Bernini Murano User manual

Murano
Color Changing glass Ball Fountain
Owner’s Manual

PLEASE READ FIRST BEFORE RETURNING
Please call us for assistance at 0203 617 1773
or email us at: [e-mail]
If you have any questions regarding assembly, parts, or operation,
please visit our website at www.Berninifountainsuk.com. You will nd
instructional videos on how to assemble and operate your fountain, and
keeps you up to date on our newest products. You can also email us
with any questions you have.
This product comes with a six (6) month limited warranty
against materials and workmanship.
Please review the list of accessories included with your
Bernini™ Fountain on the next page. Please note, images of parts
are not to scale with one another.

CONTENTS
Step1: Base & Bowl
Bowl Locking System
Step2: Base & Light/Pump Tier
Installing e LED Light Ring
Connecting e Water Pump
Installing e Light/Pump Tier
Fill Your Fountain
Step 3: Fountain Glass Globe Installation
Step 4: Battery Installation
Connecting e Battery
Inserting e Battery Compartment Door
Removing e Battery Compartment Door
Step 5: Setting Up Your Fountain
Operating Your Fountain
Troubleshooting and Maintenance
Cleaning Your Fountain
Cold Storage
Recharging e Battery
Cleaning e Water Pumps’ Parts
Water Pump's Air Filters
Water Pump's Impeller
Priming e Water Pump
Using Leveling Shims
Weighing Down Your Fountain
Water Pump's Connection
1
2
4
5
6
6
8
9
12
13
14
14
15
16
19
19
19
19
20
20
20
21
22
22
23

Parts for Your Bernini™ Fountain
Battery
Compartment
Door
Light/Pump
Tier
Glass Globe
Rechargeable
Battery Leveling Shim
Connection
Port
Parts for your
Bernini™Fountain:
Battery Charger
LED Light Ring Water Pump
Assembly
Base
Bowl

Remember if you need help contact Customer Care: 0203 617 1773
1|
You will need:
Step 1:
Base & Bowl
Base
Bowl

|2
Remember if you need help contact Customer Care: 0203 617 1773
Bowl Locking System
A look at how the bowl locking works on your Fountain.
Bottom of the bowl Top of base
Note: You will notice that there are two dierent sized tabs on the bottom of the bowl and
there are two corresponding grooves in the top of the base. These tabs t together and
lock when turned clockwise.
Step 1: Be sure to place the
base of your fountain on a at,
rm surface.
Step 2: Apply downward
pressure by stepping on the
edge of the base to prevent
it from turning.
Align and connect the bowl
to the base.
Step 3: Turn the bowl a
quarter turn clockwise to
lock it into place.

3|
Remember if you need help contact Customer Care: 0203 617 1773
At this point, your fountain should look like the image
on the left. Go to the next page for the next step to
setup your new Bernini™ Fountain.
Bowl Locking System (Continued)

|4
Remember if you need help contact Customer Care: 0203 617 1773
You will need:
Step 2:
Base & Light/
Pump Tier
Assembly
Bowl and Base
Assembly
Light/Pump
Tier
LED Light Ring
Water Pump
Assembly

5|
Remember if you need help contact Customer Care: 0203 617 1773
In this step you will install the LED Light Ring
into the Light/Pump Tier.
NOTE: Please ensure to align the cord with one
of the 3 groves in the Housing. Not doing so will
cause the Ring to improperly seat into the Housing
and cause it to come loose easily.
Step 1: Find the LED Light Ring cord with the
green plug and feed into the top of the Light/
Pump Tier.
Step 2: Set the LED Light Ring into the Housing,
again ensuring that the LED Light Ring Cord is
aligned with one of the 3 groves in the Housing.
Step 3: Firmly press the LED Light Ring into the
housing until you feel a snap, this means that the
LED Light Ring has seated into the Housing.
Note: This will not require an excessive
amount of force.
Installing e LED Light Ring
Set the Light/Pump Tier on a level sturdy surface for assembly.

|6
Remember if you need help contact Customer Care: 0203 617 1773
Step 1: Grasp the Water Pump in one hand and, with the other hand grasp the hose that
goes to the top of the Light/Pump Tier. Push the hose onto the discharge nipple on the
discharge side of the water pump. If this step proves dicult apply a twisting motion while
pushing together.
Connecting e Water Pump
Installing e Light/Pump Tier
Set the Light/Pump Tier on to the edge of the upper base. There are 3 square tabs (white arrows) that the
Tier will sit on and 3 round tabs (black arrows) that will lock the Tier in place. You will use this to install the
Light/Pump Tier at the end of this section.

Remember if you need help contact Customer Care: 0203 617 1773
7|
Installing e Light/Pump Tier (Continued)
Step 1: The Light/Pump Tier has 2 cords, one
attached to the pump and one attached to the
Colored LED Lights. Feed the black cord and
the green cord down into the pipe. These will be
connected to the Connection Port in a later step.
NOTE: If the cables slip out of the rubber stopper,
you can press the cables into the slot in the side
of the rubber stopper. Maneuver the cord to t
snugly inside the hole that is located in the center
of the rubber stopper.
Step 2: Firmly press the plug into the pipe in the
middle of the bowl.
If you are having trouble pressing the plug into the
pipe, you can rub a small amount of soapy water on
the plug to help it slide into place.
Step 3: To ensure that you have a good seal,
make sure the plug ts snugly as pictured above.

