement, follow below instructions.
• Turn off the main power switch on dental unit.
• Put the handpieces in the holder.
1
SAFETY PRECAUTIONS (Please observe safety precautions fully)
Before use, read the “Safety precautions” carefully to ensure proper use.
The following information is designed to ensure safe use of this product and to prevent injury and damage
to you and others. The precautions contained here are classied depending on the severity and degree of
imminence of possible injury or damage resulting from improper use. Be sure to follow all the information,
which is important for safety.

2
WARNING
9. Immediately wipe off any water spills or leakage on the floor
Immediately wipe off any water spills or leakage on the floor. This could cause damage to the product, decreased strength of
the floor may lead to physical injury including fall, or property damage.
In the case of water leaking from the unit, discontinue use, turn off the water main valve, main switch, breaker and contact
the dealer or our company.
10. When water leaking from the unit
Do not place objects weighing 3 kg or more on the Doctor's table. This could cause damage to the Doctor's table, defective
function or accidents.
12. Do not place an undue load on the arm
Do not get on or place an undue load on the table arm, cuspidor arm, assistant arm of this unit. This could cause the unit to
topple or other accidents.
13. Use the turbine with a water check valve
Use the turbine with a water check valve. Contact the dealer or our company when a turbine without a water check valve
will be used.
14. Do not sit on other than seat
When the backrest is at the forward position. Do not sit on or place an undue load on the headrest or legrest of dental chair.
This could cause the unit to topple or could damage the unit.
• Failure to maintain this product may lead to physical injury or property damage.
• Refer to maintenance section in this manual.
• Be sure to use the mirror cover of the IO5000 and 701 dental lights when the light is turned on. Direct contact with lamps
may cause burns.
• See the Instruction Manual of the dental light for further information.
• Be sure to turn off the power when replacing the IO5000 and 701 dental light. This could result in electric shock.
• Use only dedicated halogen lamps.
• Immediately after a halogen lamp has burnt out, the lamp and the lamp holder are still hot. Replace the lamp after
they cool down.
• Do not touch halogen lamps with bare hands.
• See the Instruction Manual of the dental light for further information.
11. Do not place objects weighing 3 kg or more on the Doctor's table
15. Ensure the maintenance of this product
16. Be sure to use the mirror cover
17. Be sure to turn off the power when replacing lamps
18. Prohibition of maintenance
During operation, repair and maintenance are prohibited.
SAFETY PRECAUTIONS (Please observe safety precautions fully)

3
CAUTION
Only dentists or other dental professionals should use this product.
Before use, confirm that the parts are correctly and safely operating and that there are no obstacles around this product.
3. Close the water main valve and turn off the main switch upon completion of work
Be sure to close the water main valve and the main switch at the end of each workday to prevent water leakage from occurring.
Keep your eyes on patients (especially, children) so that mischief or inadvertent operation of equipment will not lead to
unexpected accidents.
4. Pay attention to patients and children
5. Precautions for handling synthetic leather
Stain caused by clothing dyes
The synthetic leather of this product may become stained by direct contact with clothes or belts. If there is stains, wipe clean
as quickly as possible with a 10% detergent solution diluted using water to prevent permanent staining. In case the synthetic
leather is wiped with a wet cloth, fully wipe off the moisture with dry cloth.
Take care of deformation or stains due to direct contact
• Direct contact with other objects such as plastic products, painted items, solvents or adhesive tape may cause changes to the
surface luster, cracking, deformation or peeling.
• Direct contact with newspaper or printed paper may cause stains.
• Direct contact with items of clothing such as printed images of T-shirts, or jeans may cause discoloration of the synthetic
leather of this product.
• Direct contact with solvents such as benzene nail polish remover, alcohol may cause discoloration, melting of the surface,
elution of the plasticizing agent, changes to surface luster, hardening/softening or peeling.
• Using bleach or bleached sheets may cause changes to surface luster or discoloration.
• Installing this product next to sources of excess heat such as irons or heaters may cause deformation or discoloration.
• Protect this product from direct sunlight by installing curtains. Failure to follow this instruction may cause changes,
shrinking, discoloration or fading of the leather surface.
• Placing heavy objects for a long period of time may leave an imprint of wrinkles on the synthetic leather that cannot be
removed.
1. Only experienced personnel should use this product
2. Confirm safety before use
7. Precautions for sterilization
Do not sterilize besides the procedures that we provide. This could cause damage to the unit.
8. Discontinue use if you feel that “something is wrong”
Always be careful to inspect this product for looseness, rattling, tilting, wobbling, sounds, temperature, odors, etc.
Immediately discontinue use at the first feeling that “something is wrong.”
9. Read the documents accompanying the various pieces of equipment
Before use, be sure to carefully read the package inserts and Instruction Manuals accompanying the various
pieces of equipment to ensure proper use.
10. Precautions when using water other than tap water
The water unit is intended for use with tap water. Caution should be exercised as the use of water other than
tap water (water through a sterilizer of water systems, etc.) may result in failure of equipment.
11. Do not smack or rub this product
Do not smack or rub this product forcefully. This could cause damage to covers or defective function.
Do not place any hard and heavy article or any article having a sharp tip or edge on the chair’s
seating area. The synthetic leather may be damaged otherwise.
6. Pay attention of the seating area
SAFETY PRECAUTIONS (Please observe safety precautions fully)

