Sirius Satellite Radio Stone SU-DD2-L Quick start guide

SU-DD2-L
STONE
EN INSTALLATION, USE AND MAINTENANCE INSTRUCTION

2SU-DD2-L

EN
Keep these instructions for use with the ap-
pliance. If the appliance should be sold or
passed on to others, make sure that the in-
structions are passed on with it. We thank
you for taking note of these suggestions be-
fore installing and using the appliance. They
have been written for your personal safety
and the safety of others.
TO THE ATTENTION
OF THE USER
WARNING
● It is not allowed to cook food over open ames
(ambé) or operate gas hobs without pots or pans
on them under the hood itself (the ames sucked
into the hood might damage the appliance).
● Frying under the appliance must be done un-
der constant supervision as hot oils and fats may
ignite. Respect the guidelines for cleaning and
replacement of grease lters. Accumulated depo-
sits of grease are a re hazard.
● This appliance must not be used over cook tops
powered by wood or coal or in any case, over
cook tops with power levels that could damage
the appliance. Never use steam or high-pressure
devices for cleaning your hood (regulations re-
garding electrical safety).
● Never use the cooker hood without the grease
lters.
● The minimum distance between the Downdraft
(closed) and the surface above it must be at least
400 mm.
● When handling the downdraft, never put your
hands in the eld of action of the extractable unit.
Constantly seeking to improve our products, we
reserve the right to modify their technical, fun-
ctional, or aesthetic characteristics deriving from
their upgrading. In the case of the version with
external motor, fornormal downdraft operation,
it is necessary to use a suctioning unit (external
motor) made by the same manufacturer. The air
collected must not be conveyed into a ue used
for smoke or fumes from appliances powered by
anything other than electricity (central heating sy-
stems, etc.). As far as discharging exhaust air is
concerned, please follow the guide- lines given
by competent authorities.
● This product is not intended for use by people
(including children) who have reduced physical,
emotional, or mental abilities or lack of experien-
ce and knowledge unless they have been instruc-
ted in the correct use of the product. By a person
responsible for their safety and security. Children
should be supervised to ensure that they do not
play with the product. If the power cord is dama-
ged, it should only be replaced with a new cable
provided by the manufacturer or representative.
His service and by a person authorized to do so,
in order to avoid a hazard.
SAFTEY INSTRUCTIONS
These hoods have been designed for personal
use in the home. The appliance must be used by
adults. Make sure that the appliance is out of re-
ach of children and that they do not use it to play
with. Make sure that children do not operate the
controls.
● When the appliance is delivered, check the
overall appearance of the packaging. Any remar-
ks should be written on the delivery coupon, of
which you keep a copy. Your appliance is desi-
gned for normal domestic use. It is not designed
for commercial or industrial use, or for purposes
other than those for which it was designed.
● Any consequences of or damage from incorrect
installation or incorrect use of the appliance will
not be covered by the manufacturer’s guarantee.
● Do not ever change or try to change the charac-
teristics of this appliance. This would be a danger.
Repairs must be performed only by an authorised
technician. Always disconnect the hood before
carrying out cleaning or maintenance operations.
● Adequately ventilate the room when a cooker
hoodand other appliances, powered by energy
other than electricity, are used simultaneously,
so that the hood does not suck anycombustion
fumes.
It is designed to work in both suctioning mode,
with outside evacuation, and ltering mode.
3
SU-DD2-L

EN
INSTALLING THE COOKER HOOD .....................................................................................5
HOW TO USE THE COOKER HOOD .................................................................................18
Grease lter removal, mounting the activated charcoal lter ..........................................20
Electrical connection of the cooker hood ........................................................................21
HOW THE COOKER HOOD WORKS .................................................................................22
CLEANING THE COOKER HOOD .....................................................................................26
OPERATIONAL ANOMALIES .............................................................................................27
REPLACING THE LIGHT ....................................................................................................27
AFTER SALES SERVICE ...................................................................................................28
CONTENTS
4SU-DD2-L

