Berbel Emotionline Series User manual

EN Wall hood
Emotionline
EN Operating and installation instructions for the models
BWH 60 EL
BWH 70 EL
BWH 80 EL
BWH 90 EL
BWH 120 EL
6004347_0

2
6004347_0 – 27.09.2018
Document information
Operating and installation instructions for:
yBWH 60 EL E01 wall hood
yBWH 70 EL E01 wall hood
yBWH 80 EL E01 wall hood
yBWH 90 EL E01 wall hood
yBWH 120 EL E01 wall hood
Descriptions are identical for all models.
Differences are noted separately.
Illustrations show:
yEmotionline BWH 90 EL wall hood
yOriginal instructions.
yPart of the product.
yCopyright protected.
yDuplications, re-printing and distribution only with
permission.
ySubject to alteration.
Safety information
DDANGER!
Notes with the word DANGER warn of a hazardous situation
that results in serious injuries or death.
DWARNING!
Notes with the word WARNING warn of a hazardous situation
that could result in serious injuries or death.
DCAUTION!
Notes with the word CAUTION warn of a situation that could
result in minor injuries.
DATTENTION!
Notes with the word ATTENTION warn of a situation that
could result in damage to property or to the environment.
Symbol clarification - text
☞Handling requirement
yListing
DReference to another point in this document
Reference to other documents that should be observed
Symbol clarification - illustrations
x
A
B
1.
2.
Highlighting of the parts involved in the action with
shading
1. Handling steps with numbering
APart designations with upper case characters
xDimensions with lower case characters or units in mm
Movement and direction arrows

3
6004347_0 – 27.09.2018
EN
Table of contents
1. Safety information ............................ 4
1.1 Proper intended use . . . . . . . . . . . . . . . . . . . . . 4
1.2 Authorised target groups . . . . . . . . . . . . . . . . . . 4
1.3 General safety instructions . . . . . . . . . . . . . . . . . 4
2. Product information ........................... 5
2.1 Functional principle . . . . . . . . . . . . . . . . . . . . . 5
2.2 Operating modes. . . . . . . . . . . . . . . . . . . . . . . 5
2.2.1 Recirculated air mode.........................5
2.2.2 Extracted air mode ............................5
2.2.3 Hybrid mode..................................5
2.3 Product overview . . . . . . . . . . . . . . . . . . . . . . . 6
2.4 Scope of delivery . . . . . . . . . . . . . . . . . . . . . . . 6
2.5 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . 7
3. Installation .................................... 8
3.1 Safety instructions for installation. . . . . . . . . . . . . 8
3.2 Requirements for the installation location . . . . . . . 8
3.3 Requirements for individual operating modes. . . . . 9
3.3.1 Requirements for recirculated air mode .......9
3.3.2 Requirements for extracted air mode..........9
3.3.3 Requirements for hybrid mode................9
3.4 Requirements for the exhaust air ducting
(only for extracted air mode or hybrid mode) . . . . . 9
3.5 Installation procedure . . . . . . . . . . . . . . . . . . . .10
3.5.1 Preparation for installation ..................10
3.5.2 Unpack the device ..........................10
3.5.3 Removing the lower section, bulging
edge and Capillar Trap ......................11
3.5.4 Hang the device in place....................12
3.5.5 Connect accessories ........................14
3.5.6 Fit chimney side parts.......................15
3.5.7 Install filter (with recirculating and hybrid
operation) ..................................16
3.5.8 Connect exhaust air ducting (with
exhausted air and hybrid operation).........17
3.5.9 Establish electrical power supply ............17
3.5.10 Fit chimney front panel .....................18
3.5.11 Insert the Capillar Trap, bulging edge and
lower section ...............................19
3.5.12 Check and carry out commissioning ........19
4. Operation ....................................20
4.1 Safety instructions for operation . . . . . . . . . . . . .20
4.2 Operating the device . . . . . . . . . . . . . . . . . . . .21
4.2.1 Normal operation ...........................21
4.2.2 Extraction mode / recirculated air mode
changeover .................................22
4.2.3 Filter filling indicator ........................22
4.2.4 Cooktop lighting............................22
4.2.5 AutoRun ....................................22
4.2.6 Run-on function ............................23
4.2.7 Special functions............................23
4.3 Configuring the device . . . . . . . . . . . . . . . . . . .24
5. Cleaning .....................................25
5.1 Safety information for cleaning . . . . . . . . . . . . . .25
5.2 Cleaning procedures. . . . . . . . . . . . . . . . . . . . .25
6. Maintenance .................................27
6.1 Safety instructions for maintenance . . . . . . . . . . .27
6.2 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . .27
6.2.1 Changing the lamps ........................27
6.2.2 Replacing filter filling (with recirculating
and hybrid mode)...........................27
6.3 Fault rectification . . . . . . . . . . . . . . . . . . . . . . .29
7. Dismounting .................................30
8. Disposal ......................................31
8.1 Dispose of packaging . . . . . . . . . . . . . . . . . . . .31
8.2 Dispose of the device . . . . . . . . . . . . . . . . . . . .31
9. Annex ........................................32
9.1 Product data sheet . . . . . . . . . . . . . . . . . . . . . .32
9.2 Contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33

