Belmont Phot-X II 303 User manual

·Floor Mount Type..................FK1/FK2
·Mobile Type ...........................FM
·Room Mount Type..................RK
MODEL 303
DENTAL X-RAY
INSTALLATION
INSTRUCTIONS
This X-ray equipment may be dangerous to patients and operators
unless safe exposure factors and operating instructions are observed.
WARNING
R
0508(REV.0)

-1-
INDEX PAGE
SECTION 1 : TECHNICAL DATA
[1] ELECTRICALAND RADIATION DATA--------------------------------------------------- 2
[2] OVERALL VIEW AND MAJOR COMPONENTS ---------------------------------------- 3
[3] PHYSICAL DIMENSIONS-------------------------------------------------------------------- 5
[4] TUBE HEAD THERMAL CHARACTERISTICS ----------------------------------------- 6
SECTION 2 : PRE-INSTALLATION INSTRUCTIONS
[1] SUPPORT REQUIREMENTS ---------------------------------------------------------------- 7
[2] ELECTRICAL REQUIREMENTS ----------------------------------------------------------- 7
SECTION 3 : INSTALLATION INSTRUCTIONS
[1] INSTALLATION REQUIREMENTS -------------------------------------------------------- 8
[2] INSTALLATION OF FK1/FK2 TYPE ------------------------------------------------------- 8
[3] INSTALLATION OF FM TYPE ------------------------------------------------------------- 12
[4] INSTALLATION OF RK TYPE ------------------------------------------------------------- 14
[5] HEAD ASSEMBLY INSTALLATION------------------------------------------------------ 16
[6] MAIN CONTROLLER INSTALLATION-------------------------------------------------- 17
[7] SUB CONTROLLER INSTALLATION ---------------------------------------------------- 19
[8] HAND EXPOSURE SWITCH (OPTION) ------------------------------------------------- 20
SECTION 4 : POST INSTALLATION INSPECTION
[1] FK1/FK2 TYPE--------------------------------------------------------------------------------- 21
[2] FM TYPE ---------------------------------------------------------------------------------------- 22
[3] RK TYPE ---------------------------------------------------------------------------------------- 22
[4] HEAD POSITIONING ------------------------------------------------------------------------ 23
SECTION 5 : CONTROL IDENTIFICATION AND OPERATION
[1] MAJOR COMPONENTS AND CONTROL IDENTIFICATION----------------------- 23
[2] FUNCTION OF CONTROLS ---------------------------------------------------------------- 24
[3] OPERATING PROCEDURES --------------------------------------------------------------- 26
[4] HAND EXPOSURE SWITCH --------------------------------------------------------------- 26
[5] ERROR CODES-------------------------------------------------------------------------------- 27
[6] MAINTENANCE ------------------------------------------------------------------------------ 28
SECTION 6 : POST INSTALLATION CONFIRMATION
[1] CONFIRMATION OF POWER SUPPLY VOLTAGE ------------------------------------ 29
[2] CONFIRMATION OF TUBE POTENTIALAND COMPENSATION VALUE ------ 29
[3] CONFIRMATION OF TUBE CURRENT ------------------------------------------------- 29
[4] CONFIRMATION OF EXPOSURE WARNING LAMP & BUZZER ----------------- 30
[5] CONFIRMATION OF LINE VOLTAGE REGULATION ------------------------------- 30
SECTION 7 : INITIAL SETTING
[1] SPEED SETTING FOR FILM AND DIGITAL IMAGING------------------------------ 31
[2] PRIORITY OF SELECTIONS --------------------------------------------------------------- 32
[3] ELECTRONIC CHIME ON/OFF ------------------------------------------------------------ 33
APPENDIX 1 : CIRCUIT DIAGRAM------------------------------------------------------------ 33
This manual provides information and instructions for the installation, assembly calibration and
certification procedures for BELMONT PHOT-X II MODEL 303 dental x-ray.
The instructions contained in this book should be thoroughly read and understood by dealer service
personal before attempting to install the X-ray unit. After installation is completed, owners should
file this manual and refer back to it to schedule periodic maintenance.
CAUTION

