Beninca CALL User manual

L8542447
06/2009 rev 3 ENG
CALL
UNIONE NAZIONALE COSTRUTTORI
AUTOMATISMI PER CANCELLI, PORTE
SERRANDE ED AFFINI

F2
F2
F2 115V 0,2AT
F2 230V 0,1AT
F2 24V 0,5AT
N
C H 1
P G
CH2 CH3 CH4
L
ANT
SHIELD
ANT
BATT 12Vdc
+
-
U2
RADIO
J4
CH4 N.O.
CH4 N.C.
J3
CH3 N.O.
CH3 N.C.
J2
CH2 N.O.
CH2 N.C.
J1
CH1 N.O.
CH1 N.C.
ADV
N.C.
12
3456789
1 0
1 1
1 2
1 3
1 4
F1
T315mA
LED1
LED2
LED3
LED4
LED5
LED6
PB1
ALARM
12345
SIM CARD
3

CALL
GSM four channel receiver
Quick start
The basic steps to install and program a new SIM in the CALL system are described hereunder.
For further information on the various functions, refer to the other sections of this manual.
1) Insert the SIM* in a mobile phone, remove the PIN code and the telephone answering function, if activa-
ted.
2) Remove the SIM from the mobile phone and insert it in the CALL.
3) RESET the SIM, as indicated in the “SIM RESET” section.
4) Change the access password as indicated in the “Access PASSWORD” section, thus selecting the
system operating mode (Safety Access or Open Access).
5) If the selected mode is Safety Access, store the telephone numbers to be enabled and the related custo-
mizations into memory.
6) If the selected mode is Open Access, the system is ready for use.
* Check that the SIM that is to be used for the CALL system is activated, take note of the telephone number
of the SIM itself.
The vocal calls and the SMS controls can be sent also from xed telephones.
WARNINGS
The customized password (modpsw) and, in general, when commands are typed in, it is important not to
leave any spaces unintentionally.
The system, in fact, considers spaces as actual digits so that password “1234567 ” differs from “1234567”
as the rst password features a blank at end of string.
For the same reason, when entering the various phone numbers for enable, disable purposes, etc., it is
important not to leave blank spaces between the various numbers, for ex.:
addnum 123456 3391234567,3391234568,33912345679
is correct at the phone numbers are separated by a comma only.
while
addnum 123456 3391234567, 3391234568, 33912345679
is incorrect and only the rst number will be stored in memory
3

CALL
CALL is composed of a four-channel receiver, controlled by a GSM module, which can be activated by
mobile phones, in addition to radio transmitters, through which it is possible to:
- Activate a receiver channel through normal vocal call (this call is free of charge as the device cuts off the
call after a few rings, without answering);
- Activate either of the 4 channels by sending a text message (SMS).
The GSM module can be programmed in two different ways:
The “Safety Access” mode (default setting) allows for the programming of all available functions. The most
important are:
- Enabling/disabling of the telephone numbers in the SIM memory of the Call (up to 200 telephone num-
bers can be stored in memory);
- Setting the modication of each memorised number;
- Activation/deactivation of the radio receivers (rolling code);
- Change of the safety password;
- Asking the device to know:
1) the status of outputs
2) how many and which numbers of mobile phone are stored in memory and with which presettings
3) the number of activated transmitters
4) whether a specic transmitter it enabled
5) the number of SMS messages that were sent to the GSM module of Call
- Release/lock of the receiver radio menu in order to prevent the storage in memory of new transmitter
codes through the receiver functions. Memorisation is now enabled only through mobile phones.
The “Open Access” mode does not provide for the storage in memory of the telephone numbers in the
CALL memory. Any telephone may therefore activate the channels through a call or an activation SMS mes-
sage, thus exceeding the preset 200 number limit of the standard mode.
HOW TO CONNECT, SWITCH ON AND INITIALIZE THE SYSTEM:
Introduce a SIM card in the special seat in the device. There are no limits to the network operator. However,
the SIM that is intended for this use must be without PIN code. The SIM card must be in a mobile phone for
which, when switched on, the PIN request function is disabled.
The device can be connected to the 230V power mains (the device can be also connected to a 12V buffer
battery).
After an initialization cycle, the device switches to the regular operation mode (see section “LED diagno-
stics”).
SIM RESET:
A RESET must be performed if a SIM has never been previously used in a CALL receiver.
This operation involves the following: erase message memory, erase address book, reset SMS counters,
new presetting of default password.
To reset the SIM card proceed as follows:
- Cut off power supply
- Press the module key (PB1)
- Power the device keeping the key pressed
- The module switches on
- After approximately 10 seconds, the red LED switches on with xed light (the key can be released)
- The red LED stays on for 2 about minutes. When it switches off, the operation is completed and the
message and address-book memory have been erased. The SMS counters have been reset and the
default password, which is 123456, has been restored.
- At this point, the module enters the normal operating mode.
5

