Belnick ES-G1-24-WH-GG User manual

Customer Service Email: [e-mail] | Phone: [phone]
ES-G1-24-WH-GG / ES-G1-29-WH-GG / ES-G1-24-GY-GG / ES-G1-29-GY-GG
ASSEMBLY INSTRUCTIONS
Before You Begin: Phillips Screwdriver is required (Not Included).
Please identify all component parts and hardware pieces required before you begin. Carefully remove all of the
components from the packaging and set aside for assembly. Assemble on a soft surface to prevent scratching
during assembly.
Caution:
Tighten all components securely before use. Failure to do so may result in personal injury.
DO NOT use any sharp objects to open plastic wrapped components as damage to product or components may
result.
Warning:
CHOKING HAZARD - Small Parts. Adult Assembly Required.
DO NOT ALLOW CHILDREN TO CLIMB ON FURNITURE
Serious or fatal injuries can occur from furniture tipping over. You must install Tipping Restraint Hardware (where
included) to help prevent the unit from tipping and causing accidental injury, instability, death or damage. The
tipping restraint is intended only as a safety measure, it is not a substitute for proper adult supervision.
To help prevent furniture from tipping over it must be permanently attached to the wall. Anti-Tip Safety Wall
Straps suitable for the unit weight and wall materials (if not included) should be purchased and installed.
Commercial Grade Wooden
Modern Farmhouse Swivel
Bar Height Stool
300
Thank you for your purchase!

Have a Question/Concern?
Quality products and first-class customer service are the cornerstone of long-lasting
consumer relationships. We strive toward excellence in all we do and want you to be
completely satisfied with your purchase.
Please contact our exceptional Customer Experience Agents at the email address
or phone number shown below to assist you with any product questions or
issues before requesting a return.
We look forward to serving you in a friendly, efficient manner to resolve any issues you
may have.
Customer Service Email: [e-mail]
Customer Service Phone: [phone]
Our Warranty Statement
This warranty covers manufacturing defects associated with your new product. The product is
warranted from the original purchase date and to the original purchaser for normal usage,
according to the below-referenced specifications and limitations.
•Non-moving metal parts are warranted for 5 years.
•Component parts including pneumatic cylinder, control mechanism, base and casters are
warranted for 2 years.
•All other items are warranted for 1 year.
Normal usage means use in compliance with the restrictions and weight limits specified for the
product. In the absence of product-specific restrictions and weight limits, normal usage means use
for no more than forty hours per week by persons weighing 250 lbs. or less. Coverage terminates if
the product is sold or otherwise transferred. Repairs made by parties other than Belnick also void
this warranty.
This warranty will not cover: (1) labor, freight, or damage from misuse, abuse, negligence,
alteration, assembly, installation, attachments, accident, vandalism, acts of nature or any other
event beyond the control of Belnick; (2) tearing, scratching, scuffing, or blemishing of leather or
fabric; (3) cosmetic damage that may result from normal usage; (4) damage attributable to use by
persons exceeding specified weight limits or commercial use exceeding forty hours per week; or (5)
rust or other damage caused by exposure to moisture. The user assumes all risk of injury resulting
from use of this product. Liability for incidental or consequential damage is excluded. Some states
do not allow the exclusion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you.

ASSEMBLY INSTRUCTION
IMPORTANT NOTE:



P  S  q  (  I  )
 
0    
     
   
  
    
® �
(  

  
 q
  •1■! 
    
5    
L Small J 
       
 
 
4
L Big J
0
7   
 
   
NOTE : Do not tighten all the screws until the stool is fully assembled.
STEP 1



 
 


0

d  f 
 M6x  mm 
 x  k  d 

STEP 2 
 
0

 M6x  mm  x 
 k  d 

Allen
Wrench
Flat Washer
Lock Washer
M6x45mm
Hex Screw
Chair Leg w/Hole
Apron with Swivel
Plate
Chair Leg (No Hole)

ASSEMBLY INSTRUCTION
NOTE : 
STEP 3

 
Small Small
Attach Front & Back Footrests (Part C) to the small holes on the
Chair Legs (F & G) using (4) M 4 x 3 8 mm Phillips Screws (Part 1).
Tighten loosely with Phillips Screwdriver ( N ot Included).


Attach the Backrest (Part A) to the Seat (Part B) using (4)
M 6 x 45mm H e x Screws (Part 3), (4) Lock Washers (Part 4)
and (4) small Flat Washers (Part 6). Tighten loosely with
Allen Wrench (Part 7).
STEP4


D --�
I---�
Big Big
Attach Left & Right Footrests (Part D) to the large holes on the
Chair Legs (F & G) using (4)
M 4 x 3 8 mm Phillips Screws (Part 1).
Tighten loosely with Phillips Screwdriver ( N ot Included).
STEP 6



Invert the assembled backrest and seat on a stable raised
surface such as a table. Attach the Swivel Plate located on the
Apron with Swivel Plate (Part E) to the Seat using (4) M 6 x 2 0 mm
H e x Screws (Part 2) and (4) Flat Washers (Part 5) Tighten all
screws using the Allen Wrench (Part 7). Return Chair to the
upright position.
ENSURE THAT ALL SCREWS ARE FULLY TIGHTENED BEFORE USE.
Front & Back Footrests
Left & Right Footrests
M4x38mm Phillips Screw M4x38mm Phillips Screw
Seat
Backrest
Allen Wrench
M6x20mm Screw
Flat Washer
M6x45mm
Hex Screw
Allen
Wrench
Lock Washer
Small Flat
Washer