4
Safety information
6004347_0 – 27.09.2018
1. Safety information
1.1 Proper intended use
The device serves to extract cooking vapours.
The device is intended exclusively for private domestic use.
The device must only be used with original filters from the
manufacturer.
It is only permitted to use the device when it is in technically
flawless condition and after correct installation.
Any other use shall be considered improper use.
The reading and observance of this manual are also included
in the proper use of the device.
1.2 Authorised target groups
Electrical work only to be undertaken by qualified electricians
in accordance with DIN VDE 0100. Requirements on qualified
electricians:
yKnowledge of the basics of electrics.
yKnowledge of country-specific regulations and standards
(e.g. in Germany, DIN VDE 0100, part 701).
yKnowledge of the applicable safety regulations.
yKnowledge of the relevant legal requirements for gas
installations (e.g. in Germany the technical rules for gas
installations TRGI).
yKnowledge of this manual.
Installation and repair only by qualified specialist personnel.
Requirements on qualified specialist personnel:
yKnowledge of the regulations on safety at work.
yKnowledge of fastening systems.
yBasic knowledge of ventilation systems.
yExperienced in using electrical and mechanical tools.
yAbility to read technical drawings.
yKnowledge of this manual.
Operation, cleaning and maintenance by the user.
Requirements for the user:
yKnowledge of this manual.
There are separate requirements for the following users:
yChildren from 8 years and older.
yPersons with restricted physical, sensory or mental
capabilities.
yPersons with a lack of experience and knowledge.
These users are only permitted to carry out operation,
cleaning and maintenance. Special requirements:
yUsers are supervised.
yUsers are instructed with regard to safe use of the device.
yUsers understand the hazards involved with the device.
yChildren may not play with the device.
1.3 General safety instructions
DWARNING!
Hazard through a disregard of the operating and
installation instructions!
This manual contains important information for the safe
handling of the device. Separate reference is made to
possible hazards.
☞Read through this manual thoroughly.
☞Follow the safety instructions in this manual.
☞Store the manual in an accessible location.
Naked flames can damage the device and can cause fires.
yGas operation only with low gas flames (not rising above
the edge of the base of the pots).
yDo not flambé underneath the device.
yNo unattended deep frying underneath the device.
The use of the device is forbidden under the following
circumstances:
yIf necessary safety devices are missing (e.g. low-pressure
monitor whilst using a heating point which uses air from
the room as its oxygen supply).
yIf essential approvals are missing (e.g. from
chimneysweeps).
yIn potentially explosive atmospheres.
yIf the device or individual components are damaged.
yIn the event of unauthorised alterations or changes to the
device.
yIf liquid has penetrated the device.
yWhen heavily soiled.
yFor children under 8 years old and persons who would
not be able to properly assess the hazards associated with
handling the device.
The manufacturer accepts no liability for damage occurring in
the following circumstances:
yDisregard of this manual.
yImproper use of the device.
yImproper installation and handling of the device.
yUse of the device by unauthorised target groups.
yBypassing safety equipment on the device.
yUse of replacement parts that were not produced or
approved by the manufacturer.
Further safety instructions can be found in the respective
relevant chapters of this manual.
D“3.1 Safety instructions for installation” (page 8).
D“4.1 Safety instructions for operation” (page 20).
D“5.1 Safety information for cleaning”(page 25).
D“6.1 Safety instructions for maintenance” (page 27).