4
CAUTION
12. Be sure to operate switches with your hands
Be sure to operate switches with your hands, except the foot controller, which is operated with your foot.
Operation with body parts other than hands may cause damage or incorrect operation.
Immediately release any auto mode switches (1, 2, 0, LP) after depressing them, because when any auto mode switches are
depressed more than 5 seconds, the chair position will be set up to preset with buzzer sound.
13. Be careful when operating chair auto mode switches (1, 2, 0, LP)
・Confirm that the patient is seated in the proper position before operation of the chair and keep your eyes on the patient
during operation.
・Please make sure there are no children around a dental chair except a patient. Keep children off from a dental chair except a
child patient gets dental procedures.
・Before operating the chair, confirm that there are no obstacles around this product.
・Be careful that the stool will not be caught in the gap between the chair backrest. Damage to the backrest or stool may occur.
・Confirm that there are no obstacles between the base and pump cover. This could cause damage to the pump cover or
accidents.
14. Keep your eyes on the patient during operation
・During headrest operation, confirm that the patient’s headrest is in proper position and keep your eyes on the patient during
operation.
・Do not set a headrest at the position where a patient feels a pain.
・The headrest will be come off from the backrest in case of pulling too much.
・Do not allow hands, fingers or hair to become entangled in the moving parts of the headrest or between the headrest and
backrest section during operation.
15. Pay attention during the headrest operation
・Before rotating the armrest, confirm that there are no obstacles around the armrest.
・Do not operate the chair with the armrest swing out 90 degrees. Confirm that the armrest is locked position (normal position)
before operating chair.
・Do not place objects on the table during table height adjustment.
・Turn off the main switch before adjusting the table height.
・Be sure to slide down the collar on the lock ring after removing the lock ring.
・Please confirm whether a table is fixed. If the table is not fixed surely, it causes a fall and the accident during operation.
17. Cautions at adjusting the Dr table height
19. Do not place anything hot on the unit
Do not place anything hot on the unit. This could cause deformation or discoloration.
20. Put a cover on the scaler tip
After use, be sure to put the dedicated tip cover (if a cover comes with the unit) on the scaler in the holder.
If the cover is not used, injury from the scaler tip may occur.
・Pay attention to surroundings when you move the Doctor's table. Injury by the tips of handpieces, etc., may occur.
・Be sure to move the Doctor's table by holding the handle of the unit.
21. Precautions for use of handpieces
Handpieces may have poor spraying performance or generate heat due to the lack of cooling water/cooling air.
In the case of the development of heat or an odor of something burning, immediately discontinue use and contact the dealer
or our company because burns may occur or dental pulp may be adversely affected.
22. Handling of the syringe
Be careful not to drop the syringe. Otherwise, it may break or the syringe may deform.
16. Pay attention during the armrest rotation
18. Pay attention during movement of the Doctor's table
SAFETY PRECAUTIONS (Please observe safety precautions fully)