-2-
[ 1 ] ELECTRICAL AND RADIATION DATA
1. X-ray tube --------------------------------------------------Toshiba D-0711 (StationaryAnode)
a. Focal spot------------------------------------------------0.7 mm
b. Target Material------------------------------------------Tungsten
c. Target angle ---------------------------------------------16˚
d. Maximum anode heat content ------------------------7kJ (10kHU)
2. Maximum x-ray tube assembly heat content ----------120kJ (170kHU)
3. Rated peak tube potential --------------------------------60 kV / 70 kV selectable
4. Rated tube current -----------------------------------------4 mA / 7 mA selectable
5. Maximum rated peak tube potential -------------------- 70 kV
6.
7. Power line frequency ------------------------------------- 50/60Hz,Single Phase
8. Exposure time----------------------------------------------0.01 ~ 3.2 sec.
9. Inherent filtration------------------------------------------1.7 mm Al Equivalent
10. Added filtration ------------------------------------------- 0.3 mmAl
11. Minimum filtration permanently in useful beam -----2.0 mm Al Equivalent at 70 kV
12. Nominal roentgen output 60 kV 70 kV
4 mA 7 mA 4 mA 7mA
a. Distal end of regular cone ----------------------------- 5.4 9.4 7.1 12.4 mGy/sec. ±40%
b. Distal end of long cone -------------------------------- 2.4 4.2 3.1 5.5 mGy/sec. ±40%
(Data obtained by direct measurement in the useful beam)
13. Nominal electrical output of H.V. generator ----------0.49 kW at 70 kV, 7 mA
14. Cone Source to skin distance Field size
a. Regular cone -------------------------------------------- 203 mm 58 mm dia., circular
b. Long cone (option) ------------------------------------- 305 mm 58 mm dia., circular
c. Rectangular cone (option) ----------------------------- 203 mm 36 x 47 mm, rectangular
15. Maximum symmetrical radiation field ---------------- 60 mm dia. at distal end of cone
16. Leaking technique factor --------------------------------70 kV / 0.14 mA
(0.14 mA is maximum rated continuous
current for 7 mA with a duty cycle 1 : 50)
17. Duty cycle ------------------------------------------------- 1 : 50 (0.5 sec. exposure with 25 sec. interval)
18. Maximum deviation of tube potential, tube current and exposure time
a. Below 0.1 sec. setting----------------------------------±10 kV, ±2 mA, ±5 msec.
b. 0.1 sec. setting & up ----------------------------------- ±5 kV, ±1 mA, ±10 msec.
19. Measurement base of technique factors
a. peak tube potential ------------------------------------- Average of peak tube potentials during
one exposure
b. tube current----------------------------------------------Average of tube current during one exposure
c. exposure time -------------------------------------------Time period during x-ray is emitted
20. Half value layer -------------------------------------------1.5 mm Al over
21. Source to the base of cone distance -------------------- 94 mm
22. Environmental condition for storage------------------- -20 ~ 70˚C, 10 ~ 100%, 500 ~ 1060hPa
23. Environmental condition for operation ---------------- 10 ~ 40˚C, 30 ~ 70%, 700 ~ 1060hPa
SECTION 1 : TECHNICALDATA
Rated Line Voltage [Vac] 100 110 120 220 230 240
Minimum Line Voltage [Vac] 90 99 108 198 207 216
Maximum Line Voltage [Vac] 110 121 132 242 253 264
Rated Line Power [kVA] 1.1 1.2 1.3 1.5 1.5 1.6
Rated Line Current at 70kV,7mA [Aac] 10.8 10.8 10.8 6.6 6.6 6.6
Maximum Line Current at 70kV,7mA [Aac] 12 12 12 7.3 7.3 7.3
(Internal Resistance [Ω] ) (0.18 ~ (0.20 ~ (0.22 ~ (0.97 (1.02 (1.06
0.44) 0.49) 0.53) max.) max.) max.)
Range of Line Valtage Regulation [%] 2 ~ 5 2 ~ 5 2 ~ 5 0 ~ 3 0 ~ 3 0 ~ 3

-3-
[ 2 ] OVERALLVIEWAND MAJOR COPMPNENTS
qMain Power Switch
wX-Ray Head
eCone
rYoke
tArm Collar
yBalance Arm
uHorizontal Arm (300mm)
iPole Bush
oBack Supporter
!0 Pole
!1 Base Cover
!2 Mounting Plate
!3 Main Controller
!4 Sub Controller
!5 Hand Exposure Switch
1. FOOR MOUNT TYPE (FK1/FK2)
2. MOBILE TYPE (FM)
qMain Power Switch
wX-Ray Head
eCone
rYoke
tArm Collar
yBalance Arm
uPole Bush
iPole
oPole Base
!0 Leg Bar (long)
!1 Leg Bar (Short)
!2 Lock Caster
!3 Standard Caster
!4 Main Controller
!5 Sub Controller
!65 Hand Exposure Switch
C
T1 T5
T2 T3 T4
FD
P
kV
60 70
mA
ab
4 7
INC
INC
CUS & PM
CUS
& PM
MLR OCC
MLR BW
8
8
6
9
13
14
15
6
1
1
10
11
12
7
14
15
7
9
10
11
12
23
4
23
4
5
513
C
T1 T5
T2 T3 T4
FD
P
kV
60 70
mA
ab
4 7
INC
INC
CUS & PM
CUS
& PM
MLR OCC
MLR BW
FK1Type FK2Type
C
T1 T5
T2 T3 T4
FD
P
kV
60 70
mA
ab
4 7
INC
INC
CUS & PM
CUS
& PM
MLR OCC
MLR BW
8
7
6
23
4
5
9
10
11
12
13
11
10
14
15
16
1
Fig.1-1 Overrall view and Major Components for FK1/FK2
Fig.1-2 Overrall view and Major Components for FM