5
Product information
6004347_0 – 27.09.2018
EN
2. Product information
2.1 Functional principle
Centrifugal force
yCooking vapours are drawn through a gap and into the
hood where they are accelerated and routed through
bends.
yThe resultant centrifugal force ejects particles of dirt
(e.g. particles or grease and oil) out of the air.
yThe dirt particles are separated out and collected on the
upper and lower section as well as a catchment screen
(“Capillar Trap”).
2.2 Operating modes
The device is suitable for the following operating modes:
yRecirculated air mode
yExtracted air mode
yHybrid mode
2.2.1 Recirculated air mode
The filter filling in the recirculated air filter neutralises any
smelly odours present. The odour-free, cleaned room air is
fed back into the room. The humidity in the room can be
reduced with the fresh air feed.
In recirculated air mode, it is necessary to use the run-on
function so that the device can remove the remaining
odours. Using the run-on function increases the life of the
filter filling. The filter filling must be replaced at regular
intervals.
2.2.2 Extracted air mode
The cleaned room air can be routed to the outside via the
building structure (e.g. ducting, chimney).
With extracted air mode an adequate fresh air supply is
required. The device can only extract the amount of air to the
outside that is present in the room or which is drawn into the
room.
2.2.3 Hybrid mode
In hybrid mode, it is possible to select flexibly between
recirculated air mode and extracted air mode.
In extracted air mode, the cleaned room air is routed to the
outside through the wall box which opens automatically.
Extracted air mode is recommended in summer or with
particularly intensive frying.
In recirculated air mode the wall box remains closed. The
filter filling in the hybrid filter neutralises any smelly odours
present. The odour-free, cleaned room air is fed back into the
room.
The recirculated air mode is recommended in winter if no
warm room air is to be surrendered to the outside.

6
Product information
6004347_0 – 27.09.2018
2.3 Product overview
D
C
E
F
A
BH
G
A Chimney
B Hood body
C Upper section with bulging edge (removable)
D Capillar Trap (removable)
E Lower section (removable)
F Ratings plate (in the air induction shaft of the Capillar Trap)
G Control panel
H Hob lighting
A
B
C
D
A Connection terminals for wall box, window contact switch
(multifunction contact) and bus connection
B Fan outlet with guide for filter or exhaust air ducting
C Adjusting screws for alignment
D Connector for the mains cable
2.4 Scope of delivery
A
B
E
I
F
G
H
D
C
A Hood body
B Wall bracket
C Chimney side parts (with ventilation slots with the version
for recirculated air mode)
D Chimney front panel
E Mains cable with plug and cold device plug
F 4 rounded head screws (cross recess) M4 x 5
G 6 nylon wall plugs 8 mm
H 6 Torx screws TX30 with integrated washers
I Operating and installation instructions
The fastening materials are only suitable for solid walls.
Further accessories may be required depending on the
operating mode.

7
Product information
6004347_0 – 27.09.2018
EN
2.5 Technical data
BWH60ELE01 BWH70ELE01 BWH80ELE01 BWH90ELE01 BWH120ELE01
Connection
voltage
230 V /
50 Hz
230 V /
50 Hz
230 V /
50 Hz
230 V /
50 Hz
230 V /
50 Hz
Total power 177 W 177 W 177 W 177 W 181 W
Fan power
consumption 170 W 170 W 170 W 170 W 170 W
Lighting
LED
6,9 W,
306 lx
LED
6,9 W,
260 lx
LED
6,9 W,
244 lx
LED
6,9 W,
262 lx
LED
10,9 W,
368 lx
Width 599
mm
699
mm
799
mm
899
mm
1199
mm
Depth 515
mm
515
mm
515
mm
515
mm
515
mm
Height in
recirculated
air mode with
recirculated air
filter BUF 150 +
715 -
1015
mm
715 -
1015
mm
715 -
1015
mm
715 -
1015
mm
715 -
1015
mm
Height in
recirculated
air mode with
recirculated air
filter permalyt
815 -
1015
mm
815 -
1015
mm
815 -
1015
mm
815 -
1015
mm
815 -
1015
mm
Height in
extracted air
mode
665 -
1015
mm
665 -
1015
mm
665 -
1015
mm
665 -
1015
mm
665 -
1015
mm
Height in hybrid
mode
865 -
1015
mm
865 -
1015
mm
865 -
1015
mm
865 -
1015
mm
865 -
1015
mm
Net weight 25 kg 25.5 kg 26 kg 27.5 kg 31 kg
Information about energy consumption can be found in the
product fiche.
D„9.1 Product data sheet“
Information on the model (e.g. serial number, year of
construction) is quoted on the front panel.
D“2.3 Product overview”(page 6).

