Belmont X-Calibur Series User manual

Operating
Instructions
IMPORTANT
Series
This manual provides operating instructions for the BEL-20N Chair.
The instructions contained in this booklet should be thoroughly read and understood
before operating the chair.
After the installation has been completed, keep this manual in a safe place and refer to
it for future maintenance.
BEL-20N CHAIR
R

CAUTION
1. OVERVIEW , MAJOR COMPONENTS AND SYMBOLS
1-1. Overview and major components
1-2. Symbols
17
18
1. Headrest Assembly
2. Backrest Cushion
3. Sling
4. Armrest
5. Side Frame
6. Rotation lock lever
7. Main Link Cover
8. Safety Plate
9. Base Cover
10. Seat Cushion
11. Pump Cover
12. Power Supply Cable
13. Backrest Cover
14. Rear Flange Cover
15. Seat height control
(Seat Raise/lower)
16. Backrest control
(Backrest Raise/recline)
17. Fuse holder
18. Main Power Switch
Applied part complying with the specified requirements of IEC60601-1:2005 to provide protection against
electrical shock, particularly regarding allowable patient leakage current and patient auxiliary current.
Caution, warning or note
The followings are prohibited.
To modify this equipment.
•
To use the equipment under any failure condition.•
To use the equipment without doing the daily and periodical check-up.•
To wipe the plastic covers with any disinfectant or detergent that contains organic solvent.•
To let a person on the chair who weighs over 300 lbs.•
To let two or more person on the chair.•
10
11
12
2
1
3
4
5
6
7
8
9
13
14
15
16
1

2. DIMENSIONS AND SPECIFICATIONS
2-1 Dimensions
(Inches)
Seat Initial Height ---------------------
Headrest bar Initial height ----------
Seat Lifting Stroke --------------------
Backrest Movement ------------------
Tilting Mechanism --------------------
Seat Rotation --------------------------
Armrest Rotation ---------------------
Auto Movements ---------------------
Electrical Requirement -------------
Fuse for power supply --------------
Fuse for relays ------------------------
Mode of Control ----------------------
Maximum Patient Load -------------
Weight ----------------------------------
2-2 Specifications
3-1 Main Powe r Switch
1) Plug chair into 120V AC outlet
3. OPERATIONS
2
13-3/4”
10-5/8”
15”
0 to 70° (above horizontal)
Backrest Synchronized Tilting (10 to 20°)
30° Left / 30° Right of the center line
Either armrest can be rotated outward
1 pre-set and auto return
AC120V/60Hz, 3.7A
10A/125V (Current rating : 750A at 250VAC) Fast-blow
1.25A/125V (Current rating : 750A at 250VAC) Fast-blow
Foot switch and backrest control
300 lbs (135 kg)
333 lbs (150 kg)
30°
30°
16
23-1/4
24
73-5/8
24-3/8 34-5/8 14-5/8 2-5/8 34-5/8 21-1/4
13-3/4 10-5/8
54-1/2
22-3/4
23-3/8
18-1/2
10-1/4
7-5/8
30-1/2
4-7/8
19-5/8 5-7/8
34-5/8 14-5/8
(Max 21-1/4)
23-1/4
Minimum 19”
to wall
Minimum 18”
to any object
73-5/8
Base (Rear)
21
Base (Front)

2)Turn on the main power switch located on the left side of the pump
cover. A green lamp will illuminate.
Operate the Main Power Switch by hand only. Turn off the main switch
after daily operation. Do not touch any switch with a wet hand, as it
might cause electric shock.
CAUTION
CAUTION
ON
OFF
Fig.3-1 Main Switch
NOTE
3-2 Controls
Before use
Check connection of switch and make sure that the device functions properly.
Make sure that grounding wire is connected.
Make sure that cables are properly and perfectly connected.
Be careful when you use the equipment combined with another, as it may lead to inadequate decision or
danger.
•
•
•
•
Patient Entry
Do not operate the chair until patient is fully seated. Patient head, back and feet must be in full contact
with seat cushions. Patient hands must be placed on top of forward facing armrests or on their lap.All
patients are at risk of potential injury if these precautions are not followed.
Do not allow patient to sit on the headrest, armrest, backrest or the end of seat. Do not give too much load
on the chair cushions. Failure to do so might lead to malfunction or an accident, such as fall from the
chair or break of the device
•
•
During use
Do not use the chair longer than required for examination or treatment.
Always watch the patient and the equipment to make sure nothing is wrong.
If anything wrong is observed with the equipment or the patient, take a proper action, such as stopping
the use of equipment as well as keeping the patient in safe.
Keep an eye on the patient not to touch the equipment.
Do not touch the patient and the fuse holder simultaneously.
•
•
•
•
•
After use
Turn off the switch and pull of the power supply plug.
Clean the equipment and get it ready for use.
•
•
Do not touch a switch on the foot control when Main Switch is turned on.
To avoid the risk of electric shock, this equipment must only be connected to a supply mains with protective
earth. Grounding reliability can only achieved when the equipment is connected to an equivalent receptacle
marked HOSPITAL ONLY or HOSPITAL GRADE.
CAUTION
3