-4-
Fig.1-3 Overrall view and Major Components for RK
3. ROOM MOUNT TYPE (RK) qMain Power Switch
wX-Ray Head
eCone
rYoke
tArm Collar
ySwing Arm 1
uSwing Arm 2
iSliding Post
oColumn Cover
!0 Colum
!1 Backrest Cushion
!2 Seat
!3 Gas Pump
!4 Base Plate
!5 Main Controller
!6 Sub Controller
!7 Hand Exposure Switch (Option)
Fig.1-4 Main Power Switch & Sub Controller Switches
qSub Controller Frant Panel !0 Cone Type Selection Switch
wReady Light !1 Film Speed Selection Switch
eExposure Time Adjusting Switch (Down) !2 Digital Imaging Switch
rExposure Time Adjusting Switch (Up) !3 kV Selection Switch
tTooth Selection Switch (T1) !4 mA Selection Switch
yTooth Selection Switch (T2) !5 Patient Size Selection Switch
uTooth Selection Switch (T3) !6 Exposure Time Display Window
iTooth Selection Switch (T4) !7 Exposure Warning Light
oTooth Selection Switch (T5) !8 Exposure Switch
4. SUB CONTROLLER
C
T1 T5
T2 T3 T4
FD
P
kV
60 70
mA
ab
4 7
INC
INC
CUS & PM
CUS
& PM
MLR OCC
MLR BW
3
1
4
5
6
7
2
8
9
10 11 12 13 14
15
17
18
16
1
2
4
5
6
7
8
9
10
12
13
14 15
3
11
16 17
C
T1 T5
T2 T3 T4
FD
P
kV
60 70
mA
ab
4 7
INC
INC
CUS & PM
CUS
& PM
MLR OCC
MLR BW

-5-
[ 3 ] PHYSICAL DIMENSIONS
Fig.1-5 Dimensions
600˚
1335 96 Max. 692
200
155
360
90
300˚
Max. 1190
Stroke 1100
Max. 1364
Max. 2123
Max. 1718 Stroke 1100
38
71 206
FK1
FK1
300 80
220˚ 220˚
600˚
90
300˚
775
Stroke 200
Stroke 700
450
126
571 80
106
400 350
130 260
500
500
180˚ 260˚
90
300˚
600˚
680
Max. 1190
Stroke 1100
Max. 1064
Max. 692
Max. 2027
Max. 1612 Stroke 1100
Max. 2147
1335
155360
536 200
90
825
80˚
38
71
206
[UNIT : mm]
PHOT-XII FM Mobile Type PHOT-XII FK1/FK2 Floor Type
PHOT-XII RK Room Type
Focal Spot Marking
Reference Axis
SSD
SSD
+ 158 mm
160 mm
SSD (Source to Skin Distance) :
a. Regular cone----------203 mm
b. Long cone-------------305mm
c. Rectangular cone-----203 mm

-6-
[ 3 ] TUBE HEAD THERMALCHARACTERISTICS
A. Interval between each exposure
The temperature inside of the tube head rises when an exposure is made. The value of the heat
generated is measured in Heat Units (HU), which is the product of tube potential, tube current
and exposure time. Excessive heat will accumulate inside of the tube head if the x-ray is used
without a proper cool down interval between each exposure. The excessive heat may damage the
x-ray tube, high voltage generator or both.
B. Duty cycle
A cool down interval of 50 seconds or more must be allowed between each 1 second exposure.
(a 25 second cool down must be allowed between each 0.5 second exposure.) This will avoid
the accumulation of excess heat and prolong the tube head life.
C. Tube head cooling curve
0
00.1 0.2 0.3 0.5 0.7 1235
5
10
15
20
25
30
00
1
12
210W
50kV
50kV
60kV
70kV
170W
130W
34
2
3
4
5
6
7
0
20
40
60
80
100
120
140
160
180
20 40 60 80 100
Time in Minutes
LoadTime (sec.)
Time in Minutes
Heat Storage (k H.U.)
Tube Current (mA)
Heat Storage (kJ)
HEAT UP
COOL DOWN
3. Maximum rating chart
1. Tube Hosung cooling curve 2. Anode thermal characteristics