8
Installation
6004347_0 – 27.09.2018
3. Installation
3.1 Safety instructions for installation
DWARNING!
Hazard through disregard of the installation instructions!
This chapter contains important information for the safe
installation of the device.
☞Read through this chapter carefully before installing the
device.
☞Follow the safety instructions.
☞Carry out the installation as described.
yInstallation only by qualified specialist personnel.
D“1.2 Authorised target groups”(page 4).
yElectrical work only to be undertaken by qualified
electricians.
D“1.2 Authorised target groups”(page 4).
yInstallation requires two persons.
yWhen working at heights, ensure good stable footing
(e.g. stable stepladder).
yThe hob and other parts that can be touched must be
allowed to cool prior to installation.
yStore the film or other parts of the packaging in a location
which is inaccessible to children.
yThe device must be in an undamaged and fault-free
condition prior to installation.
yCables must not be kinked, crushed or damaged.
yNever open the fan housing.
yThe power supply voltage must match the voltage
information quoted on the ratings plate.
D“2.5 Technical data”(page 7).
yEnsure that the power supply is stable and remains so
prior to the installation.
Connect the power supply only when instructed to do so
in the installation instructions.
3.2 Requirements for the installation location
DWARNING!
Risk of death due to improper installation!
Disregard of the ambient conditions can lead to hazardous
situations, e.g. in the handling of electrical power or gas.
☞Make sure that the requirements for the installation
location are complied with.
yDo not install in potentially explosive atmospheres.
yWith simultaneous use of a heating point which uses air
from the room as its oxygen supply (e.g. chimneys):
yA safety device is absolutely essential.
yThe safety device (e.g. under-pressure monitor P4,
inspected in accordance with DIN 18841:2005-12 TÜV
and in accordance with DVGW-VP121) must prevent
gases being drawing to the room.
yAn approval for commissioning (e.g. from a
chimneysweep) must be available.
yInstallation is only permitted on structural building
elements capable of bearing the load (solid structure).
yIf it is necessary to break through the wall:
A wall break-through influences the structural integrity
of the building. This work must only be carried out by a
specialist.
yIf installed above fireplaces that use solid fuels (e.g. coal
stove):
The fireplace must have a sealed cover which cannot be
removed. Otherwise there is a fire risk due to flying sparks.
Applicable legal and country-specific regulations must be
observed.
yThe air flowing out must be able to dissipate unimpeded.
Do not impede the air flow, e.g. through the installation of
objects on or above the device.
yMake sure that the building electrical supply is properly
earthed.
yThe power supply voltage present must match the
voltage information quoted on the ratings plate.
yThere must be an electrical power outlet in the vicinity of
the hood installation.
yThe mains plug must be accessible after the installation
of the hood. Alternatively, all-pole isolating device (with a
contact gap of at least 3 mm) must be provided.
Country-specific, legal provisions must be observed.