LED DIAGNOSTICS
The 6 LED of the GSM module allow for the monitoring of the status of the CALL system:
LED 1 (red):
1 ash every 2 seconds: SIM correctly recorded in the GSM network
2 ashes every second: SIM in the recording mode in the GSM network
LED 2 (yellow):
It ashes rapidly in the transmission phase
LED 3 (yellow):
It ashes rapidly in the receiving phase
LED 4 (green):
Continuous ashing: SIM in the initialization phase
From 1 to 5 ashes, followed by an interval: GSM reception level (1: minimum level – 5: maximum level)
LED 5 (red):
It switches on when an entering command is being processed.
If the credit of the SIM is nished, LED 5 will switch on with xed light.
LED 6 (green):
Switched on with xed light: correct operation of the software
Flashing: error in the software
During normal operation the LED status is as follows:
LED 1: ashing every 2 seconds
LED 2 and LED 3: continuous ashing
LED 4: from 1 to 5 ashes to show reception level
LED 5: switched off (it switches on if an SMS is received)
LED 6: switched on with xed light
ACCESS PASSWORD
All programming controls provide for an access password.
For safety reasons, the rst operation to be carried out is to change password.
Send an SMS message with this text:
modpsw 123456 112233
where:
modpsw command string
123456 default password (or password currently in use which you wish to change)
112233 new password (max 10 numeric characters). When a new password is set,
the old one will no longer be valid.
REPLY:
“PASSWORD UPDATED ”
The default password can be restored by resetting the SIM.
The type of password typed in also selects the operating mode (Safety Access or Open
Access).
If the rst gure of the password is different from “0” (zero), the system sets in Safety
Access mode.
If the rst gure of the password is “0” (zero), the system sets in Open Access mode.
5

“SAFETY ACCESS” OPERATING MODE
This mode allows to activate the channels only by telephone numbers memorised through one of the pro-
cedures described in the “PROGRAMMING” section. It is then possible to:
- ACTIVATE A CHANNELTHROUGH VOCAL CALL: call the CALL device with a telephone the number of
which had been previously memorised. After 2 rings, the call is cut off automatically and channel 1 is ac-
tivated (the channel to be activated by this type of call can be changed through command “modnum”).
- ACTIVATE A CHANNEL THROUGH SMS: through a mobile phone, the number of which had been
previously memorised. Send an SMS to the CALL device with the text message “ch1”. As soon as the
device receives the text message, channel 1 will be activated (or send ch2, ch3, ch4 according to the
channel to be activated). As described hereunder, the text of the message intended to activate the
channels, can be modied.
Note: if you wish to receive an acknowledgement text message by the CALL device, the message must be
“?ch1”. The reply will be “COMANDO ESEGUITO CORRETTAMENTE” (“COMMAND OK”)
“OPEN ACCESS” OPERATING MODE
This mode allows to activate the channels from any telephone with no need to store the related number in
the CALL memory:
- ACTIVATION OF A CHANNEL THROUGH VOCAL CALL: call the CALL device from any telephone. After
2 rings the call will be cut off automatically and channel 1will be activated.
- ACTIVATION THROUGH SMS: from any telephone, send an SMS to the CALL device with the text mes-
sage “ch1”. As soon as the device receives the text message, channel 1 will be activated (or send ch2,
ch3, ch4 according to the channel to be activated). As described hereunder, the text of the message
intended to activate the channels, can be modied.
Note: if you wish to receive an acknowledgement text message by the CALL device, the message must be
“?ch1”. The reply will be “COMANDO ESEGUITO CORRETTAMENTE” (“COMMAND OK”)
PROGRAMMING
Programming is performed by sending the control signals through a SMS from a mobile phone to the num-
ber of SIM present in the CALL device.
The various programming control signals are described hereunder.
ADD USER TO THE LIST OF ENABLED TELEPHONE NUMBERS:
Mobile telephone numbers (or xed telephone numbers) can be added to the memory of the device in two
ways:
1) Type in a SMS command:
addnum 12345 3391234567,n°2,n°3,n°4…
where:
addnum command string
123456 access password
3391234567 telephone number to be added to the list
n°2,n°3,n°4 if more than one number is to be added in one single message, it is
sufcient to separate them with “,”
N.B.:
N.B.:
- Omit any 0 (zero) at the beginning of the number sequence to be memorised.
For example, if the number to be entered is 03391234567, type the number 3391234567 in the com-
mand.
- When a number is memorised via SMS, it acquires the default permissions and settings. Therefore, the
vocal call will activate channel 1, while with the text messages it is possible to activate all 4 channels.
These settings can be modied with the “modnum” command.
- To allow for a correct operation of the vocal call, the telephone calling shall not have the “hide number”
function activated.
- If an acknowledgement reply of the vocal call is to be received from the device, the control signal shall
be:
?addnum 123456 3391234567;n°2;n°3;n°4
The reply will be: “USER ADDED”
6
7