5
SAFETY PRECAUTIONS (Please observe safety precautions fully)
CAUTION
・Before use, check that the nozzle will not come off from the syringe. Do not use if the syringe nozzle comes loose.
・Make sure that the nozzle is tightened securely and will not come off when pressing the spray button. Do not use if the
syringe nozzle comes loose.
・Do not subject the unit to shock. Doing so check that the nozzle will not come off from the syringe.
Cleaning must be done within 1 hour after use.
Replace with a new syringe nozzle and saliva ejector tip and do not take autoclave for following cases.
・Any waste material can not be removed by clogged hole.
・Contamination and solid material attached to vacuum handpiece and saliva ejector can not be removed.
・Sterilization by class B cycles.
・Skip the drying process if the temperature is to exceed 135°C.
・The cap, filter and body are made of resin. They may become deteriorated if they are sterilized in an autoclave many times.
・After autoclave sterilization, the cap, filter, body and valve are subject to discoloration, which does not have a negative
effect on performance.
・The slide knob can be autoclave 100 times and is expendable supplies.
・Sterilization temperature is 135 degrees or less.
・If damage occurs to the sterilization pouch, discard and sterilize again using a new pouch.
・For cleaning, do not use cleaning agents containing solvent or abrasives, thinners or oil-based alcohol
(butanol and isopropyl alcohol), which may cause cracks. Clean with a wet soft cloth or use a mild detergent diluted to an
approximately 10% solution. Wipe off water and residual disinfectant immediately.
・This could cause corrosion, damage or incorrect operation of the unit. They may facilitate rust generation.
Should drug solution or water come into contact with this unit, immediately wipe it off with a dry soft
towel, etc. This could result in defective function or electric leakage as well as spotting or rusting.
・Flow rate adjustment knobs for water and air are intended to increase/decrease the flow rate. Caution should be exercised
as tuning the knob excessively may cause it to turn free.
・There is cupfiller flow rate adjusting screw (pinch valve) for maintenance. The flow rate is adjusted when installing the unit.
・Do not spray liquids directly onto the surfaces of the holder. In order to prevent damage to electrical components and system.
Wipe off the holder surface with soft cloth moistened with cleaner or disinfectant. Wipe off with dry soft cloth to dried up
of the holder after cleaning and disinfection.
・Completely dried up the cleaning solution before use the product.
23. Precautions for after using of the syringe
Clean the filter with running water. Do not use brush to clean the filter which may damage to the filter.
・After use, wipe off syringe nozzle, body contaminated with blood or saliva and clean it with cleaning agent as necessary.
・Sterilization with autoclave, be sure to use sterilization pouch.
・For cleaning of other syringes, observe the instructions shown in the package inserts and instruction Manuals included with
the syringes. Before use, be sure to carefully read the package inserts and instruction manuals accompanying the various
pieces of equipment (including optional articles) to ensure proper use.
24. Precautions after the cleaning of syringe
25. Precautions for cleaning of the solid corrector
26. Precautions for cleaning the syringe nozzle, saliva ejector tip
27. Use of flow rate adjustment knobs
28. Precautions for sterilization of syringe nozzle, saliva ejector tip
29. Precautions for cleaning the product exterior
30. Immediately wipe off drug solution when it comes into contact with this unit
31. Precautions for cleaning the Dr. instrument holder and the assistant holder

6
SAFETY PRECAUTIONS (Please observe safety precautions fully)
CAUTION
• Never use sandpaper, metal scrub brushes or abrasive cleaning agents to clean the spittoon bowl.
• Do not use strongly acidic cleaning agents or alkaline pipe cleaning agents, which may cause corrosion of metals, etc.
• Be careful not to apply unnecessary force to it when cleaning. (Be careful not to hit or drop it.)
33. Precautions for cleaning of the spittoon bowl
32. Precautions for cleaning the vacuum and saliva ejector line
Do not use strongly acidic cleaning agents or alkaline pipe cleaning agents, which may cause corrosion of metals, etc.
34. Precautions for cleaning the vacuum hose, saliva ejector hose
The vacuum and saliva ejector hose can be disconnected by pulling them down for cleaning. Turn off the main switch
of the unit before cleaning the hoses.
35. Do not use water other than purified water, distilled water or pure water for the water tank
・The water tank is intended only for use with purified water, distilled water and pure water.
・Do not use mouthwash or electrolyzed water, such as ConCool or povidone iodine, as they may cause clogged tubing or
affect internal valves and equipment.
Adjust the air supply pressure for the water tank to 200 kPa or less. An excessively high pressure may cause damage to the
water tank.
37. Precautions for right/left handed conversion
・Make sure read through pages 25 for instructions before perform with right and left handed conversion. This could cause
physical injury or property damage.
・Take care not to contact the doctor table to the cuspidor during conversion.
・Take care not to pinch the vacuum hose and saliva ejector hose between the assistant arm and the cuspidor swing arm during
this conversion.
36. Set the pressure of the water tank at 200 kPa or less