9
Installation
6004347_0 – 27.09.2018
EN
3.3 Requirements for individual operating modes
Further accessories may be required depending on the
operating mode.
3.3.1 Requirements for recirculated air mode
yRecirculated air filter at the fan outlet.
yCross-section of the ventilation slot in the superstructure
larger than 300 cm2.
yFilter filling freely accessible for changing.
3.3.2 Requirements for extracted air mode
yExhaust air ducting at the fan outlet.
D“3.4 Requirements for the exhaust air ducting
(only for extracted air mode or hybrid mode)”
(page 9).
yDiameter of the exhaust air ducting at least 150 mm
(corresponds to a surface area of approx. 177 cm2).
yAdequate fresh air supply is assured through the
installation of the necessary accessories.
yWindow contact switch.
yWall box.
3.3.3 Requirements for hybrid mode
yHybrid filter at the fan outlet.
yConnection of the exhaust air ducting to the hybrid filter.
D“3.4 Requirements for the exhaust air ducting
(only for extracted air mode or hybrid mode)”
(page 9).
yCross-section of the ventilation slot in the superstructure
larger than 300 cm2.
yDiameter of the exhaust air ducting at least 150 mm
(corresponds to a surface area of approx. 177 cm2).
yFilter filling freely accessible for changing.
yAdequate fresh air supply is assured through the
installation of the necessary accessories.
yWindow contact switch.
yWall box BMK-F 150.
3.4 Requirements for the exhaust air ducting
(onlyforextracted air mode or hybrid mode)
DWARNING!
Fire hazard and asphyxiation hazard due to improper
installation!
When using the exhaust air ducting with other devices
or when connecting an active exhaust air channel
(e.g. chimney), gases or smoke can be drawn into the room.
☞Make sure that the requirements for the exhaust air
ducting are complied with.
yThe exhaust air ducting is used exclusively by this device.
yThe exhaust air ducting is made of non-combustible
material in accordance with DIN 4102 class 1.
yWhen using a chimney as the exhaust air duct:
yThe chimney must not be used by other devices.
yThe extracted air must be introduced into the
chimney using a 90° bend pointing upwards.
yApproval by a master chimney sweep.
yWhen routing the exhaust air ducting through the roof or
the outside wall:
yThe cross-section must not be smaller than that of the
fan outlet.
yInstallation of condensed water collector in the
exhaust air ducting in order to prevent water damage
inside the device. The condensed water collector must
be adequately dimensioned.
The cross-section, length, type and course of the exhaust
pipe affect the extraction efficiency. Changing the direction
of the air too severely leads to a loss of performance and to
noise.
To optimise the device performance:
yKeep the exhaust air ducting as short as possible and
route it directly to the outside.
yThe stipulated cross-section of the exhaust air ducting is
complied with.
D“3.3 Requirements for individual operating modes”
(page 9).
yExclusive use of ducts and bends with smooth inner
surfaces.
In order to avoid turbulence or backpressure in the
transported air - do not use:
ySpiral hoses.
yFlexible tubes.
yFlat deflection pieces.
ySharp-edged exhaust air channels.
The exhaust air ducting must be in place before installing the
device.

10
Installation
6004347_0 – 27.09.2018
3.5 Installation procedure
Short overview:
1. Preparation for installation
2. Unpack the device
3. Removing the lower section, bulging edge and
Capillar Trap
4. Hang the device in place
5. Connect accessories
6. Fit chimney side parts
7. Install filter (with recirculating and hybrid operation)
8. Connect exhaust air ducting (with exhausted air and
hybrid operation)
9. Establish electrical power supply
10. Fit chimney front panel
11. Insert the Capillar Trap, bulging edge and lower section
12. Check and carry out commissioning
3.5.1 Preparation for installation
☞Familiarise yourself with the installation situation and the
associated documents.
yDevice and instructions.
yAccessories.
yInstallation location.
yIntended operating mode.
☞Assemble the tools and materials required:
yStable stepladder
yFolding rule or measuring tape
yPencil
ySpirit level
yPhillips head screwdriver, size 2
ySlotted screwdriver SL 2.5 x 0.4
yØ 8 mm masonry bit
yHammer drill
y10 mm spanner
yProtective material (e.g. thick cardboard) for the hob
and the worktops
☞Keep the installation area free of objects that could be in
the way or that could be damaged.
☞Make sure that the hob and other parts that could be
touched have cooled down.
☞Protect the hob and other surfaces in the installation area
(e.g. with thick cardboard).
☞Ensure that the power supply is switched off and remains
so. Connect the power supply only when instructed to do
so in the installation instructions.
If accessories (e.g. wall box, window contact switch) are
required for the installation:
Observe the instructions for the accessories.
☞Ensure that the accessories are correctly installed and
ready for connection.
☞Ensure that the connection cables from accessories are
correctly routed and accessible.
3.5.2 Unpack the device
DATTENTION!
Hazard of glass breaking or other damage due to
incorrect handling!
The device and its surfaces can be damaged when being
unpacked or transported.
☞Do not cut into the protective cardboard packaging.
☞Keep objects that could scratch the device far away from
it (e.g. tools, belt buckles).
☞Unpack the device and all accompanying parts carefully.
☞Place the device on its back on a firm, clean and
protective surface (e.g. thick cardboard).
☞Check the device and its constituent parts for damage.
☞Check the delivery is complete.
D“2.4 Scope of delivery” (page 6).
If parts are missing or damaged:
☞Please consult your dealer or customer services.
☞Remove the packaging material.
D“8. Disposal” (page 31).