EN
INSTALLING THE
COOKER HOOD
1. Before carrying out the appliance installation, please check that all components are not damaged, in
such a case contact your retailer and do not carry out any installation operation. Before the installation
of the Downdraft, please remove the safety piece you can see in the picture (Fig. 1).
Furthermore, please read carefully all of the following installation instructions.
• Use an air exhausting pipe whose maximum length does not exceed 5 meters.
• Limit the number of elbows in the piping,since each elbow reduces the air capacity of 1 linear meter.
(Ex. : if you use no. 2 x 90 ° elbows, the length of piping should not exceed 3 meters).
• Avoid abrupt direction changes.
• Use a 150 mm. constant diameter pipe for the whole length.
• Use piping approved by standards in force.
The manufacturer shall not be deemed responsible for air capacity or noise problems caused by failure
to comply with the above instructions and no warranty on the product shall be provided.
2. Before making the hole, check that there are no structural or other parts inside the cabinet, where
the appliance is to be placed, which could hinder a proper installation. Check that the dimensions of the
Downdraft and the ones of the cook top are compatible with the cabinet so that the installation can be
carried out properly.
5
SU-DD2-L

EN
3. Make a rectangular hole 837x100 mm for the 880mm version or 1137x100 mm for the 1180mm ver-
sion in the rear part of the hob, it is necessary to obtain the radius 10 on each corner of the rectangular
opening (see g. 2).
4. Take the accessories supplied in the package (A-B-C-D see g.3),
Fig. 3
6SU-DD2-L
Fig. 2

EN
assemble part A with B and C with D (g. 4).
7
SU-DD2-L
Fig. 4
5. Install the preassembled accessories in correspondence with the hole drilled (g. 5), bearing in mind
that they can cover different types of furniture from a minimum dimension of 860mm to a maximum
dimension of 1000mm.
Fig. 5

EN
Fix the width of the pairs of accessories using the screws supplied in the special slots, n. 2 screws on
each side (g. 6) taking care not to screw them completely.
Fig. 6
Position the accessories against the base of the hob
(A + B side 1 / C + D side 2 of the rectangular hole see g. 7)
Fig. 7
8SU-DD2-L

EN
and x them on both sides with screws (g. 8).
9
SU-DD2-L
Fig. 8
Warning: the accessories must be xed in correspondence with the rectangular hole (each pair on each
long side) at a maximum distance of 107mm (g. 9)
Fig. 9

EN
(for an good assembly take the components “E - F” g.10 and insert them between the accessories,
respectively E for the left part and F for the right part, see g.11, in order to check the correct positioning
at the height above said).
Fig. 10
Fig. 11
10 SU-DD2-L

EN
Further expedient x the accessories so that the screws previously inserted to lock the width do not go
beyond the rectangular hole (see g. 12), this to prevent the downdraft from hitting the screws during
installation.
11
SU-DD2-L
Fig. 12
Fig. 13
Before proceeding to the next point, remember to tighten the screws left slow and check that everything
is stable.
6. Take the E - F components (if not present, insert the adjustment screws as shown in g.10) position
them as previously seen (E for the left part and F for the right part, see g.11) and x them on both the
sides with screws (g. 13).
Note well the xing system has several slots to allow adjustments of the downdraft both on the basis
of its width (left - right) and on the thickness of the top to be glued on the downdraft (top - bottom) (see
g. 13).

EN
7. Install the downdraft in the hole made, inserting it from above (g. 14),
Fig. 14
Fig. 15
Place the downdraft brackets on the adjustment screws previously preassembled in the E - F compo-
nents (g. 15).
12 SU-DD2-L

EN
To determine the correct line-up of the downdraft, place the part (glued in the previous step) inside the
rectangular niche, making the magnets (G) coincide with the seat (H) and check that the two surfaces
are perfectly at the same level (g. 16.2).
13
SU-DD2-L
Fig. 16.2
Glue the part left over from the previous cut made on the worktop to the support supplied (g. 16.1).
The part to be glued must weigh a maximum of 5kg and must respect the following dimensions:
Fig. 16.1
833 mm x 97 mm_R8 mm (880 version)
1133 mm x 97 mm_R8 mm (1180 version)

