Belnick ZG-035-GY-GG User manual

Thankyouforyourpurchase!
Customer Service Email: [email protected] | Phone: [phone]
ZG-035-GY-GG / ZG-035-OAK-GG
75 L B S
50 LBS
25 LB S
ASSEMBLY INSTRUCTIONS
Before You Begin:
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching
during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may
result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where
included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The
tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall
Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.
End Table

Have a Question/Concern?
Quality products and first-class customer service are the cornerstone of long-lasting
consumer relationships. We strive toward excellence in all we do and want you to be
completely satisfied with your purchase.
Please contact our exceptional Customer Experience Agents at the email address
or phone number shown below to assist you with any product questions or
issues before requesting a return.
We look forward to serving you in a friendly, efficient manner to resolve any issues you
may have.
Customer Service Email: [e-mail]
Customer Service Phone: [phone]
Our Warranty Statement
This warranty covers manufacturing defects associated with your new product. The product is
warranted from the original purchase date and to the original purchaser for normal usage,
according to the below-referenced specifications and limitations.
Non-moving metal parts are warranted for 5 years.
Component parts including pneumatic cylinder, control mechanism, base and casters are
warranted for 2 years.
All other items are warranted for 1 year.
Normal usage means use in compliance with the restrictions and weight limits specified for the
product. In the absence of product-specific restrictions and weight limits, normal usage means use
for no more than forty hours per week by persons weighing 250 lbs. or less. Coverage terminates if
the product is sold or otherwise transferred. Repairs made by parties other than Belnick also void
this warranty.
This warranty will not cover: (1) labor, freight, or damage from misuse, abuse, negligence,
alteration, assembly, installation, attachments, accident, vandalism, acts of nature or any other
event beyond the control of Belnick; (2) tearing, scratching, scuffing, or blemishing of leather or
fabric; (3) cosmetic damage that may result from normal usage; (4) damage attributable to use by
persons exceeding specified weight limits or commercial use exceeding forty hours per week; or (5)
rust or other damage caused by exposure to moisture. The user assumes all risk of injury resulting
from use of this product. Liability for incidental or consequential damage is excluded. Some states
do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
• Check you have all the
components and tools listed on
the following pages.
plastic bags and separate them
into their groups.
• Keep children and animals
away from the work area, small
parts could choke if swallowed.
• Make sure you have enough
space to layout the parts before
starting.
Care and maintenance
• Only clean using a damp cloth
and mild detergent, do no use
bleach or abrasive cleaners.
• From time to time check that
there are no loose screws on
this unit.
• This product should not be
discarded with household waste.
Take to your local authority
waste disposal centre.
Handy Hints
• Assemble all parts and bolts
loosely during assembly, only
once the product is complete
should you fully tighten the bolts
• Regularly check and ensure
tightend properly.
• During assembly do not stand
or put weight on the product,
this could cause damage.
• Assemble the item as close
room) as possible.
• Assemble on a soft level
surface to avoid damaging the
• Parts of the assembly will be
easier with 2 people.
• To reduce
the likelihood of
damaging your
product please
ensure that your
power drill is set on a low torque
setting.
WARNING
In order to help prevent overturning –
To help prevent product toppling over please follow the below steps:-
Do not open more than one drawer at a time
Do not place heavy items in the top drawers
Do not place heavy items on top of the furniture, unless the furniture has been
designed for this purpose
You will need to provide wall plugs and screws applicable for your wall type
1
!
• Remove all fittings from the
to its final position (in the same
unit or your floor.
That all bolts and fittings are
please follow these instructions
Do not allow children to climb or hang on the furniture
Use the anti tip stap or wall fixing method provided (if applicable)
Please note that only the anti tip strap is provided.

Components -Fittings
Please check you have all the panels listed below
Note: 

   e '
  
 / 
 
   
  
0 
 
Tools required
 
 
  
2
B  N    

Using Camlocks
12
DO NOT OVER TIGHTEN.
NE PAS SERRER EXCESSIVEMENT.
34
4
Step 1
Step 3
Step 2
Step 4
Connect the male
camlock as diected in
the assembly instructions
using a scewdriver.
Push the male camlock
into the entry hole.
Insert the female
camlock as shown in the
instruction.
Note：ensure that the
arrow on the top of the
camlock points towards
the entry hole for the
male camlock.
Turn the female camlock
clockwise with a
screwdriver.
You should feel a click
when the camlock is
locked in place.
The joint is now secure.

Assembly Instructions
 •

Top Panel
Rear Leg 

Q 0

I

�e

0�
Q

Front Leg
� 0
 �\S

 Bottom Panel
Rear Leg .
tr0
 '

Front Leg
4

Assembly Instructions
Step 1
Step 2
A
X2
A
C
C
C
C

Assembly Instructions
Step 3
Step 4
B
B
E
E
D
D
F
1 2 3

Assembly Instructions
Step 5
Step 6
E
E
D
D
B
B
F
1 2 3
A
A
A
A

Assembly Instructions
Step 7
Step 8
B
B
B
B
1 2 3
1
2
1
23
4
5
3
J
J
J
J

Assembly Instructions
Step 9
Step 10
X8 I
G
HH
HH
6
7
X2

Assembly Instructions
Step 11
Step 12
3
4
5
6
7
2
11
2
H
H
7
6
X2
1.
1
6
2.
3.
2
7
H
H
5
7
6
K
K

Assembly Instructions
Step 13
Assembly is complete.
3
4
5
6
7
2
11
2
H
H
1.
1
6
2.
3.
2
7
H
H
5
7
6
K
K