11
Installation
6004347_0 – 27.09.2018
EN
3.5.3 Removing the lower section, bulging edge and
CapillarTrap
DATTENTION!
Danger of property damage through falling parts!
When working on the device, parts of the device or tools
could fall and damage the kitchen equipment.
☞Protect the cooled hob and other surfaces in the cooking
area (e.g. with thick cardboard).
☞Fold the lower section down.
☞Lift the lower section up approx. 20 mm at the sides with
both hands.
☞Pull the lower section out forwards.
The bulging edge is attached and held in the device by
magnets.
☞Pull the bulging edge from the upper section.
The Capillar Trap is inserted and is held in the device through
a side lock.
☞Grasp the Capillar Trap on its sides with both hands.
☞Pull the Capillar Trap out.

12
Installation
6004347_0 – 27.09.2018
3.5.4 Hang the device in place
The device is designed to be hung on walls. The chimney can
be adapted to the ceiling height by pulling it out.
When mounting on a solid wall:
☞Make sure that the wall has sufficient load bearing
capacity.
☞Use the fastening materials provided.
With different installation situations:
☞Enquire about alternative fastening systems (e.g. consult
with your architect).
☞Only use fastening hardware suitable for the type of wall.
xy
460
35
270
495
31
290
==
400
Safety distance (x):
yRecommendation 650 mm.
yWith gas hobs, at least 650 mm.
Distance from upper edge of body to ceiling (y) =
Length of the chimney side parts + 2 mm
☞Determine the hanging position.
☞Ensure that the wall bracket is correctly positioned:
yIf dimension “y”is undercut then the front panel
cannot be opened.
☞Make sure that the safety distance is complied with.
DWARNING
Risk of death due to explosions or electric shock!
Drilling through gas, water or electrical lines can lead to
hazardous situations.
☞Ensure that there are no lines in the wall at the fastening
points.
Ø 8
☞Determine the locations of the fastening points and mark
them.
☞Drill the holes in the wall.
☞Insert the wall plugs into the holes.
☞Screw the wall bracket on loosely.

13
Installation
6004347_0 – 27.09.2018
EN
aa
bb
a = 7
b = 3-6
The top fastening screws should only be tightened once the
device has been aligned.
The lower fastening screws prevent the device pulling away
from the wall and are no longer accessible after the device is
hung in place.
☞Tighten the mounting screws appropriately.
DWARNING!
Danger of injuries through improper handling!
Hanging the device requires a great deal of physical exertion
due to its size and weight. If the device falls down, serious
injuries are possible.
☞Two persons are required to hang the device.
☞Ensure stable footing when hanging the device.
☞Ensure that no other people are in the working area.
DATTENTION!
Danger of property damage through improper handling!
Hanging the device requires a great deal of physical exertion
due to its size and weight. If the device falls, the device,
kitchen furnishings and other objects could be damaged.
☞Cover the cooled hob.
☞Keep the installation area clear.
☞Hang the device on the mounting points.
1.
2.
3.
2.
3.
☞Check the horizontal alignment of the device.
☞Align the device with the adjusting screws.
☞Tighten the mounting screws.