Touchpad (Optional)
1) Seat Height Adjustments
a. Raise the seat by pressing foot, backrest or touchpad control (optional)
indicated “Seat Raise”.
b. Lower the seat by pressing foot,backrest or touchpad control (optional)
indicated “Seat Lower”.
2) Backrest Adjustments
a. Raise the seat by pressing foot, backrest or touchpad control indicated
“Backrest Raise”.
b. Lower the seat by pressing foot, backrest or touchpad control indicated
“Backrest Recline”.
3-3 Seat Rotation, Arm rest Rotation, Cancellation, Headrest adjustment
1)Armrest Rotation
Either armrest can be rotated outward by grasping lower back portion of armrest, pulling upward and turning.
CAUTION
AP
Seat Raise
Backrest
Recline
Backrest
Raise
Seat Lower
Pre-set
Auto
Return
Do not lean on an armrest nor sit on an armrest. It could damage an armrest or could cause an injury.
Seat Raise
Seat Lower
Backrest Raise
Backrest Recline
4
3) Auto Mode Control
a. Preset Control
BEL-20N chair has two preset positions. (Pre-set 1 and Pre-set 2)
Momentarily depress ( 1 ) button on the foot control, the chair will move
to the preset-1 position automatically. (Preset-2 is operated by ( 2 ) button.)
b. Auto Return
Momentarily depress ( 0 ) button on the foot control, the chair will return to
the initial position. (The seat is fully lowered and the backrest is in the
upright position.)
c. Last Position Memory
Momentarily depress (LP) button at the reclined backrest position
(treatment position), the backrest will raise to the mouth rinsing position automatically.
Momentarily depress (LP) button again, the backrest will recline to the previous
treatment position automatically.
Note : Seat height can not be changed by (LP) button.
4) AUTO MODE POSITION ADJUSTMENT
Two preset positions can be set.
Set the seat and the backrest to the desired preset position by manual
control switch.
Keep depressing pre-set 1 switch (1) until buzzer sounds (in about 3 seconds),
then release it. The position is memorized for Preset-1.
Preset-2 can be memorized by depressing pre-set 2 switch as same procedures.
5) Mouth Rinsing Position Adjustment
Mouth rinsing position in last position memory movement can be adjusted.
Set the backrest to the desired mouth rinsing position by manual control switch.
Keep depressing last position memory switch (LP) until buzzer sounds (in about 3 seconds) and release it.
This backrest position is then memorized as the mouth rinsing position.
Foot Control
Backrest
Raise
Auto
Return
Backrest
Recline
Seat Raise
Seat Lower
Pre-set 2
Pre-set 1
Last
Position

3-4 Positioning of Headrest
1. Seat patient upright and all of the way back on the chair.
2. Position the bottom of the headrest cushion so it is even
with the occipital of the patient’s head.
Viewing the lower arch
1. Using the latch release button (white), pivot the headrest cush-
ion halfway toward the patient’s head.
2. Have the patient lean back on the headrest.
3. Using the chair controls, place the patient in the desired operat-
ing position.
Viewing the upper arch
1. Lower the backrest and raise the base of the chair.
2. Slide the headrest in.
3. Support the patients head/headrest cushion while pressing latch release button.
4. Tilt the headrest cushion until the desired upper arch position is obtained.
Headrest Release
Lever
2) Chai r Rotation
To rotate the chair, release lock lever on right side of the chair, by pushing downward. Pull lever to lock.
3) Cancellation
a. Safety plate is provided below base link cover to stop motion of chair when object is accidentally caught
underneath.
b. Automatic motion activated either by automatic return switch or preset switch, can be cancelled at any time
by depressing any control switches.
4) Headrest Adjustment
a. Press down or pull up the headrest for height adjustment.
b. Grab the headrest release lever on headrest mechanism.
Take care not to pintch the fingers with the headrest mechanism.
CAUTION
5