EN
8. After completing the installation, fasten the push-button panel below the top immediately behind the
cabinet doors (see g.18A for central installation, g.18B for lateral installation). Before xing the push-
button panel, check that the doors are actually closed.
Fig. 18
Fig. 19
Connect the button cable to the electrical system and immediately after the product to the power grid, lift
the downdraft, remove the door lock and then open the door (g. 19).
14 SU-DD2-L
Fig. 17
If the downdraft is not aligned, act on the screws previously seen in g. 15 until correct alignment is
achieved.
Fasten the downdraft to the cabinet using the two brackets supplied (g. 17).
Having veried the correct position and stability of the product, proceed to glue the additional surface
on the top of the downdraft.

EN
In the version of the Downdraft equipped with internal motor, install the power unit orienting the air outlet
to the desired position, either downwards or upwards (Fig. 21). The motor can be installed either on the
front or rear side of the downdraft.
15
SU-DD2-L
Fig. 21
After having installed the motor, connect the air ducts.
Position the lters (g. 20).
Fig. 20

EN
9. For versions with external motor, place the suctioning unit (external motor) in a suitable area and t
the exhaust air ue as illustrated. Then t the air outlet ducts between the external motor and the down-
draft. Select an air outlet from the ve possibilities (Fig. 22) and t the union supplied with the appliance.
Fig. 22
10. Place the metal box with the electronic components in an easily reachable area for eventual techni-
cal assistance operations. (Fig.23),
Fig. 23
16 SU-DD2-L

EN
connecting the three connectors (9 pole connector for the actuator control and the safety control, 4 pole
connector for led lamp turn on and push-button connector) (Fig. 24).
17
SU-DD2-L
Fig. 24
11. Connect the internal motor or te eternal motor’s cable to the terminal board found in- side te plastic
box of the downdraft wiring.
Make sure to respect the colors of cables when performing the electrical connection (Fig. 25).
Fig. 25
12. Power the cookerhood.

EN
Fig. 26
This appliance is intended to suck cooking fumes, greases and steam. It has been designed to work in
both suctioning mode, with outside evacuation, and ltering mode.
Outside - discharge version
The cooker hood can be mounted in the version with outside discharge of suctioned air: in this case it
is necessary to connect the exhausting channel to the outside (exhausting pipes are not supplied with
the products.)
Non-return valve blockage
WARNING
Before connecting the air exhaust hose, make sure that the non-return valves can rotate freely. (Fig.26)
18 SU-DD2-L
HOW TO USE THE COOKER HOOD

EN
In case of outside air discharge installation, t a non-return valve to prevent wind and back air from
entering.
19
SU-DD2-L
Fig. 27
Filtering mode
In case fumes and vapour cannot be evacuated outside, the appliance can be used in the ltering mode.
Activated charcoal lters are required for this type of cooker hood. Air recycled through the charcoal l-
ters is recirculated into the kitchen, thanks to a duct conveying the air on one side of the cabinet (Fig.27)
CAUTION
Installation must comply with the regulations in force regarding the ventilation of enclosed environments.
In particular, discharged air must not be conveyed into a duct used for fumes discharge or discharge
from appliances using gas or other combustible materials. The use of discontinued ducts is not allowed
without the approval of a qualied technician.

EN
GREASE FILTER REMOVAL, MOUNTING THE ACTIVATED CHARCOAL FILTER
The removal and tting of the grease and carbon lters need to be carried out with the downdraft in the
open position. To open the downdraft, push the key. Then remove the front panel, pushing the upper part
of each side at the same time. The panel will rotate forwards to make it possible to access the grease
lters (Fig. 20). Remove the grease lters to access the carbon lters (Fig. 28). The replacement of the
charcoal lters has to be carried out accordingly to the effective use of the Downdraft, and in any case
at least once every 6 months.
Fig. 28
WARNING
After having replaced the lters, reinstall the front stainless steel pan’el, otherwise the Downdraft is not
enabled to function.
20 SU-DD2-L