2) Manual typing in:
- remove the SIM from the CALL device and insert it in a mobile phone
- store the telephone numbers to be enabled in the SIM address book proceeding as follows:
in the user name eld type the telephone number to be memorised
in the telephone number eld, digit 0 or, if settings of channels are to be customized, the presetting 5-
digit string described in section “How to modify the permitted access of one or more numbers”.
HOW TO MODIFY THE PERMITTED ACCESS OF ONE OR MORE NUMBERS:
This command permits to modify the permitted access and presetting of one or more mobile phone num-
bers, or it permits or denies the possibility to activate some channels, change the combination call/channel
to be activated, call in the event of alarm.
modnum 123456 00000 3391234567,n°2,n°3,n°4...
where:
modnum command string
123456 access password
00000 string regarding channel presetting and permitted accesses to channels *
3391234567 enter the number the permitted access of which should be modied
n°2,n°3,n°4 more than one number can be modied by dividing them with “,”
* the string regarding channel presetting and permitted accesses to channels is composed of 5 digits:
Digit 1: activation with phone call:
“0” = denied access (the phone call activates no channel)
“1” = the phone call activates channel 1
“2” = the phone call activates channel 2
“3” = the phone call activates channel 3
“4” = the phone call activates channel 4
Digit 2: activation of channel 1 by SMS:
“0” = denied access (channel 1 cannot be activated through SMS)
“1” = channel 1 can be activated (through the sending of SMS1)
Digit 3: activation of channel 2 by SMS:
“0” = the phone call activates channel (channel 2 cannot be activated through SMS)
“1” = channel 2 can be activated ( (through the sending of SMS2)
Digit 4: activation of channel 3 by SMS:
“0” = denied access (channel 3 cannot be activated through SMS)
“1” = channel 3 can be activated (through the sending of SMS3)
Digit 5: activation of channel 4 by SMS:
“0” = denied access (channel 4 cannot be activated through SMS)
“1” = channel 4 can be activated (through the sending of SMS4)
If a number, which was not previously memorised, is entered in among the numbers typed in the odnum
command, this number will be added to the list with presetting and permitted access indicated in the com-
mand.
If a reply should be sent by the device, the command shall be:
?modnum 123456 000000 3391234567,n°2,n°3,n°4
The reply will be : “CONFIGURATION UPDATE OK”
REMOVE USER FROM LIST OF ENABLED PHONES:
This command permits to remove one or more numbers from memory.
delnum 123456 3391234567
where:
delnum command string
123456 access password
3391234567 telephone number to be removed from list
If a reply should be sent by the device, the command shall be:
?delnum 123456 3391234567
The reply will be: “USER DELETED”
6
7