14
Installation
6004347_0 – 27.09.2018
3.5.5 Connect accessories
Depending on the installation situation, accessories may be
connected to the hood:
yWall box
yRecirculated air filter permalyt
yWindow contact switch
yUnder-pressure monitor
Observe the instructions for the accessories.
12 V DC
4 5
6 7 8 9
BMK-F F-K
2 31
D
A
BC
E
F
G
H
12 V DC
GND X1 X1 X1 X1 X1 + 5 V
MFK MFK BMK2 BMK1
ST3
+
+
–
–
I
A Control box
yBMK1: Wall sleeve contact, optocoupler collector,
max. 12 mA / 12 V DC, safe galvanic separated
yBMK2: Wall sleeve contact, optocoupler emitter,
max. 12 mA / 12 V DC, safe galvanic separated
B Terminal “BMK-F” for the wall box connection
C Terminal “F-K”(multifunction contact) for the window
contact switch or under-pressure monitor connection
D Control line from the wall box
E Wall box
F Wall box power unit
G Window contact switch
H Control line from the window contact switch
I Bus connection
Connection is implemented via cable terminals on a
detachable connector on the fan housing.
DATTENTION!
Risk of damage through incorrect connection!
A mix-up of the control wires can result in damage to the
electronics.
☞Be careful not to mix up connections when connecting
the control wires: Core 1 on terminal 1, core 2 on
terminal 2.
1.
2.
1.
Wall box
☞Connect the wall box as follows:
yCore 1 on terminal 1
yCore 2 on terminal 2
yThe wall box is closed when the control contacts are
open.
yThe wall box is open when the control contacts are
closed.
Window contact switch
☞Connect the window contact switch as follows:
yBlue/white core to terminal 3
yBrown/green core to terminal 4
yThe hood‘s fan is only operational when the window is
open.
Under-pressure monitor
yThe hood‘s fan is only operational when no critical under-
pressure is determined in the room.

15
Installation
6004347_0 – 27.09.2018
EN
3.5.6 Fit chimney side parts
DATTENTION!
Danger of damage through improper handling!
The body of the hood and the chimney could be damaged
by movements during the installation.
☞Keep a distance between the chimney and the body of
the hood.
☞Keep objects that could scratch the device far away from
it (e.g. tools, belt buckles).
The chimney consists of two side parts and the front panel.
The side parts are fitted in this step. Inserting the front panel
only takes place after fitting the filter and after connecting
the exhaust air ducting.
☞Bend the metal plates on the side parts, so that a
90° angle results.
☞Insert the side parts such that the holes on the underside
fit over the screwed end on the hood body.
☞Make sure that the fastening holes in the side parts are
flush with the threaded holes in the wall brackets.
☞Screw the side parts onto the wall bracket.
☞Tighten the screws for the wall fastening of the wall
bracket. If necessary, the position can be adjusted via
slotted holes.

16
Installation
6004347_0 – 27.09.2018
3.5.7 Install filter (with recirculating and hybrid
operation)
There is a pipe connection (Ø 150 mm) on the fan housing as
an installation aid for the installation of the filter.
The filter is placed correctly when the bottom edge of the
filter is parallel to the top edge of the fan‘s housing and the
gap is approximately 5 mm wide.
Recirculated air mode
5
☞Place the recirculated air filter onto the guide on the fan
housing from above.
☞Ensure that the recirculated air filter is correctly installed.
Hybrid mode
5
☞Place the hybrid filter onto the guide on the fan housing
from above.
☞Ensure that the hybrid filter is correctly installed.

17
Installation
6004347_0 – 27.09.2018
EN
3.5.8 Connect exhaust air ducting (with exhausted
air and hybrid operation)
Extracted air mode
2.
1.
2.
☞Fit the exhaust air ducting onto the guide on the fan
housing from above.
☞Seal the transition between the exhaust air ducting and
the guide with the help of sealing tape (accessory).
☞Ensure that the exhaust air duct is correctly fitted.
Hybrid mode
☞Fit the exhaust air ducting onto the collar of the hybrid
filter from above.
☞Ensure that the exhaust air duct is correctly fitted.
3.5.9 Establish electrical power supply
☞Observe the voltage specifications on the ratings plate.
☞Plug the connecting cable mains plug into the socket.
☞Route the cable such that it is not kinked, crushed or
damaged and so that it will not get in the way when
replacing the filter filling.
☞Make sure that the device can be disconnected on all
poles from the electricity supply after installation.
The device is ready for operation.

18
Installation
6004347_0 – 27.09.2018
3.5.10 Fit chimney front panel
Danger of damage through improper handling!
The body of the hood and the chimney could be damaged
by movements during the installation.
☞Keep a distance between the chimney and the body of
the hood.
☞Keep objects that could scratch the device far away from
it (e.g. tools, belt buckles).
☞Unscrew the knurled nut from the wall bracket.
☞Make sure that the closure on the front panel is open.
☞Insert the front panel such that the holes on the
underside fit over the metal plates on the side parts.
☞Fit the free end of the retaining rope onto the threaded
bolt on the wall bracket.
☞Screw the knurled nut onto the wall bracket until hand-
tight.
☞Press the front panel up between the side parts until the
closure can be heard to latch. If necessary, the closure can
be adjusted via slotted holes.