7
SAFETY PRECAUTIONS (Please observe safety precautions fully)
NOTICE
With no air supplied, this product does not operate even after turning on the main switch. Turn on the power of the compressor
before operating this product.
Check operation of the compressor
Troubleshooting and contact information
In the case of any problems, discontinue use, turn off the main switch and contact the dealer or our company.
Use dental film viewer / Panoramic film viewer
・Turn off the viewer when the viewer is not in use.
・Dental film viewer / panoramic film viewer are intended to be used for aiding observations, and should not be used for
diagnostic purpose.
When lift up the headrest lever to unlock position (Single articulating headrest)
Push the headrest forward while lift the headrest lever, headrest section moves smoother.
Ensure the maintenance and inspection of this product
Refer to the section of maintenance and inspection.

8
SAFETY PRECAUTIONS (Please observe safety precautions fully)
Practice the ush out of water retained in the unit at the beginning of each workday to maintain the quality of
dental treatment water and ensure a steady supply of water to handpieces.
After this unit has not been used for a long period of time (at the beginning of the week, in the morning,
etc.), water retained in the hose inside the unit or water heater will create an environment where unwanted
bacteria are likely to grow. In order to ensure safe treatment and untroubled operation of handpieces, practice
the ush out of the unit water line at the beginning of each workday.
It is recommended that ush out of water inside the unit and hose of handpieces should be performed with
fresh water at the end of morning office hours and at the end of each workday to inhibit the growth of
unwanted bacteria.
Handpiece line
Turbine
Air Motor
Scaler
Syringe (Both Doctor' s and Assistant's)
Cuspidor line
Cup ller (water heater)
Bowl ush
Approximately ve minutes for water changing in the
cup ller line.
Handpiece line
Pick up handpieces from the holder one at a time,
leave the turbine untouched and remove the bar
from the motor and hold the motor over the spittoon
bowl. (When the ush out function is active, pick
up all handpieces in clusters and hold them over the
spittoon bowl.)
Cuspidor line
Cupller (water heater)
Bowl ush
Approximately 40 seconds per turbine, air motor, scaler
and syringe (approximately 40 seconds when ush out
of all of them is performed at the same time.)
PRACTICE OF FLUSH OUT
Standard time required for ush out of the unit water line
Perform ush out of the scaler with it attached to the
main unit. Otherwise, a malfunction may be caused.
PROCEDURE OF FLUSH OUT
Without Flushout Function
Press the foot controller to ush out of the
handpiece water.
With Flushout Function
Pick up the handpieces then turn on the flush out
switch to ush out the handpiece water.
The water lled to the cup, then drain the water
of the cup to ushing out the cupller water.
Repeat it 7~8 times.
CAUTION
CAUTION
PRECAUTIONS FOR WATER QUALITY

9
1
2
3
4
5
6
7
8
3
SAFETY PRECAUTIONS (Please observe safety precautions fully)
Caution Points During Operation of the Product
Description of Symbol Marks
Caution areas such as moving parts, rotating parts and detachable parts to which caution should be paid.
Caution areas that are provided with an emergency stop mechanism.
Be aware of contact with the assistant’s
instrument holder.
Ensure that the upper body of the patient does
not go beyond the armrest into the cuspidor unit.
Take care not to be trapped by moving
parts of the backrest.
Do not put hands or feet into the gap between the
backrest and the seat.
Take care not to be trapped by the armrest.
Do not operate the chair with the armrest swing
out 90 degrees.
Take care not to be trapped by moving
parts of the headrest.
Do not allow hands, ngers, or hair to become
entangled in the moving parts of the headrest.
1
2
3
4
5Take care not to be trapped by the lower part of the
seat.
Do not put hands or feet into the gap in the lower part
of the seat.
Check the locking mechanism of the primary arm.
Check that, when moving the instrument table to the
back of the backrest, the chair lock indicator on the
doctor control panel blinks red, and operation of the
chair is halted.
Be aware of interference between the chair and the
table.
Do not move the table under the moving parts of the chair.
Take care not to be trapped between the sub link
cover and the base plate
Do not allow feet or obstruct between the sub link cover
and the base plate.
6
7
8