REQUEST OF GENERAL STATUS OF THE MODULE:
This command signal permits to receive some information on the device:
the number of messages sent, the number of transmitter codes preset in memory, the software and
rmware version of the GSM module, the network operator to which the device is connected, the number
of mobile phones stored in memory.
status 123456
where:
status command string
123456 access password (this is the default password if it has not modied yet or if
the module has been just initialized)
REPLY:
Sms sent: 0; Tx rec: 0; Sw:1.0.0; Fw:1.0.0.; Op:vodafone; phs:n/200
where:
Sms sent: 0 number of SMS sent from the last time counters have been reset
Tx rec: 0 number of transmitters stored in the receiver
Sw:1.0.0 software version of the GSM board
Fw:1.0.0. rmware of the GSM module
Op:vodafone network operator
phs:n/200 phonebook status: number of phone numbers stored in memory / maximum
phone numbers storable in memory
STATUS REQUEST OF PRESETTING AND PERMITTED ACCESSES OF A NUMBER:
This command allows to know presetting (presetting of alarm and channel to be activated by phone call)
and permitted accesses (channels which can be activated by SMS) regarding one specic number stored
in memory.
numstatus 123456 3391234567
where:
numstatus command string
123456 access password
3391234567 telephone number to be added to the list
REPLY:
ALARM:ON/OFF,CALL:1/2/3/4,ch1:ON/OFF,ch2:ON/OFF,ch3:ON/OFF,ch4:ON/OFF
where:
ALLARM:ON/OFF notice of activated/deactivated alarm
CALL:1/2/3/4 number showing the channel which can be activated by phone call
ch1:ON/OFF activation status of channel 1 by SMS
ch2:ON/OFF activation status of channel 2 by SMS
ch3:ON/OFF activation status of channel 3 by SMS
ch4:ON/OFF activation status of channel 4 by SMS
READ LIST OF ENABLED PHONES:
This command permits to know the number of memorised phone numbers.
readbook 123456
where:
readbook command string
123456 access password
REPLY:
n°1;n°2;n°3;
8
9

RESET OF SENT SMS COUNTER:
This command permits to reset the counter of SMS sent by the CALL device. This counter can be useful to
count the messages sent since the last recharge made in order to estimate the remaining credit.
smsreset 123456
where:
smsreset command string
123456 access password
If a reply should be sent by the device, the command shall be:
?smsreset 123456
The reply will be: “COMMAND OK”
OUTPUT COMMAND MESSAGE:
This command permits to modify the text of channel activation SMS, so as to be able to combine a specic
output to an ID word of the device to be activated or deactivated.
(example: if the gate is connected to channel 1, the SMS linked to channel 1 can be modied with the word-
ing “GATE”)
setcmdmsg 123456 1 GATE
where:
setcmdmsg command string
123456 access password
1 SMS to be modied (1-4)
GATE channel activation string (20 digits max)
N.B.: the text of the 4 SMS is the default text: Ch1, Ch2, Ch3 and Ch4 (words corresponding to SMS1,
SMS2, SMS3, SMS4, respectively)
If a reply should be sent by the device, the command shall be:
?setcmdmsg 123456 1 GATE
The reply will be: “COMMAND MESSAGE SET”
ADD TRANSMITTER CODE IN THE RECEIVER CONNECTED TO MODULE:
This command permits to add a transmitter code to the receiver memory without necessarily gain access to
the control unit (the serial number of the transmitter to be entered must be known). Through this command
only 2-channel transmitters can be entered. To enter 4-channel transmitters proceed through the radio
Menu of the receiver (see instructions of RR.4).
addtx 123456 02D762D
where:
addtx command string
123456 access password
02D762D string of 7 hexadecimal digits (0 – F) representing the SN of the TX to be
added to the receiver memory
N.B.: the following is added by default to the TX added : key1>channel, key 2>channel 2.
The serial number of remote controls is indicated outside the remote controls in series, or it can be read
through the ADVANTAGE system.
If a reply should be sent by the device, the command shall be:
?addtx 123456 02D762D
The reply will be: “COMMAND OK”
8
9

HOW TO DISABLE THE TX PRESENT IN THE RECEIVER CONNECTED TO THE MODULO:
This command permits to disable a transmitter. This will remain stored in the receiver memory but it will not
activate any channel (to restore it, use command “addtx”)
distx 123456 02D762D
where:
distx command string
123456 access password
02D762D string of 7 hexadecimal digits (0 – F) representing the SN of the TX to be
disabled from the receiver memory
N.B.: To reset a disabled transmitter, enter it again with command “addtx”
If a reply should be sent by the device, the command shall be:
?distx 123456 02D762D
The reply will be: “COMMAND OK”
REQUEST OF TRANSMITTER STATUS IN RECEIVER CONNECTED TO THE MODULE:
This command permits to know whether a specic transmitter is enabled or not
testtx 123456 02D762D
where:
testtx command string
123456 access password
02D762D string of 7 hexadecimal digits (0 – F) representing the SN of the TX to
request the status
The reply will be one of the following
“TRANSMITTER ENABLED”
“TRANSMITTER DISABLED”
“TRANSMITTER NOT PRESENT”
ACTIVATION OF THE TRANSMITTER ENTER BLOCKTHROUGH RECEIVER:
This command permits to block the access to the radio menu functions of the receiver making it possible to
enter the new transmitters only through mobile phone (command “addtx”).
setrxpsw 123456
where:
setrxpsw command string
123456 access password
REPLY:
“COMMAND OK”
DEACTIVATION OF TRANSMITTER ENTER BLOC THROUGH RECEIVER:
This command permits to reactivate the access to the radio menu functions of the receiver making it possi-
ble to store in memory new transmitters through both the use of a mobile phone and the normal functions
of the receiver.
resetrxpsw 123456
where:
resetrxpsw command string
123456 access password
RISPOSTA:
“COMMAND OK”
10
11