Remember if you need help contact Customer Care: 0203 617 1773
|8
At this point, your fountain should look like the image on the
left. Go to the next page for the next step to setup your new
Bernini™ Fountain.
Line up the 3 rounded notches in the Light/Pump Tier with the 3 corresponding notches in the base of
the fountain. Set the Tier down onto the square tabs and rotate a quarter of a turn either clockwise or
counter clockwise. Please refer to the image above.
The assembly of the Light/Pump Tier is now complete
and should look like the image to the left. In the following
section you will be installing the Fountain Globe.
Fill Your Fountain
Fill the small bowl built into the upper portion of the base until
the water is about 1 inch (2.5 centimeters) from the top of the
bowl, just below the tabs that support the Light/Pump Tier.
After you have lled your fountain, hold both sides of the large
bowl and quickly shake your fountain for ten seconds. This is
to dislodge any air bubbles that may be caught in your water
pump. Press the C button once to turn on your fountain. Water
should be owing from the top of your fountain. If water is not
owing, press the C button once more to turn your fountain o,
and repeat the step above. Once the air bubbles are removed,
turn the pump o and you are ready to move to the next section.
Installing e Light/Pump Tier (Continued)

Remember if you need help contact Customer Care: 0203 617 1773
9|
Glass Globe
Assembled Base
You will need:
Step 3:
Fountain Glass
Globe Installation

Remember if you need help contact Customer Care: 0203 617 1773
|10
Note: You will notice that there are two dierent sized tabs on the bottom of the Glass Globe and there
are two corresponding grooves in the top of the Light/Pump Tier. These tabs t together and lock when
turned clockwise.
Bottom of Glass Globe Top of Light/Pump Tier
Step1: Be sure to place the
base of your fountain on a
at, rm surface.
Step 3: Once tabs are aligned
turn the Glass Globe a quarter
turn clockwise to lock it into
place.
Step 2: Using your foot, apply
downward pressure by stepping on
the edge of the base to prevent it
from turning.
Align tabs in Light/Pump Tier with
the tabs in the Glass Globe.
Fountain Glass Globe Installation

Remember if you need help contact Customer Care: 0203 617 1773
11|
At this point, your fountain should look like the image on
the left. Go to the next page for the next step to setup your
new Bernini™ Fountain.
Fountain Glass Globe Installation (Continued)

Remember if you need help contact Customer Care: 0203 617 1773
|12
Fountain
Assembled
Rechargeable
Battery
Battery
Compartment
Door
You will need:
Step 4:
Battery
Installation
Connection Port

Remember if you need help contact Customer Care: 0203 617 1773
13|
Connecting The Battery
Step 2: Using the cords from
inside the base and the cord
from the battery, connect the
color coded cords to their
corresponding receptacles on
the connection port.
Use the image below for more
help on connecting the battery.
Step 3: Place your connection
port inside the designated angled
area located at the back of your
fountain base.
(See illustration below)
Step 4: Place the battery inside
of the compartment in front
of the connection port. (See
illustration)
DO NOT PLACE BATTERY
UPSIDE DOWN INSIDE OF
BATTERY COMPARTMENT.
Step 1: In the open battery
compartment, you will see three
cords hanging down that you
must connect to the connection
port.
If you do not see the three cords
inside the battery compartment,
reach up into the base and gently
pull them down until they are hanging
inside the battery compartment.
Gray
Black
Blue
Green
Gray
(Battery)
Blue
(ABCD Button)
Green
(LED Lights)
Black
(Water Pump)
AA
BB
CC
DD
NOTE: USE CAUTION WHEN PLACING BATTERY INSIDE THE COMPARTMENT. DUE TO THE
MANUFACTURING PROCESS THERE MIGHT BE SHARP EDGES.

Remember if you need help contact Customer Care: 0203 617 1773
|14
Step 1: Start by lining up the
notch on the bottom of the
battery compartment door
with the notch in the bottom
of the battery opening.
Step 1: Carefully remove
the battery compartment
door from the base by gently
pulling outward from the top.
Step 2: Push the battery
compartment door in toward
the base. You will know it is
in position when the magnet
locks the door in place.
Step 2: Then, pull the battery
compartment door up and out
to remove from the base.
Once the door is in place,
you may notice a small notch
in the bottom left corner of
the battery compartment
door. This is for the optional
Bernini™ solar panel cord.
DO NOT OVEREXTEND THE
BATTERY COMPARTMENT
DOOR BY PULLING DOWN!
This may cause damage to your
new Bernini™ Fountain.
Inserting The Battery Compartment Door
After you have connected the cables inside your fountain to the rechargeable battery, you should
then place the battery compartment door on the base of the fountain.
At this point, your fountain should look like the image on
the left. Go to the next page for the next step to setup
your new Bernini™ Fountain.
Removing The Battery Compartment Door

Remember if you need help contact Customer Care: 0203 617 1773
15|
Fountain
Assembled
You will need:
Step 5:
Setting Up Your
Fountain