-7-
SECTION 2 : PRE-INSTALLATION INSTRUCTION
[ 1 ] SUPPORT REQUIREMENTS
A. Arm and head
(1) Floor mounting type (FK1/FK2)
The floor and mounting hardware for floor mounting
plate must be sufficient to withstand a 100 kg withdrawal
force.
B. Main Controller (Fig.2-1)
(1) Floor mountint type (FK1/FK2)
The main controller is installed on the pole.
(2) Mobile type (FM)
The main controller is installed on the pole.
(3) Room type (RK)
The main controller is installed on the base plate.
C. Sub Controller (Fig.2-1)
The sub controller for FK1, FM and RK type is installed on the post.
FK2 type sub controller is installed on the wall.
When mounting the sub controller, the wall and mounting hardware must be sufficient to withstand
a 4.5kg shear load.
If the PHOT-X II Model 303 is to be mounted in a manner other than what is specified
in this manual or if the hardware to be used is other than what is supplied, the support
capability of the wall and the strength of the hardware must be checked and verified
to be adequate.
CAUTION
[ 2 ] ELECTRICAL REQUIREMENTS
A. Power supply
The model 303 x-ray system is operated on a power supply of rated line voltage ±10% with a three
wire (hot, neutral, earth) circuit, separately connected to the central distribution panel with an over
current protection device. Use a flexible cable approved by CEE (13) 52 or 53 consists of 0.75 mm2or
1 mm2conductors. Diameter of the sheath of cable should be 6 ~ 7.5 mm diameter. Line voltage
regulation should be within the range of 2 ~ 5% (for 100V, 110V type) or 0 ~ 3% (for 220V, 230V,
240V type) at rated current.
B. Concealed wiring for RK,FK2 (Fig.2-2)
Concealed wiring is accomplished by bringing conduit and wires in a flush mounted junction box
located behind the sub controller. Recommended height for the flush junction box is 1310 mm.
Wiring done in this manner should extend 300mm beyond the wall surface to allow sufficient wire for
connections. Interconnecting wires between main controller and sub controller should be 4 conductor,
0.5 mm2 , 300V. Maximum wire run distance is 10 m.
Note : All connections, workmanship and materials used must comply with the local codes.
Fig.2-2 Concealed Wiring
C
T1 T5
T2 T3 T4
FD
P
kV
60 70
mA
ab
4 7
INC
INC
CUS & PM
CUS
& PM
MLR OCC
MLR BW
OI
Main Controller
Sub Controller
Fig.2-1 Main Controller and
Sub Controller
Junction
Box
FROM
POWER
SOURCE
Terminal Block
in Main Controller
Terminal Block
in Sub Controller
WALL
1234
L N 4321
3P 4P 4P
Interconnecting Wire

-8-
SECTION 3 : INSTALLATION INSTRUCTIONS
[ 1 ] INSTALLATION REQUIREMENTS
Tools :
Standard tool kit including 1.5 mm, 2 mm, 3 mm and 5 mm allen keys.
Instruments :
Digital multimeter with an accuracy of 1%, capable of measuring 300 V AC and 10 mA DC,
and capable of indicating true RMS value within 1 sec.
Standard calculator.
TEST 1 : POWER SUPPLY
Prior to starting the installation inspect the power supply and confirm that the power supply is within
rated line voltage ±10 % and that the supply is a 3 wire earthed circuit, separately connected to the
central distribution panel with an overcurrent protection device.
This section explains the installation instructions for PHOT-XII MODEL 303.
After the installation is completed, PHOT-XII MODEL 303 requires the calibration
and inspection. Refer to SECTION 5.
CAUTION
[ 2 ] INSTALLATION OF FK1/FK2 TYPE
A. MOUNTING PLATE AND POLE INSTALLATION
1. Pass through the power supply cable in the centre
hole of floor mounting plate. (FK1 Type)
Pass through the power supply cable and inter-
connecting wires in the centre hole of floor mounting
plate. (FK2 Type)
Fix the floor mounting plate to the floor. Make sure
the mounting plate is firmly fixed and can withstand
a 100kg withdrawal force. (Fig.3-1)
2-1. FK1 Type
After setting the cover to the pole, pass through
the power supply cable in the lower hole (for
main controller) on the pole. Pass through the
interconnecting wire from the upper hole to the
lower hole on the pole. Connector side of wire
should come out from the lower hole.
(Fig.3-2)
2-2. FK2 Type
After setting the cover to the pole, pass through
the power supply cable and interconnecting
wire in the lower hole (for main controller) on
the pole. (Fig.3-2)
3. Attach the pole to the mounting plate by three
mounting bolts. Make the pole vertical by adjusting
three adjustment bolts and three mounting bolts.
Then set the cover to the pole. (Fig.3-2)
Fig.3-1 Fixing Floor Mounting Plate
ø350
P.C.D 300
Ø14-6Holes Mounting Plate
Power Supply
Cable (L=1500mm)
Interconnecting
Wires (L=1500mm)
(FK2 Type only)
Fig.3-2 Fixing Pole & Cover
Adjusting
Bolts
Mounting
Bolts
FK1 Type
Cover
Pole
Interconnecting
Wires (FK1)
Power supply
Cable
Adjusting
Bolts
Mounting
Bolts
FK2 Type
Cover
Pole
Interconnecting
Wires (FK2)
Power supply
Cable
Upper Hole Upper
Hole
Lower
Hole Lower
Hole
Mats
Mats
Mats
Mats