19
Installation
6004347_0 – 27.09.2018
EN
3.5.11 Insert the Capillar Trap, bulging edge and
lower section
After the installation, the parts lying inside should be re-fitted.
☞Insert the Capillar Trap into the mounting slot with both
hands.
☞Push the Capillar Trap upwards until it latches into place.
☞Place the bulging edge onto the upper section.
☞Check whether the bulging edge is correctly placed and
held by the magnets.
☞Guide the lower section into the device from below, until
the guide grooves of the lower section are in front of the
guide pins on both sides.
☞Press the lower section backwards into the device.
☞Pull the lower section downwards until it latches into
place.
☞Check that the lower section can be moved easily.
☞Pivot the lower section upwards until both magnetic
fasteners can be heard to click into place.
3.5.12 Check and carry out commissioning
DATTENTION!
Risk of disruptions due to moisture in the device!
If the device is moved from a cold environment into a hot
one, condensation may form inside.
☞Wait about 2-3 hours before bringing the device into
service.
☞Remove the protective film from the device.
☞Check that the mains plug is freely accessible or that
an all-pole isolating device (min. 3 mm contact gap) is
present.
☞Check that the mains cable and the electrical connection
cable are not kinked, crushed or damaged.
☞Ensure that air outlets are not closed or covered.
☞With recirculated air devices: Make sure that the
ventilation slots are free.
☞Check the correct functioning of the device.
D“4. Operation” (page 20).

20
Operation
6004347_0 – 27.09.2018
4. Operation
4.1 Safety instructions for operation
DWARNING!
Hazard through a disregard of the operating
instructions!
This chapter contains important information for the safe
operation of the device.
☞Read through this chapter carefully before operating the
device.
☞Follow the safety instructions.
yOperation only by authorised users.
D“1.2 Authorised target groups”(page 4).
yNot to be operated by children under 8 years old or
people who cannot assess the hazards of handling the
device.
yThe extractor hood must not be operated unsupervised.
yDo not use during a fire or when there is an imminent
danger of fire (e.g. a smell of gas).
yGas operation only with low gas flames (not rising above
the edge of the base of the pots). Naked flames can
damage the device and can cause fires.
yDo not flambé underneath the device. Fire hazard.
yNo unattended deep frying underneath the device.
yWhen in use, the cooktop and other parts that could be
touched can become very hot. There is a risk of burning.
yGrease residues should be removed. Grease residues pose
a fire hazard.
yNo moisture in the device.
yAvoid dripping or splashing water.
yContainers with liquids (e.g. vases, bottles) must not
be placed on the device.
yDo not impede the air flow.
yDo not impede the air channel on the underside of the
device.
yUse only when the capillary trap is used and the lower
section closed.
yIn recirculated air mode:
Do not cover the air outlets (e.g. glasses/plates on or in
front of the ventilation slots). Out-flowing air must be
able to escape through the ventilation slots without
impediment. Otherwise backpressure may form. If the
cooking vapours are no longer able to escape there is a
danger of fire.
yWith exhausted air or hybrid operation:
Adequate fresh air supply must be assured.
Measures to ensure a sufficient supply of fresh air:
☞Open the windows.
☞Open the doors.
☞Ensure that the window contact switch and the wall box
are installed and ready for operation.
☞With heating points which use air from the room as their
oxygen supply (e.g. chimneys):
Make sure that the mandated safety devices are
functioning correctly.
If you switch the machine on and hear an unusually loud fan
noise:
☞Clean the device.
☞Follow the cleaning instructions.
D“5. Cleaning”(page 25).
If you switch the machine on and notice a smell:
☞Change the filter filling.
☞Follow the instructions for changing the filter filling.
D“6.2.2 Replacing filter filling (with recirculating and
hybrid mode)” (page 27).
If the control indicator for the filter filling flashes:
☞Change the filter filling.
☞Follow the instructions for changing the filter filling.
D“6.2.2 Replacing filter filling (with recirculating and
hybrid mode)” (page 27).