10
Pressure Gauge (Air)
Drain Valve
Water Main Valve Fuse Holder
Pressure Gauge (Water)
Cuspidor Unit
Doctor Unit
Instrument Holder
Foot Controller
Cuspidor Bowl
Assistant Holder
Doctor Arm
Backrest
Headrest
Doctor Table
Solids Collector
Armrest
Foot Switch
Handle
OVERVIEW AND MAJOR COMPONENTS
1. Overview and Major Components
1-1. Overview
1-2. Junction Box Section
Water main valve
Turn clockwise to open and counterclockwise
to close.
Drain Valve
Drains the water collected at the air filter on
the main water supply line.
Fuse Holder
• The main fuse of units is built-in.
• If you are replacing a fuse, please replace to
turn off the MASTER Switch / power switch
of this product.
• The capacity of the fuse is listed on the left
side of the fuse.

11
LOCATION OF THE LABELS
CAUTION - Electric shock
hazard, do not remove cover.
Refer servicing to qualified
service personnel.
F5A/250V
Caution label
Type B Applied
Parts Seal
Manual reference label
Type B Applied
Parts Seal
Type B Applied
Parts Seal
Label for Cuspidor needle
MAINS
Main mark (MAINS)
Power display label ( I ) ( O )
Fuse label (F5A/250V)
2015
FUSE
2. Location of the Labels
Labels are located on the product as below.

12
OPERATIONS AND FUNCTIONS
MAIN
ON
OFF
MASTER Switch
Master Switch
Indicator
Cuspidor Unit
Air Button
Lock Ring
Water Button
Syringe Tip
MAIN
ON
OFF
Flow Control
Screw (Water)
Decrease
Increase
Flow Control
Screw (Air)
Hex Key Wrench
MAIN
ON
OFF
Handpiece Spray Water
Control Knobs
ON OFF
3. Operation
With no air supplied, this product does not operate
even after turning on the main switch. Turn on the
power of the compressor before operating this
product.
NOTE
3-1. Master Switch
Turn on the master switch located under the doctor
table, the master switch indicator located on the front
side of the cuspidor unit turns to green.
Be sure to turn off the main switch upon
completion of work or during work breaks.
This prevents incorrect operation due to accidental
contact and associated hazards.
WARNING
3-2. Doctor Unit
(1) Handpiece Spray Water Flow Control Knobs
The handpiece is actuated by picking it up from the
handpiece holder and operating the foot controller.
Operation of the each handpieces, please refer to the
manufacturer's instruction manual attached to the
individual equipment. The handpiece spray water ow
control knobs are located under the doctor table provide
for individual adjustment. Each handpiece spray water
flow control knob is lines up from the facing left
hand side HP1, HP2 . . . Turning a ow control knob
counterclockwise increases flow volume and turning
clockwise decreases.
(2) 3-Way Syringe
A- 3-Way Syringe Operation
Depressing either or both buttons, this syringe offers
air, water and spray. Syringe tip can be rotated freely.
To remove syringe tip : Keep depressing the lock ring
and pull out the syringe tip.
To set syringe tip : Keep depressing the lock ring, insert
the syringe tip and release the lock ring.
B. 3-Way Syringe Flow Control Screw
Air and/or water ow of 3-way syringe can be adjusted
by the ow control screws located bottom of the table.
Facing right hand side screw controls air and left hand
side controls water.
Turning a ow control screw counterclockwise increase
flow volume and turning clockwise decrease. Use the
hex key wrench supplied.