B. HORIZONTAL ARM INSTALLATION
1. Remove 2 set screws on the pole and remove
the pole bushing. (Fig.3-3)
2. Insert the horizontal arm into the pole bushing
then set stopper screw and brake plug, brake
spring and brake screw on the pole bushing.
(Fig.3-3)
3. After putting the back supporters to the pole,
insert the pole bushing and horizontal arm
into the pole with passing through the arm cable
into the lower hole on the pole then fix the pole
bush with 2 set screws.
(Fig.3-3)
Fig.3-4 Main Controller Fixing Plate Installation
Fig.3-3 Horizontal Arm Installation
Mats
Brake
Screw
Arm Cable
Stopper
Screw
Horizontal Arm
Pole Bushing
Set Screw
Lower Hole
Pole
Back
Supporter
(FK1)
Back
Supporter
Brake
Plug
Brake
Spring
Mats
Mats
Mats
C. MAIN CONTROLLER FIXING PLATE
INSTALLATION
1-1. FK1 Type
Pass through the interconnecting wire into the
FK1 back supporter on the upper hole and fix
the FK1 back support on the hole with 2 screws.
Pass through the arm cable, power supply cable
and interconnecting wire into the lower hole on
the main controller fixing plate.
Fix the main controller fixing plate to the back
supporters and pole with 8 screws. (Fig.3-4)
1-2. FK2 Type
Pass through the arm cable, power supply cable
and interconnecting wire into the lower hole on
the main controller fixing plate.
Fix the main controller fixing plate to the back
supporters and pole with 6 screws. (Fig.3-4)
FK1 Back
Supporter
Back
Supporter
Main Controller
Fixing Plate
Post
Back
Supporter
Back
Supporter
Main Controller
Fixing Plate
Post
FK1 Type FK2 Type
Interconnecting
Wires (FK1) Interconnecting
Wires (FK2)
Interconnecting
Wires (FK1)
Arm Cable Arm Cable
Power supply
Cable Power supply
Cable
Mats
Mats
-9-

-10-
Fig.3-5 Horizontal Arm Bottom Cover
Fig.3-6 Balance Arm Installation
D. BALANCE ARM INSTALLATION
1. During this procedure, do not remove Arm holding
band.
2. Remove two (M3 x 8mm) screws from the underside
of the horizontal arm to open the bottom cover.
(Fig.3-5)
3. Route the cable with 2P and 8P connectors from
the balance arm shaft through the horizontal arm.
Insert the balance arm into the horizontal arm.
The cable should be fed through the bottom cover
opening on the bottom of the horizontal arm.
(Fig.3-6)
Do not releaseArm holding band until the X-ray head has been installed.
Balance arm assembly is spring loaded and can cause equipment damage and injury
if not handled in the proper manner.
CAUTION !
DO NOT RELEASE
THIS BAND UNTIL
X-RAY HEAD IS
INSTALLED
Mats
Mats
Mats
Arm Holding
Band
Caution
Tag
Balance Arm
Shaft
Balance Arm
Cable from
Balance Arm
Mats
Mats
Mats
Horizontal Arm
Bottom
Cover
(M3 x 8)
Screw
CAUTION
4. Secure the 3 wires (Grounded wires) with ring
terminals together with the (M5 x 10mm) screw
on the bottom cover. (Fig.3-7A)
Note : Three ring terminals should not protrude from
a chassis plate. (Fig.3-7A)
5. Secure the wires from the balance arm to the bottom
cover with the nylon cable clamp to prevent damage
from twisting. (Fig.3-7B) Then connect the 2P and
8P connectors. (Fig.3-7C)
6. Re-attach the bottom cover to the horizontal arm
with two screws. (Fig.3-5)
Fig.3-7B Attaching Balance Arm Cable
on Bottom Cover
Fig.3-7A AttachingGrounded Wires on
Bottom Cover
Mats
Mats
Cable from
Balance Arm
Chassis Plate
(M5 x 10)
Screw
Mats
Mats
Nylon
Clamp
(M5 x 10)
Screw

-11-
7. Insert the brake plug and brake screw (M6 x 6mm)
into the horizontal arm collar. (Fig.3-8)
Do not fully tighten.
8. Remove the end cap from horizontal arm.
Insert the stopper screw into upper threaded hole
inside horizontal arm and tighten securely.
Replace the end cap. (Fig.3-8)
If stopper screw is not tightened securely, the
Balance Arm can lift out of the horizontal arm.
Fig.3-8 Attaching Balance Arm
to Horizontal Arm
CAUTION
E. HEAD INSTALLATION
Refer to page 16.
F. MAIN CONTROLLER INSTALLATION
Refer to page 17.
G. SUB CONTROLLER INSTALLATION
Refer to page 19.
H. ADJUSTMENT
1. Tighten the brake screw if arm drifts.
2. Perform the post installation inspection.
(page 21 ~ 23).
Mats
Mats
Brake Screw
Horizontal
Arm
Horizontal
Arm Collar
Stopper
Screw
Arm End Cap
Brake Plug
Balance Arm
Fig.3-7C Connection of Connectors
on Bottom Cover
Mats
Mats
2P Connector
8P Connector