Routine Care
Clean plastic and upholstery surfaces iegularly using a mild soap and water solution.
When cleaning, use a dampened cloth only, as excess cleaning solution can flow into the chair and cause perma-
nent damage to electrical components.
Barrier Technique
Use of disposable barrier products should be the first choice for the protection of dental equipment. Disinfectants
leave behind a surface residue that accumulates over time and eventually damages equipment and upholstery
surfaces.
Chemical Disinfection
If a chemical disinfectant is to be used on chair or upholstery surfaces, contact the manufacturer of the disinfec-
tant prior to use.
Obtain verification from the disinfectant manufacturer that their product will not damage the chair or upholstery
surfaces.
Unacceptable Disinfectants
The following chemicals may damage equipment and upholstery:
* Alcohol based solutions
* Bleach
* Phenol / Alcohol combinations
* Foam spray products
* Benzalconium chloride solutions
Use with Caution
* Water based phenolic disinfectants, following manufacturer’s exact instructions for use.
Warranty does not cover damage to equipment and upholstery caused by disinfectant solutions.
CAUTION
4. CARE AND MAINTENANCE
4-1 Cleaning and disinfection
NOTE
4-2-1 Storage
1. Keep the equipment away from water.
2. Keep in a circumstances safe from influence by temperature, humidity, wind, sun light, air containing salts and
minerals.
3. Care about stability such as inclination, vibration and impact, including handling and transportation.
4. Do not keep the equipment in a place where chemicals are or where gas is emitted.
4-2-2 Lifetime
Provided that the recommended and authorized care and maintenance are correctly performed, the working life-
time of this equipment is 10 years from the date of initial shipment from the manufacturer.
4-2 Storage and working lifetime
Do not spray liquids directly on to chair surfaces.
In order to prevent damage to electrical components and systems, do not apply excess cleaning solution on
to chair surfaces.
6

4-3 Daily Check-up of functions by the end user
The end-user is responsible for daily check-up of the equipment. In the case end user does not do this, it is
allowed that you outsource it to a technician authorized by us.
In order to assure safety use of this equipment, please carry out the following check-up in a frequency as
indicated below.
No. Item
(Frequency)
How to check and diagnose Influence of not doing
check-up
Actions when any incom-
pliance is found
1 Safety functions
(Daily. Before
opening office)
During pre-set movement or
auto-return movement, press any
key for chair operation and the
chair should automatically stop.
Injury caused by move-
ment of the chair during
treatment or pinching with
chair and other equipment
or furniture.
Call to a technician of our
authorized dealer.
2 Function of each
switch
(Daily. Before
opening office)
Each switch for chair operation
should work correctly.
Defect of movement may
cause an accident.
Call to a technician of our
authorized dealer.
3 Wiping off water
(Daily. Before
closing office)
Make sure that no water is left
that were spilt during treatment.
Water will cause rust Wipe off water with a soft
and dry cloth.
4 Stain removal of
external parts
(Dail y. Before
closing office)
Visually make sure that no dust,
chemical or other material is left
on the chair.
Such chemicals will cause
discoloration, dete-
rioration and break of the
plastics.
Thoroughly clean the
chair following the
cleaning instruction in
this book, regardless the
result of this check-up.
For tough stains, use mild
detergent solvency.
5 Main power
switch
(Daily. Before
closing office)
Make sure that the main power
switch is off
Accident or defect of the
equipment
In the case the main
power cannot be turned
off, Call to a technician of
our authorized dealer.
6 Moving parts
(Weekly)
Make sure that the chair does not
make any abnormal noise during
automatic movement
Accidend or defect of the
equipment
Call to a technician of our
authorized dealer.
7 Oil leakage
(Weekly)
Make sure that there is no hy-
draulic oil on the floor or chair
base leaking from the cylinder.
Defect of the equipment Call to a technician of our
authorized dealer.
8 Power supply
cable
(Monthly)
Power supply cable should not
be abnormally bent, pintched or
damaged, and the plug should
befirmly inserted to the power
outlet and not covered with dust.
Accident or defect of the
equipment
Clean and rearrange the
cable. For replacement,
call to a technician of our
authorized dealer.
7

4-4 Guideline for Periodical Check-up
Some parts and components of the products are degraded or deteriorated depending on the frequency of use,
so yearly check-up and maintenance, as well as replacement of comsumable parts, are required.
For check-up and repair, call a technician of our authorized dealer.
•
•
Parts and components that require periodical check-up
Parts Description
Moving part
Standard LifetimeNo.
7 years1
2 Electric wiring of moving parts 5 years
3 Switches 5 years
5 years
3 Base Cover
Pump Cover
4
Control PCBs4
Consumables
No.Parts Description
1 Power supply cord
2 Cusions and Upholsteries
4-6 Disposal
This is not an infecious device, but prior to disposal make sure that no parts of the device is infected.•
Follow the federal, state and local regulations for disposal.•
4-5 Replacement of consumables
Replacement must be done by an professional technician(s) of our company or a company authorized by us.
1. Power supply cord
2. Cushions and upholsteries
See the installation manual enclosed with this manual. The procedure is described in 4-2 Installation.
BrownBrown
Blue
Green/Yellow
Light Blue
Green/Yellow
Power CordTo Switch Section
Terminal BTB15LC3
Pump Cover
Power Cord
Pump cover screw plate
M5 Set Screw
M5 Set Screw
1) Remove 3 M5 set screws and remove the pump cover.
2) Remove the screws for power cable on the terminal block.
3) Remove the cord bush from the pump cover screw plate.
4) Take the opposite procedure to install a new power cord.
Cord Bush
8