STATUS REQUEST OF RECEIVER OUTPUTS:
This command permits to know the status of outputs, in other words whether they are activated or not
(preset outputs in impulsive mode will always how their OFF status).
recstatus 123456
where:
recstatus command string
123456 access password
REPLY:
As a reply a string containing SMS activating messages regarding channels and showing their ON/OFF
status is sent
Note: To preset the channel operating modes (monostable/bistable/timed) see instructions of the RR 4
receiver.
POSSIBLE ERROR REPLIES:
The system sends the following error messages, through SMS.
“COMMAND MESSAGE NOT SET”
Check the syntax of the command string
“NO PASSWORD FOUND”
Check the syntax of the password conguration command
“COMMAND EXECUTION ERROR”
The command was not executed
“SYNTAX COMMAND ERROR”
The command is correct, but the parameter syntax is incorrect
“PASSWORD ERROR”
Check password
“ERROR UNKNOWN”
General error
“ERROR, MEMORY FULL”
Receiving memory is full. No other remote control number can be memorised
“COMMAND UNKNOWN”
The control signal is not recognized
“PHONE NUMBER NOT PRESENT”
The telephone number to be cancelled is not stored in memory
“ERROR INTERNATIONAL DIALING CODE”
Check the syntax of the memorised numbe
“UNAVAILABLE TELEPHONE NUMBER”
The command was sent by a number which is memorised, but not enabled
10
11

ALARM FUNCTION
An alarm device (Normally Closed contact) can be branched between pin 4 and 5 of the ADV terminal board
of the receiver. If the alarm triggers (the contact opens), the gsm module will send an alarm signal to the cell
phone numbersenabled for this function.
The warning signal consists in a phone call to the rst number stored in memory and enabled for this func-
tion (the order is determined by the memorisation order of the numbers in the SIM memory). The one who
receives the telephone call can disconnect the call and the alarm will stop. Otherwise, after 30 seconds, the
call will be disconnected and the second number enabled will be called, and so on.
Note: to stop the alarm by disconnecting the telephone call, the cell phone must have the telephone an-
swering function disabled.
To enable the telephone number for the receipt of the alarm signal, send the following command “adda-
larmnum” as described hereunder:
addalarmnum 123456 +NN3391234567,+NN3391234568,+NN3391234569 etc
where:
addalarmnum command string
123456 access password
+NN3391234567 telephone number with international code*, if more than one number must
be typed in with one single message, it is sucient to separate the numbers
with “,”
the number +NN3391234567 (and following) will be called if an alarm occurs
*In this case, the international code must be entered so that the alarm call can reach the user even if he is
in a foreign country, different from the country in which the CALL device is installed.
Any number can be reached by an alarm signal.
If the number is already stored in memory, it must be in any case re-entered with the addalarmnum func-
tion.
To erase the telephone number from the list of enabled numbers for alarm, use the delnum function.
In this way, the number will be erased. The corresponding number, added with the addnum function, will
be erased as well.
When the red LED of the gsm module triggers, it switches on with xed light and it will switch off when so-
meone disconnects the call or when all listed numbers have been called.
12
13