-12-
[ 3 ] INSTALLATION OF FM TYPE
A. POLE ASSEMBLY INSTALLATION (Fig.3-9)
1. Attach four legs bars to the pole base and secure them
by hex socket head bolts. (Align the hole on bottom
of base with the threaded hole on the leg bar.).
Two longer leg bars must be attached to the
wider ends of the base.
2. Attach the lock casters to the each longer leg bar ends.
Attach the standard casters to the shorter leg bar ends.
CAUTION
Fig.3-9 Pole Assembly Installation
M8 X 20
Cap Bolts
Leg Bar
(Short)
Leg Bar
(Long)
Pole Bushing
Pole
Pole Base
Lock Caster
Lock Caster
Standard Caster
Standard
Caster
Mats
Mats
Mats
Mats
B. ARM ASSEMBLY INSTALLATION (Fig.3-10)
Do not release arm holding band until the X-ray
head has been installed. Balance arm is spring
loaded and can cause equipment damage and
injury if not handled in the proper manner.
1. Remove 2 mounting screws on the pole and remove
the pole bushing.
2. Insert the pole bushing into the shaft of balance arm.
3. Insert brake plug, brake spring and brake screw
(M6 x 6mm) into the upper threaded hole of pole
bushing. Do not fully tighten.
4. Insert the stopper screws into lower threaded hole of
pole bushing and tighten securely.
5. After putting 3 back supporters to the pole, insert the
pole bushing and balance arm into the pole as the
wires go through the lower hole of the pole.
WARNING
Fig.3-10 Arm Assembly Installation
Arm Holding
Band
Shaft of
Balance Arm
Pole Bushing
Stopper Screw
Mounting
Screws
Mats
Mats
Brake Plug
Brake Spring
Brake Screw
Arm Cable

D. HEAD INSTALLATION
Refer to page 16.
E. MAIN CONTROLLER INSTALLATION
Refer to page 17.
F. SUB CONTROLLER INSTALLATION
Refer to page 19.
G. ADJUSTMENT
1. Tighten the brake screw if arm drifts.
2. Perform the post installation inspection.
(page 21 ~ 23).
H. BALANCE ARM SWING ANGLE ADJUSTMENT
After installation of the head, balance arm swing angle
should be adjusted following 1 to 3.
1. Keeping the arm at the position (a) of Fig.3-12,
rotate the pole bushing to the limit by the direction
as the arrow in Fig.3-10 indicates.
2. Fix the pole bushing by two mounting screws on
the pole.
3. Confirm the swing angle of the arm is as Fig.3-12.
Fig.3-12 Balance Arm Swing Angle Adjustment
Long Leg
Short Leg
80˚
Position (a)
-13-
C. MAIN CONTROLLER FIXING PLATE
AND SUB CONTROLLER PLATE
INSTALLATION (Fig.3-11)
1. Pass through the interconnecting wire from the
upper hole to the lower hole on the pole.
Connecter side of wire should come out from the
lower hole.
2. Pass through the interconnecting wire and arm
cable into the large hole on the main controller
fixing plate. Set the main controller fixing plate
over the lower hole on the pole at the short leg side.
Fix the main controller fixing plate with 6 screws
to 2 back supporters and the pole.
3. Screw a cable hook on the main controller fixing
plate and fix it up right position with a nut from
opposite side.
4. Pass through the interconnecting wire into the
large hole on the sub controller fixing plate.
Set the sub controller fixing plate over the upper
hole of the pole at the short leg side.
Fix the sub controller fixing plate with 4 screws
to the back supporter and the pole.
Fig.3-11 Controller Fixing Plates Installation
Back
Supporter
Cable Hook
Nut
Main Controller
Fixing Plate
Sub Controller
Fixing Plate
Interconnecting
Wires
Interconnecting
Wires
Arm Cable

[ 4 ] INSTALLATION OF RK TYPE
A. BASE AND COLOMN INSTALLATION
1. Fix the base plate on the floor with 5 lag screws
(supplied) or with appropriate means.
(Fig.3-13)
Make sure the base plate is fixed on the floor
firmly.
2. Insert the sliding post with column cover into
the column. The direction of sliding post is
shown in Fig.3-14. (Fig.3-14)
3. Install the column on the baseplate with
mounting bolts. Make it vertical with adjusting
bolts. (Fig.3-15)
CAUTION
Fig.3-13 Fixing Base Plate to Floor
Fig.3-14 Setting Sliding Post
Fig.3-15 Fixing Column on Base Plate
-14-
Base Plate
Lag Screw
Mounting
Bolt
Adjusting
Bolt
Mats
Mats
Mats
Column
Base Plate
Mats
Mats
Mats
Sliding Post
Column Cover
Front
Side
Column
Front
Side
Fig.3-16 Swing Arm Installation
B. SWING ARM INSTALLATION
When installing the swing arm assembly on the
sliding post, keep holding the sliding post.
1. Pull down the sliding post into the column and
hold it. Set the thrust washer on the top of sliding
post. Keep holding the sliding post and insert the
swing arm assembly on the top of sliding post.
After setting the swing arm on the sliding post,
slowly release the sliding post. (Fig.3-16)
2. Set and fix the cable guide on the rear side of
column. (Fig.3-16)
CAUTION
Sliding Post
Column
Swing Arm 1
Swing Arm 2
Holding
Cable Guide
Cable Guide
Thrust Washer
Arm Cable
Set Screw
(M4 x 6)
Mats
Mats
Mats
Mats