13
Cupfiller Button
Bowl Flush
Control Knob
Decrease
Increase
Chip Blower Button
Coolant Water On/Off Switch
Drive Air Pedal
Vacuum Tip (Optional)
Slide Knob
Slide Knob
Open
Close
Open
Close
ON
OFF
3-3. Cuspidor Unit Section
(1) Cupller
Keep pressing the cupller button until a cup is
lled with water.
(2) Bowl Flush
Turn the bowl ush control knob counterclockwise,
water ushes into the cuspidor bowl.
Further turning counterclockwise, increases the
amount of ush water.
3-4. Assistant Instrument Holder Section
(1) Vacuum Handpiece
Suction begins when the vacuum handpiece is taken
out of the instrument holder. Opening or closing the
slide knob can control the suction flow rate. In case
of the central vacuum system, suction will not stop
immediately after the vacuum handpiece was returned
to the instrument holder, but suction will continue for
about 3 seconds by the function of delay circuit.
(2) Saliva Ejector Handpiece
Suction begins when the saliva ejector handpiece is
taken out of the instrument holder. Suction stop
immediately when the saliva ejector handpiece is
returned to holder. Opening or closing the slide knob
can control the suction ow rate.
3-5. Foot Controller
(1) Drive Air Pedal
Depressing the drive air pedal controls handpiece
rotation speed. If you require coolant water from
handpiece, turn on the coolant water On/Off switch
before pressing drive air pedal.
(2) Coolant Water ON/OFF Switch
Spray water ON/OFF switch allows water to be turned
on or off. Refer to 3-2 (1) of this manual for adjusting
water of each handpiece.
(3) Chip Blower Button
By depressing the chip blow button, chip blower
comes out from handpiece without bur turning.
(4) Safety Device by Foot Control
When the drive air pedal is being depressed and
handpiece is running, all the chair control switches
are inactivated. This is to prevent the chair from
unexpected movement by any switch being touched
accidentally.
OPERATIONS AND FUNCTIONS

14
OPERATIONS AND FUNCTIONS
Upward
Downward
Doctor Table
Collar
Lock ring
Groove for
height adjustment
Front Arm
Brightness control dial
ON
OFF
Switch
Switch
3-6. Doctor Arm
Table Height Adjustment
• Doctor table height can be adjusted 3 positions.
• Hold and slightly lift up the doctor table, stopper ring
will come up on upper swing arm post. Slide up or
down the stopper ring to appropriate groove on upper
swing arm post. Lower the doctor table to x it at that
height. Please conrm that a table is xed to the lower
course surely then.
3-7. Doctor Table Safety Lock Device
If excess pressure (upward or downward) is applied to
the doctor table by the movement of chair, safety device
stops the chair movement to protect the table from
being damaged.
3-9. Panoramic Film Viewer (Optional)
• The screen light (LED light source) is lit when the
switch is turned to the upper position (ON), and
the screen light (LED light source) is off when the
switch is turned to the lower position (OFF).
• The screen brightness increases when the brightness
control dial is turned upward, and the screen
brightness decreases when the brightness control
dial is turned downward.
•
Turn off the light when the lm viewer is not in
use.
• Dental lm viewer is intended to be used for
aiding observations, and should not be used for
diagnostic purpose.
NOTE
NOTE
•
Turn off the light when the lm viewer is not in
use.
• Panoramic lm viewer is intended to be used for
aiding observations, and should not be used for
diagnostic purpose.
3-8. Dental Film Viewer (Optional)
The screen light is lit when the switch is pressed, and
the screen light is off when the switch is pressed again.
WARNING
Do not place objects weighing 3 kg or more on the
Doctor's table. This could cause damage to the
Doctor's table, defective function or accidents.

15
OPERATIONS AND FUNCTIONS
ᅸງ゛䛴⾪♟䛒㻕㻓㻓㼎㼓㼄䜘㉰䛎䛰䛊
䜎䛌䛱シᏽ䛝䛬䛕䛦䛛䛊䚯
Ἰណ
CITY/BOTTLE
Select Switch
Pressurization
ON-OFF Switch
Water Bottle
1
2
3
AB
* Be careful it has a
sharp edge
3-10. Waste Receptacle (Optional)
• Replace the paper cup 2removing from the holder 1
when waste accumulates.
• The stainless waste receptacle may be detached
when it is turned in direction A. It is fastened when
turned in direction B. The lid has sharp portions
that can easily catch cotton, etc. Be very careful
when cleaning it.
3-11. Clean Water System (Optional)
• The water bottle CITY/BOTTLE select switch can
be changed between municipal water and water bottle.
CITY . . . . . Tap water
BOTTLE . . . Water bottle
• When the pressurization ON-OFF switch is set to ON,
the water bottle may be used.
CAUTION
The water tank is intended only for use with
puried water, distilled water and pure water.
Do not use mouthwash or electrolyzed water, as
they may cause clogged tubing or affect internal
valves and equipment.
3-12. Tray (Optional)
Use it for keeps standard set on the tray.
3-13. Sub Tray (Optional)
Use it for keeps cotton containers.
3-14. Cotton Containers (Optional)
Use it for keeps clean cotton.