RADIO RECEIVER MODULE
In this second part, the four channel radio receiver functions are described such as wire connections, output
conguration, memorising of transmitters, etc..
SPECIFICATIONS
- Four output, independent and freely congurable channels
- Rolling code radio receiver - 433.92MHz frequency
- Programming through built-in LCD display
- Standard memory for 512 transmitters. It can be replaced with MEM2048 module for 2048 transmitters
- Versions with 230VAC, 115VAC or 24VAC/CC power supply are available.
- Input for 12VDC emergency battery, with automatic charge.
INPUT/OUTPUT FUNCTIONS
Input, No. Function Description
1-2 Power supply Input, 230Vac 50Hz (1-Phase/2-Neutral) in the 230V version
Input, 115Vac 60Hz (1-Phase/2-Neutral) in the 115V version
Input, 24 Vac/dc (1+ /2 -) in the 24V version
3-4 Channel 1 Output, channel 1. 230 Vac max 5A.
Normally Open (N.O.) Contact, switchable in Normally Closed (N.C.)
through jumper 1.
5-6 Channel 2 Output, channel 2. 230 Vac max 5A.
N.O. Contact, switchable in N.C. through jumper 2.
7-8 Channel 3 Output, channel 3. 230 Vac max 5A.
N.O. Contact switchable in N.C. through jumper 3.
9-10 Channel 4 Output, channel 4. 230 Vac max 5A.
N.O. Contact, switchable in N.C. through jumper 4.
11-12 Antenna Antenna connection of the built-in radio module
(11-screen/12-signal).
13-14 Battery Input for emergency battery, 12Vdc (13:- / 14:+).
It allows the operation of the receiver in case of power failure of the
mains, During the mains operation the battery is recharged.
Recharge time, about 15 hours for a battery 12V/1,2Ah.
Note:
The U2 memory can contain 512 rolling-code, 433.92MHz, transmitters maximum. If necessary, it can be
replaced with item MEM2048 which can contain up to 2048 different codes.
PROGRAMMING
The programming of the various functions of the control unit is carried out by using the LCD display in the
receiver and presetting the desired values in the programming menus described hereunder.
1 - Press the <PG> key, the display shows the rst Parameters Menu “PAR”.
2 - By using the keys <+> or <->, select the desired Menu (PAR>>LOG>>RADIO>>....).
3 - Press the <PG> key, the display shows the rst function available on the Menu.
4 - By using the keys <+> or <->, select the function to be modied.
5 - Press the <PG> key, the currently preset value for the selected function is displayed.
6 - By using the <+> or <-> keys, select the value to be assigned to the function.
7 - Press the <PG> key, “PRG” is displayed which means the programming has been successful.
Note:
You can return to the upper menu without making changes if you press the <+> and <-> keys simultaneously
in a Function Menu.
If you press the <+> and <-> keys simultaneously when the display is switched off, the card software version
is shown. Press PG to select the desired value. OK is shown to conrm a successful programming.
If either the <+> key or the <-> key are kept pressed, the increase/reduction of numeric values is accelerated
in the Time Menu.
12
13

After 60 sec wait, the receiver exits the programming mode and the display switches off.
Each single function, which is available in the control unit, is described in the following tables
PARAMETERS
MENU FUNCTION
MCH1
The operating mode of channel 1 is preset.
The descriptions of the single submenus are shown hereunder:
IMp Monostable. The relay activates for 1 sec when the corresponding key is pressed;
then the relay returns to its original status.
TG Bistable. When the associated key in the transmitter is pressed, the relay activates.
It remains in its new status until the key is pressed again.
time
Timed. The relay activation time can be preset within a range of 1 to 600 seconds
(10 min).
Select the desired activation time between 1 and 600 seconds, then press OK to
store the val ue into memory.
MCH2 Same operating modes preset for MCH1.
MCH3 Same operating modes preset for MCH1.
MCH4 Same operating modes preset for MCH1.
RADIO
MENU FUNCTION
Add
Menu to type in the transmitter codes in memory.
The submenus are described hereunder:
CH1 The key is associated to channel 1. Press, within 5 sec, the transmitter key which is
to be associated to channel 1.
CH2 The key is associated to channel 2. Press, within 5 sec, the transmitter key which is
to be associated to channel 2.
CH3 The key is associated to channel 3. Press, within 5 sec, the transmitter key which is
to be associated to channel 3.
CH4 The key is associated to channel 4. Press, within 5 sec, the transmitter key which is
to be associated to channel 4.
DEL
Menu to erase previously typed in transmitter codes from memory.
The single submenus are described hereunder:
code
The receiver is in a waiting mode, waiting for a memorized transmitter key to be
pressed.
The transmitter is erased from the receiver memory.
indh Remove a transmitter code for which the position in memory is know, see function
FIND>>Code.
res The receiver memory is completely erased. All transmitter codes and relevant associations
and channel parameters are cancelled. A conrmation of the operation is being asked.
find
Search Menu for transmitter codes stored in memory.
The single submenus are described hereunder:
Code The receiver is waiting for a code. Press any key on the transmitter; if this is stored
its position in memory is displayed.
N Tx The number of transmitter codes stored in the receiver memory is displayed.
14
15

14
15