2. Set the stopper screw into lower threaded hole of
swing arm 2. (Fig.3-17)
3. Set the brake plug then brake spring and brake screw
into the upper hole of swing arm 2. (Fig.3-17)
Tighten the brake screw, IF ARM DRIFTS.
DO NOT FULLY TIGHTEN.
4. Fix the cable guide on the rear side of colum with
2 screws. (Fig.3-16)
C. STOOL AND BACKREST CUSHION INSTALLATION
1. Slide up the backrest cushion to the top of column.
2. Insert the gas pump into the gas pump bracket.
Mount the stool seat on the gas pump then press
them. (Fig.3-18)
D. HEAD INSTALLATION
Refer to page 16.
E. MAIN CONTROLLER INSTALLATION
Refer to page 17.
After installation of the main controller, fix the
main controller on the base plate. (Fig.3-18)
F. SUB CONTROLLER INSTALLATION
Refer to page 19.
G. ADJUSTMENT
1. Tighten the brake screw if arm drifts.
2. Perform the post installation inspection.
(page 21 ~ 23)
Fig.3-17 Setting Brake Screw and Stopper
Screw on Swing Arm 2
-15-
Fig.3-18 Setting Stool
Gas Pump
Stool Seat
Base Plate
Mats
Mats
Stopper Screw
Swing Arm 2
Brake Plug
Brake
Spring
Brake Screw

-16-
WARNING
Fig.3-19 Setting Arm Collar on
Balance Arm
Fig.3-20 Removing Yoke Inside Cover
[ 5 ] HEAD ASSEMBLY INSTALLATION
Do not releaseArm holding band until the
X-ray head has been installed.
Balance arm assembly is spring loaded and
can cause equipment damage and injury
if not handled in the proper manner.
Refer to the Caution Tag on the band.
1. Remove the arm collar screw (M4 x 8mm) from
the arm collar. Slide the arm collar upward and
temporarily hold it in position with adhesive tape.
(Fig.3-19)
2. Open the yoke inside cover of x-ray head by
removing (M3 x8mm) countersunk screw.
(Fig.3-20)
Note : When opening the yoke inside cover,
use a short screw driver.
3. Making sure the stopper ring is placed on the
yoke, insert the wiring from the balance
arm assembly through the head shaft and into
the yoke. (Fig.3-21)
CAUTION !
DO NOT RELEASE
THIS BAND UNTIL
X-RAY HEAD IS
INSTALLED
CAUTION !
DO NOT RELEASE
THIS BAND UNTIL
X-RAY HEAD IS
INSTALLED
Arm Holding
Band
CautionTag
Adhesive
Tape
Arm Collar
Screw
(M4 x 8)
UP-Mark
Arm
Collar
UP
MatsMats
Mats
Yoke
X-ray Head
CPValues Label
Yoke Inside
Cover
Yoke Inside
Cover Screw
(M3 x 8)
Short Screw
Driver
4. Insert the shaft of the balance arm into the
head yoke, and while holding the head in
position, insert the head key securely into the
retaining groove. (Fig.3-21)
5. Remove adhesive tape and slide the arm collar
downward. Fix it in place with the arm collar
screw.
Remove the UP-mark from the arm collar.
(Fig.3-21)
Fig.3-21 X-ray Head Installation
CAUTION !
DO NOT RELEASE
THIS BAND UNTIL
X-RAY HEAD IS
INSTALLED
CAUTION !
DO NOT RELEASE
THIS BAND UNTIL
X-RAY HEAD IS
INSTALLED
Arm Holding
Band
CautionTag Arm Collar
Screw (M4 x 8)
Arm Collar
UP-Mark
Head Key
Stopper Ring
UP
Yoke
Head

Fig.3-22 Connection 10P Connector in Yoke
6. Loosen the (M5 x 10mm) screw and remove
the nylon cable clamp from the yoke housing.
Place cable clamp on the balance arm cable.
Connect the 10P connectors, and then attach
the balance arm cable to the yoke housing
with the nylon cable clamp. (Fig.3-22)
7. Remove the (M5 x 10mm) screw from the ground
terminal inside of the yoke housing.
Secure the green ground wires from balance arm
and head to the ground terminal with the
(M5 x 10mm) screw. (Fig.3-22)
8. Reattach the yoke inside cover with the screw
(M3 x8mm). Before closing the cover, note
the CP values on the CP values label inside
of the yoke. (Fig.3-20)
9. Remove arm holding band.
-17-
Fig.3-23A Fixing Main Controller (FK1/FK2, FM Type)
Ground
Terminal Nylon
Clamp
(M5 x10) Screw
10P
Connector
Yoke
Housing
[ 6 ] MAIN CONTROLLER INSTALLATION
1. Remove 4 cover screws and open the front cover. (Fig.3-23A, B)
2-1. FK1/FK2 Type
After passing through the arm cable, interconnecting wires and power supply cable into the hole on
the chassis of main controller, fix the main controller on the main controller fixing plate with
4 screws. (Fig.3-23A)
2-2. FM Type
After passing through the arm cable and interconnecting wires into the hole on the chassis of main
controller, fix the main controller on the main controller fixing plate with 4 screws.
Power supply cable is pre-fixed on the main controller. (Fig.3-23A)
Mats
Mats
Front Cover
Main Controller
Fixing Plate
Cable from
Arm Interconnecting
Wires Power Supply
Cable (FK1/FK2)

2-3. RK Type
Attach the mounting plate to the main controller with 2 screws.
Pass through the arm cable, interconnecting wires and power supply cable into the bottom hole on the
chassis of main controller.
Arm cable should be fixed by 2 clamps, one nylon clamp (insulated type) for holding the arm cable
and one plating clamp (conducting type) for shielding wire to be grounded. (Fig.3-23B)
3. Cut the wires of power supply cable to workable length and strip 10mm of insulation. Connect the
wires of power supply cable to 3P terminal block. (Fig.3-23B)
-18-
4-1. FK2, RK Type
Cut the interconnecting wires to workable length
and strip 10mm insulation. Connect the wires to
4P terminal block. (Fig.3-24)
4-2. FK1, FM Type
Connect 4P connector of interconnecting wires to
4P connector in the main controller.
(Fig.3-24)
Power Supply
Cable
3P Terminal
Block
4P Terminal Block
(FK2,RK Type)
4P Connecter
(FK1, FM Type)
Interconnecting
Wires
L
N
1
2
3
4
Fig.3-24 Power Supply Cable and
Interconnecting Wires Connection
Fig.3-23B Fixing Main Controller (RKType)
Mats
Mats
Front Cover
Arm Cable
Mounting
Plate
Main Controller
Chassis
Interconnecting
Wires
Power Supply
Cable (RK)
View A
Mats
Mats
Mats
Plating
Clamp Nylon Clamp
Arm Cable
Power Supply
Cable
Interconnecting
Wire
View A

-19-
Fig.3-25 Connecting 2P and 8P Connectors
on Power PC Board
[ 7 ] SUB CONTROLLER INSTALLATION
1. Remove two (M3 x8mm) screws from top of the
control box and open the front panel. (Fig.3-26)
2. Disconnect the 4P connector from the timer PC Board.
(Fig.3-27)
3. Route the interconnecting wires from the main
controller through access hole of chassis and
mount on the wall with three (ø4.1 x 20mm) wood
screws (FK2, RK type) or on the sub controller
plate with three (M4 x 10) screws. (FK1,FM type).
(Fig.3-27)
4. Cut 4 interconnecting wires from main controller
to a workable length. Strip 5mm insulation off the
wires and connect them to the 4P terminal block.
Terminal number for each wire should be matched to
the terminal number in the main controller.
(Fig.3-28)
Miswiring causes permanent damage to both
timer PC board and power PC board.
5. If wire length is too long, push it back into the access
hole of the wall. This will prevent mechanical damage
to the timer PC Board when replacing the front cover.
6. Reattach the 4P connector to the timer PC Board
(Fig.3-27)
Fig.3-27 Attaching Sub Controller
Chassis
CAUTION
Fig.3-26 Opening Front Panel
CFD
P
kV
6070
mA
ab
47
Screw (M3 x 8)
Front Panel
1234
Chassis
4P Connector
4PTerminal
Block
Interconnecting
wires
(From Main Controller
)
Front Panel
Timer PC
Board
Wood Screw
(ø4.1 x 20)
Chassis
4PTerminal
Block
4 InterconectingWires
(From Main Controller)
Sub Controller
Plate
(FK1,FMType)
1 2 3 4
Fig.3-28 Interconnecting Wires Connection
in Sub Controller
Ring
Terminals
2P
Connector
Power PC
Board
8P
Connector
(M5x10) Screw
Cable from Arm
5. Connect 8P connector of the arm cable to the
8P connector on power PC board.
Connect 2P connector of the arm cable to the
2P connector coming from PC board.
(Fig.3-25)
6. Connect 2 wires with ring terminals from the
arm cable to the chassis with a M5 screw.
(Fig.3-25)
Note : The front cover for the main controller
should not be closed until all installation
and the post-installation inspections and
confirmation are completed.
For RK type : Mounting plate should be attached to
the base plate with 2 screws after the
front cover for main controller is closed.